Vertical Stick Welding Tips for Beginners
Vertical stick welding comes down to an all-position rod, a holder that keeps its grip, and habits that keep the bead from sagging.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
SSIMDER Electrode Holder Set with Cable & Ground9.5/10View on Amazon - 2
Original Stinger V STV002 Insulated Welding9.5/10View on Amazon - 3
ATLASWELDER 6013 Welding Rod 3/32" 5LB9.5/10View on Amazon - 4
ARCCAPTAIN 300AMP Welding Electrode Holder9.4/10View on Amazon
A vertical joint puts gravity against the weld: the puddle wants to sag, the slag wants to run, and the rod wants to stick. The vertical stick welding tips below come down to a rod that runs in all positions, a holder that keeps its grip, and a steady hand on the puddle. This guide covers the rod choice, the holder choice and the habits that keep a vertical bead in place.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

SSIMDER Electrode Holder Set with Cable & Ground
A 300A electrode holder set with a 6.5 ft cable, ground clamp and Dinse 10-25 and 35-50 plugs, rated for home garage, farm and light commercial stick welding.
Pros
- 300A holder with a solid copper jaw and spring-loaded grip
- 6.5 ft cable with Dinse 10-25 and 35-50 plugs
- Ground clamp included, with hex screw cable connections
- 2 year warranty stated
Cons
- DC set for steel and stainless steel only, it does not weld aluminum
- No electrode size range is stated
- 6.5 ft of cable limits reach from the welder
- Cable and clamp add bulk beside a bare holder

Original Stinger V STV002 Insulated Welding
A fully insulated 350 amp electrode holder with a V grip, 95% copper and brass construction, that holds electrodes up to 3/16 inch.
Pros
- 350 amp rating with 1/0 cable capacity
- V grip holds the rod and stops it popping out
- 95% copper for better conductivity
- Fully insulated with thick brass that stays cooler longer
Cons
- No cable or ground clamp is stated with it
- No warranty term is stated
- 3/16 inch electrode capacity, so larger rods need a different holder
- No plug type is stated, so check the fit with the welder

ATLASWELDER 6013 Welding Rod 3/32" 5LB
An E6013 carbon steel stick electrode in 3/32 inch, 14 inch long, rated for all positions with a smooth arc and fast slag removal.
Pros
- All-position rod for flat, horizontal, vertical and overhead work
- Smooth arc with minimal spatter and fast slag removal
- Comes in 3/32 inch and 1/8 inch, in 5 lb and 10 lb packs
- Suits automotive repairs, gates, railings and sheet metal
Cons
- No warranty term is stated
- E6013 only, so other rod types need a separate pack
- 5 lb pack suits small jobs, and larger work needs more packs
- No holder or cable is stated with it

