Best Welding Rod for Vertical Welding (2026)
Four stick electrodes for vertical welding, compared on diameter, pack weight, positions and power, from a fast-freezing E6011 to a hardfacing rod.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallPGN E60119.5/10View on Amazon - 2
Galvanized RepairRockmount Tartan B9.5/10View on Amazon - 3
Easiest StartsArcomin E60139.4/10View on Amazon - 4
Hardfacing PickForney Supercote Hardfacing9.3/10View on Amazon
Picture a joint that runs straight up a post, with the puddle fighting gravity every inch of the way. That is the job this guide is for, and the best welding rod for vertical welding is the rod whose flux freezes fast enough to hold the bead in place. Stick electrodes are compared here on what each listing states: diameter, pack weight, welding positions and power, plus the warranty where a term is stated.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall PGN E6011: Fast-freezing flux for vertical and overhead work, all-position, AC/DC, in a 10 lb pack. Check price on Amazon
- Galvanized Repair Rockmount Tartan B: Welds through dirt, oil and rust on mild steel and galvanized steel, in vertical and overhead positions. Check price on Amazon
- Easiest Starts Arcomin E6013: Easy arc starts with minimal spatter and self-releasing slag, suited to vertical-down welds. Check price on Amazon
- Hardfacing Pick Forney Supercote Hardfacing: Hardfacing rod for worn parts, RC 52-58 hardness, with a stated 90 day warranty. Check price on Amazon
The machines

PGN E6011 Welding Rod 3/32" 10LB
A 3/32 inch E6011 rod in a 10 lb pack, with fast-freezing flux for vertical and overhead work, AC/DC power and deep penetration on dirty or rusty steel.
Pros
- Fast-freezing flux holds the bead on vertical and overhead joints
- Works in all positions, from flat to overhead
- Runs on AC and DC power sources
- Deep penetration on dirty or rusty surfaces
Cons
- Only a 3/32 inch diameter is listed
- A 10 lb pack may be more than a small repair needs
- No warranty term is stated
- Fast-freezing flux suits out-of-position work, not flat production runs

Rockmount Tartan B Welding Electrode: 3/32" Dia.
A 3/32 inch Tartan B electrode in a 1 lb pack, made for mild steel and galvanized repair, with deep penetration and vertical and overhead positions.
Pros
- Deep penetration with clean, non-porous welds, per the maker
- Welds through dirt, oil, paint and rust
- Suits galvanized steel as well as mild steel
- Works in vertical and overhead positions
Cons
- Only a 1 lb pack is listed
- Only a 3/32 inch diameter is listed
- No warranty term is stated
- Galvanized steel work needs care with fumes and ventilation

Arcomin E6013 3/32" Welding Rods 2LB
A 3/32 inch E6013 rod in a 2 lb pack, with easy arc starts, minimal spatter and self-releasing slag, listed for all positions including vertical-down welds.
Pros
- Easy arc starts with minimal spatter
- Self-releasing slag suits vertical-down welds
- Runs on AC/DC machines, including low-voltage AC setups
- Moisture-resistant packaging for long-term storage
Cons
- Only a 2 lb pack is listed
- Shallow penetration suits poorly fitted joints, not deep groove work
- Aimed at light fabrication and thin metal, not heavy plate
- Carbon steel only; not listed for galvanized steel

