Best MIG Welder Under $500: 6 Picks for Home and Farm Use
Six dual voltage MIG welders under $500, scored on rated output, duty cycle, warranty and what each listing leaves out.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallARCCAPTAIN MIG200P9.5/10View on Amazon - 2
Budget PickFEMEROL MIG 250PRO9.5/10View on Amazon - 3
Most PortableARCCAPTAIN MIG1609.5/10View on Amazon - 4
Most Complete KitTOOLIOM MIG-180 PRO9.5/10View on Amazon
This guide is for home, farm and hobby welders who want a MIG machine under $500 that can also run flux core, and who care more about duty cycle, input voltage and what is in the box than about the biggest number on the front. Each listing advertises 110V and 220V input, and we compared them on what each listing actually states.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall ARCCAPTAIN MIG200P: Pulse MIG, spool gun support and a stated 2 year warranty, the highest Gear Score here. Check price on Amazon
- Budget Pick FEMEROL MIG 250PRO: The lowest priced machine here when we collected listings, with aluminum wire support and a stated 2 year guarantee. Check price on Amazon
- Most Portable ARCCAPTAIN MIG160: A stated 11.8 lb, the lightest machine in this guide by a wide margin. Check price on Amazon
- Most Complete Kit TOOLIOM MIG-180 PRO: The only stated duty cycle here, 60% at 180A, and a Lift TIG torch in the box. Check price on Amazon
The machines

ARCCAPTAIN Pulse MIG Welder 200A Aluminum Welding
A 200A pulse MIG machine with spool gun support and a stated 2 year warranty, at the top of the budget.
Pros
- Pulse MIG mode for lower heat input on thin steel and aluminum, per the listing
- Takes both 2 lb and 10 lb wire spools
- Supports a spool gun, Lift TIG and stick from one machine
- Listing states a 2 year manufacturer warranty
Cons
- No duty cycle rating in the listing
- The title says 110V and 220V but the listing table shows 220 volts only
- Spool gun and Lift TIG torch are sold separately
- Few owner ratings so far, first listed in May 2026

FEMEROL 250A MIG Welder,6 in 1 Gas MIG/Gasless
The lowest priced machine here when we collected listings, with a 250A rating, aluminum wire support and a stated 2 year guarantee.
Pros
- Lists .023 to .035 inch steel wire and .035 to .045 inch aluminum wire
- Two ways to run aluminum: a Teflon liner or a spool gun
- States a 2 year guarantee in the listing
- Six modes including spot welding and Lift TIG
Cons
- No duty cycle rating in the listing
- The 14 mm plate claim does not say single pass or multi pass
- TIG torch and spool gun are not included
- Input listed only as 110V/220V, with no output figure for either

ARCCAPTAIN 160A MIG Welder 110V 220V Gasless Gas
The lightest machine in this guide at a stated 11.8 lb, with dual voltage and a 2 year manufacturer warranty.
Pros
- Listed at 11.8 lb in the description, easy to carry with the strap
- Synergic setup matches settings to the wire size you pick
- Takes .030, .035 and .040 inch wire
- Listing states a 2 year manufacturer warranty
Cons
- No duty cycle rating in the listing
- The listing does not say what accessories are in the box
- Lift TIG torch is sold separately
- No maximum thickness stated

TOOLIOM 180A 110/220V 4-in-1 MIG Welder Kit
The only machine in this guide that states a duty cycle with an amperage, and it ships with a Lift TIG torch.
Pros
- States a 60% duty cycle at 180A
- Lift TIG torch, gloves and 1 lb of flux core wire in the box
- Manual inductance control from -10 to +10
- Stick mode with adjustable hot start, arc force and VRD
Cons
- No warranty term in the listing
- The duty cycle does not say which input voltage it applies to
- Very few owner ratings so far
- Item weight of 30.5 lb, close to the full size machines here

YESWELDER 205A MIG Welder
The most rated machine in this guide, a 205A five mode welder with a wide wire speed range and fine voltage trim.
Pros
- Five modes including spool gun aluminum MIG
- Wire speed adjustable from 58 to 858 inches per minute
- Synergic voltage with plus or minus 3V fine tuning
- Gas hose, MIG torch and a 220V to 110V adapter in the box
Cons
- No warranty term in the listing
- No duty cycle rating in the listing
- Spool gun and Lift TIG torch are sold separately
- Heaviest machine here at 37.5 lb item weight

YESWELDER 160A MIG Welder
A 160A four mode machine that takes 10 lb spools and lists common stick rods, a simple first welder for steel.
