Stick Welder vs Multi-process Welder: Which One Should You Buy?
Stick welder vs multi-process welder: one process or many? Concrete figures on amperage, processes, weight and voltage from the listings.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
YESWELDER 140A MIG Welder9.6/10View on Amazon - 2
HONE Stick Welder 110vView on Amazon - 3
ARCCAPTAIN 250A Stick WelderView on Amazon - 4
ESAB® HandyArc 1/8" Stick WelderView on Amazon - 5
Stick WelderView on Amazon - 6
Forney 271 Easy Weld 140 MP Multi-Process WelderView on Amazon - 7
FEMEROL Plasma Cutter Welder Combo 200A Gas MIG/GaslessView on Amazon
In the stick welder vs multi-process welder question, the difference is simple: a stick welder is built around one process, shielded metal arc welding with a consumable electrode, though several of the listings we reviewed add lift TIG as a second mode. A multi-process welder does several: typically MIG, flux core, stick and TIG in one box, and sometimes a plasma cutter too. If your work is repairs on steel with a rod, a stick welder is enough. If you want to weld sheet, aluminum or stainless with wire and TIG, one multi-process machine covers it. The rest of this guide explains the differences with concrete figures from the listings we reviewed.
Other welders and gear to compare
HONE Stick Welder 110vCheck price on Amazon
ARCCAPTAIN 250A Stick WelderCheck price on Amazon
ESAB® HandyArc 1/8" Stick WelderCheck price on Amazon
Stick WelderCheck price on Amazon
Forney 271 Easy Weld 140 MP Multi-Process WelderCheck price on Amazon
FEMEROL Plasma Cutter Welder Combo 200A Gas MIG/GaslessCheck price on Amazon
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
The difference in one paragraph
A stick welder is built around a single process: stick electrodes, with several of the listings we reviewed adding lift TIG as a bonus mode. The stick machines we reviewed run 135A to 250A on 110V or 110V/220V dual voltage, weigh 3.3 to 8.58 lbs by their bullet figures, and span rod sizes from 1/16 in to 5/32 in across the listings. A multi-process welder packs several processes into one box: the Weldpro Omni210 listing, for example, offers MIG, stick, AC/DC TIG, spool gun and flux core at up to 200A on 110V/220V, while the YESWELDER MCT-520 listing adds a plasma cutter with 20-50A cutting. The trade is weight and complexity: the multi-process listings weigh 46.5 to 81.8 lbs against the stick side’s 3.3 to 8.58 lbs.
Stick welder vs multi-process welder: side by side
| Factor | Stick welder | Multi-process welder | Edge |
|---|---|---|---|
| Example amperage | 135A to 250A (listed) | 200A (listed) | Stick |
| Processes | Stick only; some add lift TIG (listed) | MIG, flux core, TIG, stick, spool gun, plasma (listed) | Multi-process |
| Voltage | 110V; some 110V/220V (listed) | 110V/220V (listed) | Multi-process |
| Weight | 3.3 to 8.58 lbs (listed) | 46.5 to 81.8 lbs (listed) | Stick |
| Rod or wire | Rods 1/16 in to 5/32 in (listed) | MMA to 200A; 12 lb spool (listed) | Even |
| Cutting | Not stated | 5/16 in clean cut (listed) | Multi-process |
Figures are from the listings reviewed, collected 19 October 2026; a figure from one listing describes that listing only.
When a stick welder is the better choice
Stick is the repair process. The HONE listing covers low-carbon steel, cast iron, mild steel and stainless from 0.05 to 0.22 inch thick on a 20-205A range, and the HGNVGZ listing handles carbon steel up to 1/8 in thick with 1/16 in to 3/32 in rods. For fence, gate, trailer and farm repairs outdoors, where wind blows shielding gas away, a light 110V-class stick machine is the practical tool. See the stick welder picks.
When a multi-process welder is the better choice
Multi-process is the one-machine shop. The Weldpro Omni210 listing gives MIG, stick, AC/DC TIG, spool gun and flux core at up to 200A on 110V/220V, with a 12 lb wire spool capacity. The YESWELDER MCT-520 listing goes further: six modes including a plasma cutter that makes a 5/16 in clean cut and a 5/8 in maximum sever. If your work mixes sheet metal, aluminum and stick repairs, one 46.5 to 81.8 lb machine replaces three. The YESWELDER listing also states a 2-Year Warranty with 24/7 North American tech support, which is the strongest support term in the listings reviewed. See is a multi-process welder worth it.
How to tell what a machine supports
Read the process list, not the headline. A machine sold as a stick welder may add lift TIG: the HONE, Rotvik and TOOLIOM listings all pair stick with lift TIG, with the Rotvik including the torch and a 2 Year Manufacturer warranty. But lift TIG is scratch or touch start; the Weldpro listing offers HF start with a foot pedal, which is the full TIG setup. If the listing says spool gun compatible, that is the aluminum ticket; if it says CUT with an amperage like 20-50A, it has a plasma cutter built in. For the record, the ESAB listing reviewed here is the MINIARC Rogue ES 180i stick system at 180A, with a UL specification and a stick 6010 mode; the TOOLIOM 135A listing is a stick welder with lift TIG, not a MIG-only machine; and the MIG capability in this guide comes from the multi-process Weldpro and YESWELDER listings, not from dedicated MIG-only machines.
What about weight and power
Stick-only machines are light because they are simple: 3.3 lbs for the Siasky, 3.5 lbs for the HGNVGZ, 4.4 lbs for the HONE, all on 110V. Multi-process machines are heavy because they carry more: 46.5 lbs for the YESWELDER, 81.8 lbs for the Weldpro, both on 110V/220V dual voltage. And mind the HGNVGZ’s own warning: 1/4 in plate needs a 220V machine, and on a 15A household circuit the breaker may trip at higher amperage. See multi-process vs dedicated MIG.
FAQ for welders
Can a stick welder do TIG?
Some can do lift TIG: the HONE, Rotvik and TOOLIOM listings pair stick with lift TIG, though the TOOLIOM notes the torch is sold separately. Full HF-start TIG with a pedal is a multi-process feature here.
Is a multi-process welder as good at stick as a dedicated stick welder?
The multi-process listings offer MMA/stick modes up to 200A: the Weldpro listing pairs hot start with arc force, and the YESWELDER listing offers MMA arc force, matching the dedicated machines’ 135A to 250A range. The difference is not the arc; it is the weight and bulk of the extra processes.
Do I need 220V?
For 1/4 in plate the HGNVGZ listing says a 220V machine is the better fit. The Eioehtl, Weldpro, YESWELDER, Rotvik and TOOLIOM listings all support 110V/220V dual voltage.
Can one machine cut metal too?
The YESWELDER MCT-520 listing includes a plasma cutter at 20-50A, with a 5/16 in clean cut and 5/8 in maximum sever. No stick-only listing here cuts.
Which is better for a beginner?
A 110V stick machine is simpler and lighter: the HGNVGZ and Siasky listings pitch beginners explicitly. A multi-process machine is better if the beginner wants to learn MIG and TIG too, and the YESWELDER listing claims a 5-minute setup.
Related: flux core vs multi-process welder, multi-process vs TIG welder and TIG torch for stick welder.




