Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Stick Welding Tips and Tricks for Cleaner Beads

Dry rods, the right electrode for the steel, and a steady arc are what turn rough stick beads into clean ones.

Stick Welding Tips and Tricks for Cleaner Beads
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1ARCCAPTAIN E7018 Welding Rods 1/8" 5LB LowARCCAPTAIN E7018 Welding Rods 1/8" 5LB Low9.5/10View on Amazon
  2. 2YESWELDER 15lb Welding Rod Oven 110V TemperatureYESWELDER 15lb Welding Rod Oven 110V Temperature9.5/10View on Amazon
  3. 3ATLASWELDER 6013 Welding Rod 1/8" 10LBATLASWELDER 6013 Welding Rod 1/8" 10LB9.5/10View on Amazon
  4. 4YESWELDER UPGRADED Rutile Material E6013 3/32''YESWELDER UPGRADED Rutile Material E6013 3/32''9.4/10View on Amazon

A gate frame that needs a fresh bead, a cracked bracket on a trailer, a mower deck with a split seam. Stick welding handles that kind of repair, and the bead shows every shortcut: damp rods, the wrong electrode for the steel, an arc that wanders. These stick welding tips and tricks cover the habits that clean up the bead, from keeping rods dry to matching the electrode to the joint.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

ARCCAPTAIN E7018 Welding Rods 1/8" 5LB Low

ARCCAPTAIN E7018 Welding Rods 1/8" 5LB Low

ARCCAPTAIN9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1/8 in E7018 low hydrogen rod in a 5 lb pack, made for structural steel and all position welding.

Pros

  • Low hydrogen E7018 rod for X-ray quality welds
  • Runs in any position on AC or DC reverse polarity
  • Smooth, stable arc with less spatter
  • Suits low, medium and high carbon steels and structural work

Cons

  • A 5 lb pack is small for long structural jobs
  • Low hydrogen rods need dry storage, and no oven is in the box
  • Only the 1/8 in diameter is in this pack
  • No warranty term is stated
YESWELDER 15lb Welding Rod Oven 110V Temperature

YESWELDER 15lb Welding Rod Oven 110V Temperature

YESWELDER9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 110V rod oven that holds up to 15 lb of 14 in electrodes and keeps them dry at 85 to 300 degrees F.

Pros

  • Holds up to 15 lb of rods 14 in or shorter
  • Temperature control from 85 to 300 degrees F for E6010, E6011, E6013 and E7018 rods
  • Weighs under 8 lb with a handle, so it moves around the shop
  • Wide opening lid and easy grip handle allow access while wearing gloves

Cons

  • No rods are in the box, so electrodes are a separate buy
  • The maker warns against extended unattended use over 8 hours
  • 110V only, so it needs a mains outlet nearby
  • A 15 lb capacity suits a day of welding, not bulk rod storage
ATLASWELDER 6013 Welding Rod 1/8" 10LB

ATLASWELDER 6013 Welding Rod 1/8" 10LB

ATLAS WELDER9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1/8 in E6013 rod in a 10 lb pack, made for all position welding on mild steel.

Pros

  • Smooth arc with minimal spatter and fast slag removal
  • All position welding: flat, horizontal, vertical and overhead
  • Suits automotive repairs, gates, railings, sheet metal, home projects, maintenance and fabrication
  • A 10 lb pack gives more rod than the 5 lb packs here

Cons

  • General purpose E6013, not a low hydrogen rod for structural joints
  • No warranty term is stated
  • Only the 1/8 in diameter is in this pack
  • A 10 lb pack needs dry storage, and no oven is in the box
YESWELDER UPGRADED Rutile Material E6013 3/32''

YESWELDER UPGRADED Rutile Material E6013 3/32''

YESWELDER9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3/32 in rutile E6013 rod in a 5 lb pack, made for light gauge metal, sheet metal and duct work.

Pros

  • Rutile rod with a stable arc and low spatter
  • Virtually self cleaning slag in vertical down fillets
  • Runs on AC or DC and suits low voltage AC machines
  • Made for light gauge metal, sheet metal and duct work

Cons

  • A 5 lb pack is small for long fabrication jobs
  • A 3/32 in rod suits thin metal, not thick plate
  • Only the 3/32 in diameter is in this pack
  • Light gauge focus means it is not the rod for heavy structural steel

Stick welding tips and tricks that clean up the bead

Clean beads come from habits, not luck. The tips below use the rods and the oven in this guide, and each tip ties to a step in the weld.