Pros
- Takes both 2 lb and 10 lb spools of .030 and .035 inch wire
- Listing names 6010, 6011, 6013 and 7018 rods for stick mode
- Synergic control sets voltage and wire speed from thickness or amperage
- 220V to 110V adapter and gas hose in the box
Cons
- No warranty term in the listing
- No duty cycle rating in the listing
- Weight is stated as 19.4 lb in the description and 27.5 lb in the table
- Lift TIG torch is sold separately
Other welders and gear to compare
YESWELDER 165A MIG WelderCheck price on Amazon
FEMEROL Plasma Cutter Welder Combo 200A Gas MIG/GaslessCheck price on Amazon
VEVOR Pro MIG WelderCheck price on Amazon
YESWELDER 135A MIG WelderCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Max output | Input | Duty cycle | Processes | Weight | Warranty |
|---|---|---|---|---|---|---|---|
| ARCCAPTAIN MIG200P | 9.5/10 | 200A | 110V/220V (table: 220V) | Not stated | Pulse MIG, MIG, flux core, TIG, stick, spot | 32.8 lb | 2 years |
| FEMEROL MIG 250PRO | 9.5/10 | 250A | 110V/220V | Not stated | MIG, flux core, stick, TIG, spot | 32.6 lb | 2 years |
| ARCCAPTAIN MIG160 | 9.5/10 | 160A | 110V/220V | Not stated | MIG, flux core, TIG, stick | 11.8 lb | 2 years |
| TOOLIOM MIG-180 PRO | 9.5/10 | 180A | 110V/220V | 60% at 180A | MIG, flux core, stick, TIG | 30.5 lb | Not stated |
| YESWELDER MIG-205DS PRO | 9.5/10 | 205A | 110V/220V | Not stated | MIG, flux core, spool gun, TIG, stick | 37.5 lb | Not stated |
| YESWELDER YWM-160 | 9.4/10 | 160A | 110V/220V | Not stated | MIG, flux core, stick, TIG | 19.4 lb | Not stated |
Ratings in this table are the makers’ own claims taken from each product page (4 October 2026). Where a listing states a weight two ways, the table shows the figure from the product description.
What matters in a MIG welder under $500
Input voltage and your outlet
All six listings advertise 110V and 220V input, though the ARCCAPTAIN MIG200P shows only 220 volts in its specification table. None of the six states its maximum output on 110V, so do not assume the headline amperage applies on a household outlet. If you plan to weld thicker steel, budget for a 240V circuit installed by a licensed electrician.
Duty cycle, and why most listings skip it
Duty cycle tells you how long a machine can weld before it needs to cool, as a share of a 10 minute period at a stated amperage. Of the 13 welder listings we looked at in this price range, only one gave a duty cycle with an amperage: the TOOLIOM MIG-180 PRO at 60% at 180A, or about 6 minutes in every 10. Another gave 60% with no amperage, which cannot be compared. If you weld long seams, ask the seller for the figure before you buy.
Flux core or gas
Every machine here runs gasless flux core wire, which works outdoors in a breeze and needs no cylinder. Solid wire with shielding gas gives cleaner welds on thin sheet but needs a cylinder and a regulator. The listings that mention a gas hose do not list a regulator, so plan to buy one.
What is in the box
Lift TIG and spool gun modes usually need a torch or gun sold separately. Only the TOOLIOM ships with a Lift TIG torch. If you want aluminum, the ARCCAPTAIN MIG200P, FEMEROL MIG 250PRO and YESWELDER MIG-205DS PRO list spool gun support.
Warranty and safety listings
Across the 13 listings, 6 stated a warranty term and none stated a CSA, UL or ETL listing. That is why no machine here scores above zero for safety, and why the three with a stated 2 year term pull ahead on warranty.
Before you strike an arc. Wear a helmet with the right shade for the process and amperage, flame resistant clothing and leather gloves, weld with good ventilation, and clear anything flammable from the area. See the OSHA welding overview and our Safety Disclaimer.
FAQ for welders
Can a MIG welder under $500 run on a household outlet?
All six listings advertise 110V input, though one, the ARCCAPTAIN MIG200P, shows only 220 volts in its specification table. None of the listings states the maximum output on 110V, so check the manual for the circuit and breaker it needs before you plug in.
Do I need shielding gas?
No. Every machine here runs gasless flux core wire. For solid wire MIG you need a gas cylinder and a regulator, which these listings do not include.
