Best HVLP Spray Gun Kit with 1.4/1.7/2.0/2.5 mm Nozzles (2026): 5 Picks Compared
Five HVLP spray gun kits compared on stated nozzle sets, cup size, working pressure, air use and warranty, for primer, base coat and clear coat work on metal.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallZeinlenx 827-4 Nozzle9.7/10View on Amazon - 2
Best Disposable Cup SystemZeinlenx 208 Cup System9.7/10View on Amazon - 3
Highest Stated Transfer RateBENTOHKLE 8199.6/10View on Amazon - 4
Best for Small Area WorkPNTGREEN W400-P9.4/10View on Amazon
Paint day in a home shop usually starts with parts on stands, primer mixed and a compressor humming in the corner, and the gun in your hand decides whether the coat lays flat or turns to orange peel. That job is where the best hvlp spray gun kit with 1.4/1.7/2.0/2.5 mm nozzles earns its keep, because nozzle size, cup setup and air use change with every coat from primer to clear.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall Zeinlenx 827-4 Nozzle: The full stated 1.4/1.7/2.0/2.5 mm nozzle set, a 1000cc aluminum cup and a 1 year warranty. Check price on Amazon
- Best Disposable Cup System Zeinlenx 208 Cup System: The full stated nozzle set with a 600 ml disposable cup system, 10 liners and a pressure gauge. Check price on Amazon
- Highest Stated Transfer Rate BENTOHKLE 819: A stated paint utilization rate of up to 70%, with an air regulator and oil-water separator. Check price on Amazon
- Best for Small Area Work PNTGREEN W400-P: A 1.3/1.5/1.7 mm set with a stated spray width of 100-250 mm for touch-ups and small areas. Check price on Amazon
The machines

Zeinlenx HVLP Gravity Feed Spray Gun Kit
An HVLP gravity feed kit with the full 1.4/1.7/2.0/2.5 mm nozzle set, a 1000cc aluminum cup and a 1 year warranty stated by the maker.
Pros
- Full stated nozzle set at 1.4/1.7/2.0/2.5 mm, with the 1.4 mm nozzle attached
- 1000cc aluminum cup, the largest stated cup volume here
- Brass air cap with stainless steel needle and nozzle as stated by the maker
- 1 year warranty stated by the maker
Cons
- Working pressure is not stated by the maker
- Air use in cfm is not stated by the maker
- Pre-installed nozzle may need effort to remove, as stated by the maker
- Needs an air compressor, as stated by the maker

Zeinlenx HVLP Spray Gun Kit
An HVLP kit with the full 1.4/1.7/2.0/2.5 mm nozzle set, a 600 ml disposable cup system and a stated pressure range of 2.5-3.5 bar.
Pros
- Full stated nozzle set at 1.4/1.7/2.0/2.5 mm
- 600 ml disposable cup system with 10 disposable cup liners
- Stated working pressure at 2.5-3.5 bar with a pressure gauge included
- 15-hole copper atomizer with a stated paint utilization rate of 65%
Cons
- Stated spray width is 240mm, below the 260 mm top end stated for the SRQLNTT 819
- Disposable liners are consumables, with 10 liners in the kit
- Stated pressure range starts at 2.5 bar, above the 2.0 bar start of other kits here
- Air use is stated at 275L/min, so check your compressor against that figure

BENTOHKLE 819 HVLP Air Spray Gun Kit
An 819 HVLP kit with 1.4/1.7/2.0 mm nozzles, an air regulator and oil-water separator, and a stated paint utilization rate of up to 70%.
Pros
- Stated paint utilization rate of up to 70%, the highest stated rate here
- Air regulator and oil-water separator included as stated by the maker
- 15 hole brass atomization cap as stated by the maker
- Stated air use at 3.0-3.9 cfm and working pressure at 2.0-3.5 bar
Cons
- No 2.5 mm nozzle in the stated 1.4/1.7/2.0 mm set
- No warranty term is stated by the maker
- Cup volume is not stated by the maker
- Spray distance is stated at 200-300 mm, so plan your pass distance around it

