308 Welding Rod vs 309: Which One Do You Need?
308 welding rod vs 309: which rod for stainless to stainless and which for dissimilar joints, how to read the rod name, and three 308 rods ranked.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
SS TIGView on Amazon - 2
YESWELDER Stainless Steel TIG Welding Rod ER308L 1/16"x16"View on Amazon - 3
YESWELDER Stainless Steel TIG Welding Rod ER308L 1/8"x16" 5LBView on Amazon - 4
ARCCAPTAIN Stainless Steel TIG Welding Rod ER308LView on Amazon - 5
E308L-16 Arc Welding Rod Stainless Steel ElectrodesView on Amazon - 6
Forney 30301 E6013 Welding RodView on Amazon
308 welding rod vs 309 comes down to what you are joining: 308 is the rod for welding stainless steel to itself, like 304 to 304, while 309 is the rod for dissimilar joints, like stainless steel to carbon steel, and for stainless grades you cannot identify. All three rods in this guide are 308: two ER308L TIG rods and one E308L-16 stick electrode, so the gear section shows the 308 side in detail and the comparison explains when to reach for 309 instead.
Other welders and gear to compare
SS TIGCheck price on Amazon
YESWELDER Stainless Steel TIG Welding Rod ER308L 1/16"x16"Check price on Amazon
YESWELDER Stainless Steel TIG Welding Rod ER308L 1/8"x16" 5LBCheck price on Amazon
ARCCAPTAIN Stainless Steel TIG Welding Rod ER308LCheck price on Amazon
E308L-16 Arc Welding Rod Stainless Steel ElectrodesCheck price on Amazon
Forney 30301 E6013 Welding RodCheck price on Amazon
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Affiliate disclosure.
308 welding rod vs 309: the difference in one paragraph
Welding rod numbers name the filler metal. ER308L and E308L-16 are 308 fillers: the ER prefix marks a bare electrode rod or wire (the TIG rod here), the E prefix marks a coated stick electrode, and the L marks low carbon, which the listings tie to resistance against intergranular corrosion. The 308 family matches 304, 304L, 308, 308L, 321 and 347 stainless, per both TIG listings here. 309 is the higher-alloy rod for joining stainless to carbon steel and for unknown stainless grades, where its extra alloy content keeps the weld sound across the dissimilar joint.
Side by side
| Product | Type (stated) | Diameter (stated) | Length (stated) | Pack (stated) |
|---|---|---|---|---|
| WeldingCity ER308L | TIG rod | 3/32 in | 36 in | 5 lb |
| YESWELDER ER308L | TIG rod | 1/16 in | 16 in | 5 lb |
| SÜA E308L-16 | Stick electrode | 1/8 in | 14 in | 4.4 lb |
Ratings in this table are the makers’ own claims taken from each product page (19 October 2026). All three products below are 308 rods; no 309 product is in this listing set.
When 308 is the right rod
Choose 308 when both sides of the joint are stainless. The WeldingCity listing names 304, 304L, 308, 308L, 321 and 347 as applications, and the YESWELDER listing names the same grades. The SÜA stick electrode names 304L and stabilized grades like 321 and 347. For food processing equipment, dairy and restaurant gear, chemical tanks and general stainless fabrication, the listings point at 308. The low carbon in ER308L, stated as 0.03 percent maximum on both TIG listings, is what keeps the weld resistant to intergranular corrosion.
Process decides the form. The two ER308L products here are TIG rods for the GTAW process with shielding gas, suited to clean shop work on thinner stainless. The SÜA E308L-16 is a stick electrode for all-position arc welding, the pick for field repairs and thicker sections where TIG setup is impractical.
When 309 is the right rod
Choose 309 when the joint crosses metals: stainless to carbon steel, or stainless to a grade you cannot identify. The 308 listings here name only stainless-to-stainless applications, so a dissimilar joint is outside what any of the three products covers. 309 is also the common choice for cladding and overlay work on carbon steel, where its higher alloy content survives dilution from the base metal.
When in doubt about the base metal, 309 is the safer guess: its higher alloy content tolerates dilution from carbon steel and unknown grades. But when you know both sides are stainless, 308 is the matching filler and the one the listings here support.
How to read the rod name
ER308L breaks down as: ER for electrode or rod (bare filler; the TIG rod here), 308 for the alloy, L for low carbon. E308L-16 breaks down as: E for electrode (stick), 308L for the alloy, 16 for the coating and current type. The WeldingCity listing gives the full specification as AWS A5.9/ASME SFA A5.9 with a typical deposited composition, while the YESWELDER listing states the 0.03 percent maximum carbon figure. Match the name on the rod to the name in the listing before you buy, since 308 and 309 sit side by side on the shelf.
The gear: three 308 rods ranked
The WeldingCity ER308L leads: a 5-pound pack of 3/32 by 36 inch TIG rods with the full AWS A5.9/ASME SFA A5.9 specification and a typical deposited chemical composition stated, single-end stamped, in 0.045, 1/16, 3/32 and 1/8 inch diameters. The listing names a U.S. based supplier with strong technical support. Shielding gas is usually 100 percent argon.
The YESWELDER ER308L is the value pick: a 5-pound pack of 1/16 by 16 inch TIG rods for the same 304, 304L, 308, 308L, 321 and 347 grades, with 100 percent argon or argon/helium for greater penetration and higher speeds. The listing names welding, petrochemical, pressure vessels, food processing machinery and medical equipment as applications.
The SÜA E308L-16 is the stick pick: a 4.4-pound pack of 1/8 by 14 inch electrodes for all-position welding, with easy strike and restrike, smooth arc action, low spatter and a self-peeling slag. The listing states a finely rippled bead and names dairy, food, restaurant equipment and chemical tanks as applications. Check the listing’s quantity picture for the approximate electrode count per pound.
FAQ for welders
Can I use 308 on carbon steel?
308 is for stainless-to-stainless joints. For stainless to carbon steel, 309 is the rod made for the dissimilar joint.
What does the L in 308L mean?
Low carbon. Both TIG listings here state 0.03 percent maximum carbon, which the listings tie to resistance against intergranular corrosion in the weld.
What is the difference between ER308L and E308L-16?
ER308L is a bare TIG rod used with shielding gas; E308L-16 is a coated stick electrode for arc welding. The SÜA listing here is the stick electrode of the three.
What gas do I need for ER308L?
The WeldingCity listing states usually 100 percent argon. The YESWELDER listing states 100 percent argon or argon/helium for greater penetration and higher speeds.
Can I use 309 on stainless to stainless?
It will weld, but 308 is the matching filler for stainless-to-stainless joints and the listings here cover only 308. Save 309 for dissimilar joints and unknown grades.
How do I choose the diameter?
The WeldingCity listing offers 0.045, 1/16, 3/32 and 1/8 inch; the YESWELDER is 1/16 inch; the SÜA is 1/8 inch with 3/32 also available. Match the diameter to the material thickness and the joint.
Related: browse our welder hub and the welding consumables hub for more filler and machine guides.