What does a 60% duty cycle at 180A mean?
It means the machine can weld for about 6 minutes in every 10 at 180A before it needs to cool. At lower amperage the usable time is longer. A duty cycle without an amperage cannot be compared between machines.
Can these machines weld aluminum?
Three of them list aluminum support through a spool gun sold separately: the ARCCAPTAIN MIG200P, FEMEROL MIG 250PRO and YESWELDER MIG-205DS PRO. The FEMEROL listing also describes running aluminum wire with a Teflon liner.
How thick a plate can a MIG welder under $500 handle?
Few of these listings say. The FEMEROL claims mild steel plate up to 14.0 mm without stating the number of passes, and the ARCCAPTAIN MIG200P gives only its thinnest weldable thickness, 0.039 inch. Treat thickness claims without a pass count as manufacturer rated.
Related: best MIG welder under $1000, best 120V MIG welder, best flux core welder, best welder for beginners, and the MIG welders hub. Also see our MIG spatter causes and fixes. Also see our best mig welder under 300. Also see our best flux core welder under 200. Also see our best welder generator. Also see our what is synergic mig welding.
More related guides (217)
- best extension cord for portable welder
- welding machine types
- best welding machine for stainless steel
- best welder under 400
- best welder for body panels
- flux core welding vs tig
- flux core welding vs stick welding
- inverter welder vs transformer welder
- why does my mig wire keep burning back to the tip
- how to fix mig wire birdnesting
- can you run a mig welder on a 15 amp circuit
- can you mig weld without gas
- hobart handler 140 vs 140ez
- what causes porosity in mig welds
- flux core vs mig with gas
- millermatic 141 vs 142
- 120v vs 240v mig welder
- mig welder settings for 1/8 inch steel
- mig welder wire speed and voltage chart
- how to set gas flow rate for mig welding
- how thick can a 120v mig welder weld
- mig welder duty cycle explained
- what size mig wire for sheet metal
- how to mig weld thin sheet metal without burning through
- what size generator to run a mig welder
- what polarity for flux core welding
- how to change the wire spool on a mig welder
- push vs pull mig welding
- mig welding stick out length explained
- how long does a 10 lb spool of mig wire last
- harbor freight titanium vs hobart mig welder
- mig welding vertical up vs vertical down
- yeswelder vs hobart mig welder
- best mig welder with spool gun included
- spool gun settings for aluminum
- gasless mig welding for beginners
- stud welder for aluminum
- best handheld laser welder cost
- is gasless mig welding strong
- flux core welding pros and cons
- stud welder sizes
- gasless mig welder pros and cons
- what is a stud welder
- mig welder problems
- best welding machine company
- welder maintenance
- stick vs mig welder
- stick vs tig welder
- dual voltage vs single voltage welder
- spool gun vs push pull gun
- welding equipment for beginners
- tooliom 200a review
- tooliom 135a review
- multi-process welder vs tig welder
- pulse mig vs standard mig welder
- engine driven welder vs portable generator
- rotary positioner vs welding turntable
- pyrex cup vs ceramic tig cup
- analog vs digital tig welder
- rotary phase converter vs vfd for welder
- laser welder vs cold welder
- single phase vs 3 phase welder
- dual pulse mig vs single pulse mig
- gas mig vs gasless flux core welder
- laser welder for battery terminals
- welder backpack for men
- stick welder vs multi-process welder
- best all around stick welding rod
- oxy acetylene vs stick welder
- mig vs tig for auto body
- angle clamp vs c clamp
- portable vs stationary welder
- oxy acetylene vs mig welder
- best welder backpack under 80
- 1/16 vs 3/32 tungsten electrode
- forney vs hobart mig welder
- tig vs stick welding for pipe
- mig vs tig for stainless steel
- portable mig vs portable stick welder
- spot welder vs mig welder
- synergic mig vs pulsed mig welder
- ac tig vs dc tig welder
- pure tungsten vs thoriated tungsten
- 308 welding rod vs 309
- welding jacket vs welding sleeves
- oxy acetylene vs tig welder
- air cooled vs water cooled mig gun
- best welding cable under 50
- 1/0 vs 2/0 welding cable
- analog vs digital mig welder
- best welding goggles for grinding
- best welding cable for home shop
- copper vs aluminum welding cable
- stick welder vs mig welder for truck repairs
- best cutting fluid for metal
- 20v vs 60v cordless angle grinder
- welding cable vs jumper cable