819 HVLP Air Spray Gun Kit with 1.4/1.7/2.0mm
An 819 HVLP kit with 1.4/1.7/2.0 mm nozzles, 10 x 650ml mixing cups and an integrated air regulator stated by the maker.
Pros
- Integrated air regulator as stated by the maker
- 10 x 650ml mixing cups included as stated by the maker
- Stated spray width of 160-260 mm at 2.0-3.5 bar
- Stated paint utilization of approximately 65% with air use at 3.0-3.9 cfm
Cons
- No 2.5 mm nozzle in the stated 1.4/1.7/2.0 mm set
- Stated paint utilization is approximately 65%, below the up to 70% stated for the BENTOHKLE 819
- Mixing cups are separate from the gun cup setup, so plan your mixing step
- Stated spray width tops out at 260 mm

PNTGREEN HVLP Spray Gun Kit Air Paint Sprayer
An HVLP kit with 1.3/1.5/1.7 mm nozzles, a 600 CC paint cup, an air regulator valve and an oil-water separator stated by the maker.
Pros
- Air regulator valve and oil-water separator included as stated by the maker
- 600 CC paint cup with a cleaning kit in the stated accessories
- 360 degree adjustable nozzle with 3 spray patterns as stated by the maker
- Stated spray width of 100-250 mm for small area painting
Cons
- No 2.0 mm or 2.5 mm nozzle in the stated 1.3/1.5/1.7 mm set
- Air use in cfm is not stated by the maker
- Stated spray width starts at 100 mm, the narrowest stated range here
- No warranty term is stated by the maker
Other welders and gear to compare
Zeinlenx HVLP Gravity Feed Spray Gun Kit withCheck price on Amazon
Zeinlenx HVLP Automotive Spray Gun KitCheck price on Amazon
Zeinlenx HVLP Spray Gun KitCheck price on Amazon
Professional HVLP Spray Gun Kit Air Spray Gun with 1.7Check price on Amazon
HVLP Spray Gun Kit with 1.4/1.7/2.0/2.5mm Nozzles & AirCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Nozzles | Cup | Working pressure | Air use | Warranty |
|---|---|---|---|---|---|---|
| Zeinlenx 827-4 Nozzle | 9.7/10 | 1.4/1.7/2.0/2.5 mm | 1000cc aluminum cup | Not stated | Not stated | 1 year |
| Zeinlenx 208 Cup System | 9.7/10 | 1.4/1.7/2.0/2.5 mm | 600 ml disposable cup system | 2.5-3.5 bar | 275L/min | Not stated |
| BENTOHKLE 819 | 9.6/10 | 1.4/1.7/2.0 mm | Not stated | 2.0-3.5 bar | 3.0-3.9 cfm | Not stated |
| SRQLNTT 819 | 9.5/10 | 1.4/1.7/2.0 mm | 10 x 650ml mixing cups | 2.0-3.5 bar | 3.0-3.9 cfm | Not stated |
| PNTGREEN W400-P | 9.4/10 | 1.3/1.5/1.7 mm | 600 CC paint cup | 2.0-3.5 Bar | Not stated | Not stated |
All specs here repeat what the maker rates and the listing prints, copied down 20 November 2026.
Buying guide: best hvlp spray gun kit with 1.4/1.7/2.0/2.5 mm nozzles
Nozzle sets
Only the Zeinlenx 827-4 Nozzle and the Zeinlenx 208 Cup System state the full set in the keyword, at 1.4/1.7/2.0/2.5 mm. The BENTOHKLE 819 and the SRQLNTT 819 state 1.4/1.7/2.0 mm sets, with no 2.5 mm nozzle in the stated set. The PNTGREEN W400-P states a 1.3/1.5/1.7 mm set, so it covers smaller nozzle sizes and leaves the 2.0 mm and 2.5 mm sizes out of its stated set. Check the stated set against the coatings you spray before you buy.
Working pressure and air use
The SRQLNTT 819, BENTOHKLE 819 and PNTGREEN W400-P state a working pressure of 2.0-3.5 bar, and the Zeinlenx 208 Cup System states 2.5-3.5 bar. Air use is stated at 3.0-3.9 cfm for the SRQLNTT 819 and BENTOHKLE 819, and at 275L/min for the Zeinlenx 208 Cup System. The Zeinlenx 827-4 Nozzle and PNTGREEN W400-P do not state air use, so match your compressor to the stated figures where they are given and check the manual where they are not.
Cups and cleanup
