Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

HVLP Spray Gun vs Conventional Spray Gun: Which One Should You Buy?

Two HVLP spray guns and one conventional pressure feed gun, compared on feed, tips, cups, air needs and weight, from what each listing states.

HVLP Spray Gun vs Conventional Spray Gun: Which One Should You Buy?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1HVLP Air Spray Gun with 1.4/1.7/2mm Nozzles & AirHVLP Air Spray Gun with 1.4/1.7/2mm Nozzles & Air9.6/10View on Amazon
  2. 2BANG4BUCK High Performance HVLP Gravity Feed SprayBANG4BUCK High Performance HVLP Gravity Feed Spray9.6/10View on Amazon
  3. 3Binks 2100 Paint Spray Gun 2101-2800-7 63BSS 63PBBinks 2100 Paint Spray Gun 2101-2800-7 63BSS 63PB9.6/10View on Amazon

Verdict. For primer, base coat and clear coat work, pick the HVLP side of this hvlp spray gun vs conventional spray gun comparison, where the listings state the tip and cup sizes up front. For high-volume production spraying, pick the conventional side, where the Binks 2100 pressure feed gun and its 14-inch fan pattern fit large surfaces.

A fender needs a fresh coat, or a gate needs primer before winter, and the gun on the end of the air hose decides how the paint lands. This comparison puts the hvlp spray gun vs conventional spray gun question against the listings on this page: HVLP spray guns on one side and a conventional pressure feed gun on the other.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

The three spray guns

HVLP Air Spray Gun with 1.4/1.7/2mm Nozzles & Air

HVLP Air Spray Gun with 1.4/1.7/2mm Nozzles & Air

GATTLELIC9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An HVLP spray gun with 1.4, 1.7 and 2.0 mm nozzles, a 600 cc cup system, a filter regulator and stated working pressure and air consumption.

Pros

  • Three nozzles, 1.4, 1.7 and 2.0 mm, with a stated use for each
  • Working pressure of 2.5 to 3.5 bar and air consumption of 275 L/min stated in the listing
  • 10 disposable 600 cc cups and a filter regulator in the box
  • 15-hole brass hood for atomization, with a stated 240 mm spray width

Cons

  • No warranty term is stated
  • 600 cc cup is smaller than the 1000 cc cup on the BANG4BUCK example
  • Nozzle changes need the matching needle swapped too, or the gun leaks
  • Disposable cups are a consumable you keep buying
BANG4BUCK High Performance HVLP Gravity Feed Spray

BANG4BUCK High Performance HVLP Gravity Feed Spray

B4B BANG 4 BUCK9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An HVLP gravity feed spray gun with 1.4, 1.7 and 2.5 mm nozzles, a 1000 cc aluminum cup and a micrometer air regulator with gauge.

Pros

  • Three nozzles, 1.4, 1.7 and 2.5 mm, for base coats through thick primers
  • 1000 cc aluminum cup, the largest cup stated here
  • Micrometer air regulator with gauge in the box
  • Control knobs for spray pattern, fluid control and air pressure

Cons

  • No warranty term is stated
  • No working pressure or air consumption in the listing
  • The pre-installed nozzle may need effort to remove
  • No spray width or spraying distance stated
Binks 2100 Paint Spray Gun 2101-2800-7 63BSS 63PB

Binks 2100 Paint Spray Gun 2101-2800-7 63BSS 63PB

Binks9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A conventional pressure feed spray gun with a 1.2 mm stainless steel nozzle, a 14-inch fan pattern and an in-handle air control valve.

Pros

  • Pressure feed delivery for high-volume output in production work
  • 1.2 mm stainless steel fluid nozzle resists solvents and coatings
  • 14-inch fan pattern for fast coverage on large surfaces
  • In-handle air control valve adjusts airflow without stopping work

Cons

  • No cup or pressure pot stated, so the feed setup is unclear
  • No air consumption or working pressure stated
  • 1.2 mm nozzle suits low-to-medium viscosity only
  • One nozzle size only, with no spare tips stated in the box

Other welders and gear to compare

Side by side

GATTLELIC HVLP Spray Gun BANG4BUCK HVLP Gravity Spray Gun Binks 2100 Conventional Spray Gun
Gear Score 60 58 57
Side HVLP HVLP Conventional
Feed Not stated Gravity feed Pressure feed
Nozzle tips 1.4, 1.7, 2.0 mm 1.4, 1.7, 2.5 mm 1.2 mm (0.046 in)
Cup 600 cc, 10 disposable cups 1000 cc aluminum Not stated
Working pressure 2.5 to 3.5 bar Not stated Not stated
Air consumption 275 L/min Not stated Not stated
Spray width 240 mm Not stated 14 in fan pattern
Air control Filter regulator Micrometer regulator with gauge In-handle air control valve
Warranty Not stated Not stated Not stated

Treat the specs as maker ratings pulled straight from the listings; we gathered them on 19 November 2026. No listing states a safety listing or a warranty term.

HVLP spray gun vs conventional spray gun: feed and air

The feed is the first split. The BANG4BUCK is a gravity feed HVLP gun, with a 1000 cc aluminum cup that feeds paint down to the nozzle. The Binks 2100 is a conventional pressure feed gun, with paint pushed to the gun under pressure for consistent, high-volume output. The GATTLELIC listing states a 600 cc cup system with disposable cups but does not name its feed type.