Forney 42401 Supercote Hardfacing Welding Rod
A 5/32 inch hardfacing rod in a 1 lb pack, for surface buildup on worn machine parts, with RC 52-58 hardness and a stated 90 day warranty.
Pros
- RC 52-58 hardness for moderate abrasion work
- Crack resistant weld, per the maker
- Smooth arc action with easy slag removal
- Stated 90 day warranty against manufacturer defects
Cons
- Hardfacing only; not a general-purpose vertical rod
- A 5/32 inch diameter is the largest here, less suited to thin metal
- Suits moderate abrasion and low impact only
- Only a 1 lb pack is listed
Other welders and gear to compare
Forney 30301 E6013 Welding RodCheck price on Amazon
YESWELDER TIG Tungsten Electrode Pre-Sharpened WeldingCheck price on Amazon
ARCCAPTAIN Stainless Steel TIG Welding Rod ER308LCheck price on Amazon
ATLASWELDER 6011 Welding Rod 1/8" 5LBCheck price on Amazon
ARCCAPTAIN E7018 Welding Rod 3/32" 10LB Low Hydrogen CarbonCheck price on Amazon
ATLASWELDER 6013 Welding Rod 1/8" 10LBCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Diameter | Pack weight | Positions | Power | Warranty |
|---|---|---|---|---|---|---|
| PGN E6011 | 9.5/10 | 3/32 in | 10 lb | All positions | AC/DC | None stated |
| Rockmount Tartan B | 9.5/10 | 3/32 in | 1 lb | Vertical and overhead | Not stated | None stated |
| Arcomin E6013 | 9.4/10 | 3/32 in | 2 lb | All positions | AC/DC | None stated |
| Forney Supercote Hardfacing | 9.3/10 | 5/32 in | 1 lb | All positions | Not stated | 90 days |
Ratings in this table are the makers’ own claims taken from each product page (18 November 2026).
Buying guide: best welding rod for vertical welding
Fast-freezing flux
Vertical welding is a fight against gravity, and flux that freezes fast helps the bead stay where it belongs. The PGN E6011 lists a fast-freezing flux formula for precise control in vertical and overhead welding, aimed at preventing drips. The Arcomin E6013 lists a refined flux coating with self-releasing slag, suited to vertical-down welds.
Diameter
The PGN, Rockmount and Arcomin rods are 3/32 inch, while the Forney is 5/32 inch. A 3/32 inch rod suits thinner material and tighter joints. The Forney 5/32 inch rod is a heavier rod for buildup work on worn parts.
Pack weight
The PGN pack holds 10 lb, the Arcomin 2 lb, and the Rockmount and Forney 1 lb each. A 10 lb pack suits a shop that burns rods often, while a 1 lb pack suits a single repair.
Power supply
The PGN E6011 and the Arcomin E6013 list AC/DC power, and the Arcomin also lists low-voltage AC setups. The Rockmount and Forney listings do not state a power type, so check that the rod suits the machine on hand before ordering.
Hardfacing is a different job
The Forney 42401 is a hardfacing rod, not a general joining rod. The maker lists it for surface buildup on new or worn machine parts of cast steel and manganese steel, with RC 52-58 hardness for moderate abrasion and low impact work. If the job is joining steel in a vertical position, the other picks fit better. If the job is building up a worn surface, the Forney is the only pick here made for it. For shielding gas on MIG work instead, see our argon vs C25 gas for MIG welding comparison.
Use as directed. Keep rods dry and stored as the maker directs, since damp rods weld poorly. The Arcomin lists moisture-resistant packaging for long-term storage. Galvanized steel gives off fumes when welded, so work with ventilation and keep the breathing zone clear. Keep the area clear of anything that can burn, and never exceed the stated load or rating of any part of the setup.
Before You Strike an Arc
- Check the power supply: the PGN and Arcomin list AC/DC, so confirm the other rods suit the machine on hand.
- Check rod diameter against the joint: the PGN, Rockmount and Arcomin rods are 3/32 inch and the Forney is 5/32 inch.
- Check pack weight on arrival: the PGN pack holds 10 lb, the Arcomin 2 lb, and the Rockmount and Forney 1 lb each.
- Check the work: the Rockmount lists welding through dirt, oil, paint and rust, and galvanized steel needs ventilation.
FAQ for welders
Which rod is best for vertical welding?
The PGN E6011 leads this set for vertical work. The maker lists fast-freezing flux for precise control in vertical and overhead welding, all-position flexibility and AC/DC power, plus deep penetration on dirty or rusty surfaces.
Can you weld vertical with E6013?
Yes, the Arcomin E6013 lists all-position welding, including flat, vertical, overhead and horizontal work. The maker lists easy arc starts, minimal spatter and self-releasing slag, aimed at vertical-down welds, and AC/DC power including low-voltage AC setups.
What diameter rod should I use for vertical welding?
The PGN, Rockmount and Arcomin rods here are 3/32 inch, and the Forney is 5/32 inch. A 3/32 inch rod suits thinner material and tighter joints, while the 5/32 inch Forney is a heavier rod for buildup work.
Does a hardfacing rod work for vertical welding?
The Forney 42401 lists all positions, so it can run vertical, but hardfacing is a different job from joining steel. The maker lists it for surface buildup on worn machine parts, with RC 52-58 hardness for moderate abrasion and low impact work.
Do I need AC or DC for these rods?
The PGN E6011 and the Arcomin E6013 list AC/DC power, so they suit either supply. The Rockmount and Forney listings do not state a power type, so check that the rod suits the machine on hand.
Related: vertical stick welding tips, 6011 welding rod uses, 6013 welding rod uses, welding rods types, stick welding tips and tricks, hardfacing welding rod types, best welding rod storage, and the welding consumables hub.
Scoring, line by line
Each rod is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. Welding rods carry no electrical safety listing in these listings, so every rod here scores zero on that criterion; the ranking comes from the other four.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| PGN E6011 | 9.5 | 32 | 21 | 21 | 0 | 0 |
| Rockmount Tartan B | 9.5 | 30 | 21 | 19 | 0 | 0 |
| Arcomin E6013 | 9.4 | 28 | 20 | 20 | 0 | 0 |
| Forney Supercote Hardfacing | 9.3 | 24 | 20 | 18 | 0 | 1 |
The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure.