- best extension cord for mig welder
- best welder backpack for job site
- flux core vs mig for thick steel
- flux core vs stick for farm repairs
- mig vs stick for thick steel
- left vs right cut aviation snips
- best cable lugs under 15
- flux core vs stick for outdoor use
- mig vs stick for auto body
- 120v mig vs 120v tig welder
- tig vs stick for stainless steel
- flex head vs rigid tig torch
- best spot welder for hobbyists
- wool vs fiberglass welding blanket
- best welding electrode holder for farm use
- welding plug adapter
- flux core vs mig for outdoor use
- mig vs tig for mild steel
- stainless steel chipping hammer
- mig vs tig for thick steel
- tig vs stick for farm repairs
- tig vs stick for home garage
- tig vs stick for mild steel
- welding cable kits 25 50 feet
- welding machine extension cord 50 amp
- welder extension cord 8 awg
- mig vs stick for mild steel
- tig vs mig for cast iron
- flux core vs stick for truck repairs
- dinse vs tweco welding connector
- hobart handler 140 vs 190
- inverter generator vs conventional generator for welding
- hobart handler 140 vs yeswelder mig-205ds
- flux core vs mig for galvanized steel
- mig vs stick for rusty metal
- inverter generator for welder
- best inverter generator for welder under 1000
- 25 vs 50 ft extension cord for welder
- tig torch vs mig gun
- 2 awg welding cable
- lincoln power mig 180c vs yeswelder mig-205ds
- aluminum welder rods
- welding hose reel retractable
- best mig welder that runs on a generator
- best dual pulsed mig welder
- best spot welder for auto body
- best pulse mig welder for aluminum
- mig welding for beginners
- mig welding machine for beginners
- mig welder set up
- welder kit for beginners
- parts of tig torch
- how do you tig weld aluminum
- epdm vs pvc welding cable
- stud welder dent repair kit
- flux core wire welding tips
- can aluminum be mig welded
- air chipping hammer kit set 190 mm
- best welding machine for auto body work
- best welding plug adapter under 30
- gasless vs gas mig welder
- wire feeder vs spool gun
- stick welding for beginners
- tig torch set up
- mig welder for auto body repair
- spot welder tips
- 240v flux core vs 240v stick welder
- flux core welding settings chart
- mig welder wire feed problems
- mig welder types
- tig welding aluminum problems
- welding cable connector types
- how hot is a welding torch
- mig welding amperage chart
- tig welding tips and tricks
- types of tig welders
- tig welding torch types
- mig welding overhead tips
- uses for spot welder
- mig vs stick for aluminum
- stick welding tips and tricks
- aluminum mig welding tips
- manual metal arc welder
- welding torch types
- vertical stick welding tips
- flux core welding setup
- spot welder parts
- carbon arc gouging setup
- how to set up a welding machine
- best inverter generator with electric start
- spot welder for car body repair
- water cooled tig torch setup
- mig wire feeder parts
- how to set oxy acetylene regulators for cutting
- brazing torch setup
- welding cable price
- diagram arc welding machine parts
- portable laser welding machine price
- stick welding machine for beginners
- aluminum mig settings chart
- flux core welding problems
- are flux core welders any good
- stick welder price
- how to flux core weld sheet metal
- best heavy duty hand truck
- grinding disc for concrete
- hvlp spray gun vs conventional spray gun
- tapping drill chart
- size s drill bit
- welder repair
- parts of a mig welder
- 6 combination square
- hand truck small
- best flux core welder for auto body repair
- best fume extractor for laser cutting
- micrometer set 0-12
- non digital caliper
- media blast vs sandblast
- best welder for auto body
- dial bore gauge vs telescoping gauge
Background reading: how to choose a MIG welder, welding duty cycle explained flux core vs MIG and how to spot a good welder deal on Black Friday.
Scoring, line by line
Each machine is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. A spec the listing does not publish scores nothing.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| ARCCAPTAIN MIG200P | 9.5 | 32 | 20 | 19 | 0 | 3 |
| FEMEROL MIG 250PRO | 9.5 | 27 | 19 | 22 | 0 | 3 |
| ARCCAPTAIN MIG160 | 9.5 | 27 | 19 | 22 | 0 | 3 |
| TOOLIOM MIG-180 PRO | 9.5 | 29 | 20 | 24 | 0 | 0 |
| YESWELDER MIG-205DS PRO | 9.5 | 30 | 21 | 19 | 0 | 0 |
| YESWELDER YWM-160 | 9.4 | 27 | 20 | 22 | 0 | 0 |
The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure.