Air is the second split, and only one listing gives numbers. The GATTLELIC states a working pressure of 2.5 to 3.5 bar and air consumption of 275 L/min, with a 1/4-inch NPT inlet. The BANG4BUCK and Binks listings state no working pressure or air consumption, so neither side wins on air needs from the listings alone. See our air compressor regulator and filter setup guide before plumbing the gun in.

Nozzles and tips

Nozzle size decides which coatings each gun suits. The BANG4BUCK ships with three stainless steel nozzles, 1.4, 1.7 and 2.5 mm, and the listing names base coats, clear coats and high-viscosity coatings such as high-build primers, thick enamels and gel coats among its uses. The GATTLELIC ships with 1.4, 1.7 and 2.0 mm nozzles, and pairs the 1.4 mm tip with topcoats, the 1.7 mm tip with primers and the 2.0 mm tip with large areas. The Binks has a single 1.2 mm stainless steel nozzle with a 0.046-inch orifice, and the listing optimizes it for low-to-medium viscosity coatings. The 2.5 mm tip is the widest stated here.

Cups and paint supply

The BANG4BUCK cup is a 1000 cc aluminum cup, the largest cup stated here. The GATTLELIC uses a 600 cc cup system with 10 disposable cups and lids in the box, so cleaning means swapping a cup instead of washing one. The Binks is a pressure feed gun, and its listing states no cup or pressure pot, so the feed setup is unclear from the listing alone.

Handling and what is in the box

The Binks example has an in-handle air control valve that lets airflow change without stopping work. The GATTLELIC listing adds a brush, a wrench and sealing tape in the box, and the BANG4BUCK listing adds an adjustment wrench.

Warranty

No listing here states a warranty term. The GATTLELIC listing invites buyers to contact its service team with problems, but it states no term in years or months. The BANG4BUCK and Binks listings state no warranty at all. A missing warranty term is a gap in all three listings.

Choose the HVLP side if

  • You spray primers, base coats and clear coats and want the tip sizes stated.
  • You want a cup system with disposable cups to skip washing the cup.
  • You want the largest cup stated here, the 1000 cc aluminum cup.
  • You want the working pressure and air consumption stated before you buy.

Choose the conventional side if

  • You spray large surfaces at production volume.
  • You spray conventional coatings, primers and high-solids materials.
  • You want a 14-inch fan pattern for fast coverage.
  • You want stainless steel fluid passages for solvent-based materials.

FAQ for welders

What size air compressor do I need for an HVLP spray gun?

The GATTLELIC listing states a working pressure of 2.5 to 3.5 bar and air consumption of 275 L/min, so match the compressor to those figures. The BANG4BUCK listing states no working pressure or air consumption, so its air needs are unclear from the listing. See our best quiet air compressor guide for shop options.

What size air hose fits an HVLP spray gun?

The GATTLELIC listing states a 1/4-inch NPT inlet, so the hose fitting must match that thread. The BANG4BUCK listing states a barbed tail but no inlet size. See our best air compressor hose guide for hose options.

Which HVLP spray gun here suits automotive paint?

Both HVLP listings name automotive paint. The GATTLELIC listing names car painting, primers, topcoats and detail coats, and the BANG4BUCK listing names auto paint, base coats and clear coats. Pick the tip set that matches the coating: the GATTLELIC pairs its 1.4 mm tip with topcoats and its 1.7 mm tip with primers.

What tips do I need for primer and topcoat?

The GATTLELIC listing pairs its 1.7 mm tip with primers and its 1.4 mm tip with topcoats. The BANG4BUCK listing names high-build primers and thick coatings among its uses, along with base coats and clear coats. The Binks has a single 1.2 mm nozzle for low-to-medium viscosity coatings.

Do HVLP spray guns use less paint than conventional guns?

The GATTLELIC listing claims the gun saves 20% of paint with utilization up to 65%, but those are the maker claims, not a rated figure. The BANG4BUCK and Binks listings state no paint utilization figure, so the listings alone cannot settle the comparison. Compare the stated tips, cups and fan patterns instead.

Related: best low cost HVLP spray gun, HVLP vs powder coating gun, best air compressor hose, and the metal finishing hub. Also see our air compressor regulator and filter setup guide.

Scoring, line by line

All three guns are scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. No listing states a safety listing or a warranty term, so those two score zero for all three.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
GATTLELIC HVLP Spray Gun 9.6 30 21 21 n/a 0
BANG4BUCK HVLP Gravity Spray Gun 9.6 29 21 20 n/a 0
Binks 2100 Conventional Spray Gun 9.6 28 22 19 n/a 0

Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score. Safety points apply to gear that runs on power or lists safety features. Without either, we score out of 90 instead of 100.

Before you spray. Check the pre-installed nozzle is tight before first use, and match the air fitting to the 1/4-inch NPT inlet on the GATTLELIC example. Set the regulator before pulling the trigger, and check the filter is clean. Spray with ventilation, wear a respirator and eye protection, and keep the gun away from ignition sources. See our Safety Disclaimer.

More buying guides

Coating and Polishing ·

Best Hvlp Spray Gun Cleaning Kit (2026)

Five spray gun cleaning kits compared on piece count, brush types, needles, storage and the warranty each listing states.