  • Keep rods dry. Moisture spoils a low hydrogen deposit, so store E7018 rods dry and warm them in a rod oven before welding.
  • Match the rod to the steel. E7018 low hydrogen rod suits structural steel and load bearing joints, while E6013 rutile rod suits light gauge metal, sheet metal and duct work.
  • Pick the diameter for the metal. A 1/8 in rod suits heavier joints, while a 3/32 in rod suits thin metal and sheet work.
  • Hold a steady arc. A stable arc and a steady hand keep the bead even, while a wandering arc leaves spatter and an uneven bead.
  • Chip slag between passes. Slag left on the bead spoils the next pass, so chip it off and brush the joint clean before welding over it.
  • Set the polarity the rod calls for. E7018 runs on AC or DC reverse polarity, and E6013 runs on AC or DC, so set the machine to the polarity the rod calls for.

Pick the rod for the joint

E7018 and E6013 are the rods in this guide, and each suits its own work. E7018 is the low hydrogen rod for structural steel, load bearing joints and X-ray quality welds, while E6013 is the general purpose rod for mild steel, repairs and light fabrication. Diameter follows the metal: 1/8 in rod for heavier joints, 3/32 in rod for thin metal and sheet work. The best 7018 welding rod guide scores low hydrogen picks, and the best 7018 welding rod for home shop guide covers the same rods for a home shop.

Side by side

Product Type Size Capacity Use
ARCCAPTAIN E7018 E7018 low hydrogen rod 1/8 in by 14 in 5 lb pack Structural steel
YESWELDER Rod Oven Rod oven Holds 14 in rods 15 lb Drying electrodes
ATLASWELDER E6013 E6013 rod 1/8 in by 14 in 10 lb pack All position welding
YESWELDER E6013 E6013 rutile rod 3/32 in by 14 in 5 lb pack Light gauge metal

The table shows the spread: E6013 rods for general work, an E7018 rod for structural joints, and an oven that keeps stored rods dry.

The gear for these stick welding tips and tricks

Each tip above needs gear that does its part: dry rods for a sound bead, the right electrode for the steel, and an oven that keeps low hydrogen rods dry.

Keep rods dry

The YESWELDER oven holds up to 15 lb of rods 14 in or shorter and sets the temperature from 85 to 300 degrees F with a knob. The maker lists it for E6010, E6011, E6013 and E7018 rods, and it keeps stored rods dry, which protects the low hydrogen deposit of E7018 rods. It weighs under 8 lb, runs on 110V, and carries by its handle from the workshop to the garage or an outdoor site. The maker warns against leaving it running unattended for over 8 hours or overnight.

Dry rods and clear air. Weld with ventilation or outdoors with your head out of the plume, keep flammables clear of the work, and wear a helmet, gloves and a jacket.

For more options, see our guides guides.

FAQ for welders

Which stick welding rod should a beginner start with?

E6013 is the forgiving start. The YESWELDER E6013 3/32 in rutile rod runs on AC or DC, suits low voltage AC machines, and the maker calls out light gauge metal, sheet metal and duct work. The ATLASWELDER E6013 1/8 in rod covers heavier mild steel repairs with a smooth arc and fast slag removal. Start with E6013 on practice joints, then move to E7018 when the work turns structural.

Do 7018 rods need to stay dry?

Yes. E7018 is a low hydrogen rod, and moisture spoils the low hydrogen deposit and risks cracked welds. The maker calls its E7018 a low hydrogen electrode for X-ray quality welds, and the YESWELDER oven keeps E7018 rods dry. Store rods dry and warm them in the oven before welding.

Can I weld overhead with these rods?

Yes. The ARCCAPTAIN E7018 (on Amazon) rates for welding in any position, and the ATLASWELDER E6013 rates for flat, horizontal, vertical and overhead positions. The YESWELDER E6013 3/32 in rutile rod covers all position welding too. Overhead work still needs a steady arc and clean metal, so practice the position on scrap before welding the joint.

What is the difference between 1/8 in and 3/32 in rod?

Diameter, and the metal each suits. A 1/8 in rod suits heavier joints, while a 3/32 in rod suits thin metal and sheet work. The 3/32 vs 1/8 welding rod guide compares the sizes in full.

Can E6013 weld sheet metal?

Yes. The YESWELDER E6013 3/32 in rutile rod names light gauge metal, sheet metal and duct work as its uses, and the ATLASWELDER E6013 1/8 in rod names sheet metal among its uses too. Keep the arc short and the metal clean, and chip slag before the next pass. The best 6013 welding rod for thin metal guide has more picks for thin work.

Related: stick welding set up, best all around stick welding rod, flux core vs stick for outdoor use, and the best 7018 welding rod for beginners guide.

More buying guides