Cup setups differ across these kits. The Zeinlenx 827-4 Nozzle states a 1000cc aluminum cup, the PNTGREEN W400-P states a 600 CC paint cup, and the Zeinlenx 208 Cup System states a 600 ml disposable cup system with 10 disposable cup liners. The SRQLNTT 819 includes 10 x 650ml mixing cups as stated in its title. Disposable liners cut cleanup time between coats, while a fixed aluminum cup holds more paint per fill at 1000cc.
Regulators and separators
The SRQLNTT 819 states an integrated air regulator, the BENTOHKLE 819 includes an air regulator and an oil-water separator, and the PNTGREEN W400-P includes an air regulator valve and an oil-water separator. The Zeinlenx 208 Cup System includes a pressure gauge and a 1/4 inch NPT inlet with a quick adapter. The Zeinlenx 827-4 Nozzle states that the gun needs to be connected to an air compressor, and its pre-installed nozzle may need effort to remove.
Before You Strike an Arc
- Confirm your compressor can supply the stated air use where it is given, at 3.0-3.9 cfm or 275L/min, before the first coat.
- Check the nozzle set in the box on arrival against the stated sizes, from 1.3/1.5/1.7 mm up to 1.4/1.7/2.0/2.5 mm.
- Set the regulator and pattern controls to the stated working pressure range for your kit, then check the manual for your coating.
- Spray in a ventilated area and follow the paint maker directions for respirator and eye protection.
FAQ for welders
What is the best hvlp spray gun here?
The Zeinlenx 827-4 Nozzle ranks at the top here because it states the full 1.4/1.7/2.0/2.5 mm nozzle set, a 1000cc aluminum cup and a 1 year warranty. The Zeinlenx 208 Cup System also states the full nozzle set, with a 600 ml disposable cup system.
How do you set an hvlp spray gun?
Start from the stated working pressure for your kit, at 2.0-3.5 bar for the SRQLNTT 819, BENTOHKLE 819 and PNTGREEN W400-P, and at 2.5-3.5 bar for the Zeinlenx 208 Cup System. Then adjust fluid, pattern and air controls as the maker describes, and check the manual for your coating.
What is an hvlp paint gun?
HVLP stands for High Volume Low Pressure, as the BENTOHKLE 819 maker spells out. These kits use a high volume of air at low pressure to atomize paint, with stated paint utilization rates from up to 60% to up to 70% across the kits here.
How does an hvlp spray gun work?
Air from a compressor passes through the gun body and air cap, drawing paint from the cup and breaking it into droplets at the nozzle. The kits here state spray widths from 100-250 mm on the PNTGREEN W400-P to 160-260 mm on the SRQLNTT 819.
How much cfm do I need for an hvlp spray gun?
The SRQLNTT 819 and BENTOHKLE 819 state air use at 3.0-3.9 cfm, and the Zeinlenx 208 Cup System states air consumption at 275L/min. The Zeinlenx 827-4 Nozzle and PNTGREEN W400-P do not state air use, so check the manual for those kits.
Related: metal finishing, best hvlp spray gun for automotive paint, hvlp spray gun vs conventional spray gun, and coating and polishing. Also see our best low cost hvlp spray gun and hvlp vs powder coating gun.
Scoring, line by line
Each kit is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. No kit here states a safety standard such as CSA or UL, so every kit scores zero on that criterion, and only the Zeinlenx 827-4 Nozzle states a warranty term, at 1 year.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Zeinlenx 827-4 Nozzle | 9.7 | 29 | 21 | 20 | n/a | 3 |
| Zeinlenx 208 Cup System | 9.7 | 32 | 22 | 22 | n/a | 0 |
| BENTOHKLE 819 | 9.6 | 28 | 20 | 20 | n/a | 0 |
| SRQLNTT 819 | 9.5 | 27 | 20 | 20 | n/a | 0 |
| PNTGREEN W400-P | 9.4 | 23 | 19 | 19 | n/a | 0 |
A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number. Where safety does not apply (unpowered gear with no listed safety features), it is left out and the remaining 90 points make up the score.