ARCCAPTAIN 300AMP Welding Electrode Holder
A 300 amp electrode holder with a copper alloy jaw and insulated ergonomic handle, for sticks up to 7/32 inch.
Pros
- 300 amp stinger with a copper alloy jaw
- Takes sticks up to 7/32 inch
- Insulated handle, lightweight and ergonomic
- Allen wrench and cable gasket included
Cons
- No cable is stated with it
- No ground clamp is stated with it
- No plug type is stated, so check the fit with the welder
- Rated 300 amp, so machines above that need a different holder
Vertical stick welding tips
Start with the rod. An all-position rating covers vertical work, and the E6013 rod below is listed for flat, horizontal, vertical and overhead work. The ATLAS listing offers the rod in 3/32 inch and 1/8 inch, so the diameter can match the joint: a thinner rod for thinner stock, a thicker rod for heavier stock.
Keep the arc short and watch the puddle, not the arc. A long arc sprays spatter and lets the puddle sag, while a short arc keeps the metal where the joint needs it. Move in small steps and let each step freeze before moving on, so the bead stacks instead of running down the joint.
Clean the slag between passes. The E6013 rod below is listed for easy slag removal, and slag left on the bead shows up as inclusions in the next pass. Chip it, brush it, and check the joint before striking the next arc.
Strike an arc only with the work clamped, ventilation in place and flammables cleared from the area. Wear safety glasses under the helmet when chipping slag, and keep the head out of the plume.
Pick the rod for the joint
Rod choice shapes the bead. The ATLAS E6013 rod is a carbon steel electrode for all-position work, listed for flat, horizontal, vertical and overhead positions, with a smooth arc and fast slag removal. It comes in 3/32 inch and 1/8 inch diameters, 14 inch long, in 5 lb and 10 lb packs.
E6013 suits sheet metal, gates, railings, automotive repairs and home fabrication, per the listing. It is a carbon steel rod, so match it to carbon steel work and check the machine’s door chart or manual for settings before striking an arc.
Pick a holder that holds the rod
The holder is the other part of the setup. A holder run above its rated current overheats, and a jaw that slips wastes rods and ruins welds, so match the holder’s rating to the current the work needs and the rod size to the jaw.
The holders below are rated 300A and 350 amp, with copper or brass jaws and insulated handles. The SSIMDER set adds a 6.5 ft cable, a ground clamp and Dinse 10-25 and 35-50 plugs, so it plugs into smaller and larger welders without adapters. The Stinger V holds electrodes up to 3/16 inch with a V grip that keeps the rod from popping out, and the ARCCAPTAIN holder (on Amazon) takes sticks up to 7/32 inch with a copper alloy jaw.
The gear side by side
| SSIMDER Holder Set | Stinger V STV002 | ATLAS E6013 Rod | ARCCAPTAIN 300A | |
|---|---|---|---|---|
| Type | Electrode holder set with cable and ground clamp | Electrode holder | E6013 stick electrodes | Electrode holder |
| Rating | 300A | 350 amp | All position | 300 amp |
| Rod size or cable | 6.5 ft cable, 9 mm diameter | 1/0 cable capacity | 3/32 inch rod, 14 inch long | Stick sizes up to 7/32 inch |
| Fit | Dinse 10-25 and 35-50 welders | 3/16 inch electrodes | 3/32 inch or 1/8 inch rods | Sticks up to 7/32 inch |
| Warranty | 2 years | Not stated | Not stated | Not stated |
Ratings are the maker’s figures; always follow the rod label and the machine’s manual for polarity and settings.
Gear for vertical stick welding
The rod sets the bead and the holder sets the arc, so the gear below covers the rod for the joint and the holders that grip it.
These are scored on the Gear Score: performance 30, build 20, value 20, safety 15 and warranty 15. None states a safety certification, so all score 0 for safety. The SSIMDER set states a 2 year warranty, so it carries the only warranty score here. See how we pick for the weights.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| SSIMDER Holder Set | 9.5 | 30 | 21 | 21 | 0 | 2 |
| Stinger V STV002 | 9.5 | 30 | 21 | 20 | 0 | 0 |
| ATLAS E6013 Rod | 9.5 | 29 | 20 | 21 | 0 | 0 |
| ARCCAPTAIN 300A | 9.4 | 28 | 20 | 20 | 0 | 0 |
Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score.
For more options, see our welders guides.
FAQ for welders
What rod should I use for vertical stick welding?
The rod below is an E6013 in 3/32 inch and 1/8 inch, listed for all positions including vertical, with a smooth arc and fast slag removal. Match the diameter to the joint and check the machine’s door chart or manual for settings.
Can I weld vertical with E6013?
Yes. The ATLAS E6013 listing states all-position welding in flat, horizontal, vertical and overhead positions with arc control. Keep the arc short and let each step freeze before moving on.
What amp rating should an electrode holder have?
Match the holder’s rating to the current the work needs. The holders below are rated 300A and 350 amp, and the SSIMDER set is rated 300A for home garage, farm and light commercial stick welding. A holder run above its rated current overheats, so check the rating before buying.
Does the SSIMDER set fit my welder?
The set includes Dinse 10-25 and 35-50 plugs, and the listing states the 10-25 connector works with smaller machines while the 35-50 connector handles larger welders. Check the welder’s Dinse size before ordering, since the set is the only pick here that states its plug sizes.
What size rod does the Stinger V hold?
The Stinger V holds electrodes up to 3/16 inch, with a V grip that keeps the rod from popping out of its groove. It is rated 350 amp with 1/0 cable capacity.
Can I use the SSIMDER set on aluminum?
No. The listing states it is a DC stick welding set designed for steel and stainless steel projects, and that it does not weld aluminum.
Related: stick welding for beginners, best welder for beginners, best welding electrode holder for farm use and stick welding set up.




