Best Safety Glasses (2026)
Four safety glasses for the shop, compared on ANSI listing, anti-fog and scratch coatings, UV protection, side shields and pack size.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallMAGID Y509.7/10View on Amazon - 2
Best 3 PackTICONN 3PK9.6/10View on Amazon - 3
Best Retro FitMCR SR210 Swagger9.5/10View on Amazon - 4
Best Bulk PackAstrivixDD 30 Pack9.4/10View on Amazon
A grinder throws chips, a wire wheel sheds bristles, and a MIG arc spits spatter, all at face height. Eye protection is low-cost insurance on the bench, and the best safety glasses for shop work balance a stated impact rating, lenses that stay clear, and a fit you will keep on. This roundup scores four pairs on what each listing states: certification, coatings, UV protection, side shields and pack size.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall MAGID Y50: ANSI Z87.1+ and CSA Z94.3 listing, anti-fog lenses, side shields, 99.9% UV protection and a wiper case in the box. Check price on Amazon
- Best 3 Pack TICONN 3PK: ANSI Z87.1 listing, UV400 lenses and scratch-resistant coating, three pairs for the shop or the crew. Check price on Amazon
- Best Retro Fit MCR SR210 Swagger: ANSI/ISEA Z87.1 2020 listing with the side shields on, Duramass coating and 99.9% UV filtering, in a retro frame. Check price on Amazon
- Best Bulk Pack AstrivixDD 30 Pack: 30 pairs with wrap-around lenses and anti-slip silicone tips, about 23 grams each, for a crew or a classroom. Check price on Amazon
The machines

MAGID Y50 Safety Glasses for Construction
A single pair with ANSI Z87.1+ and CSA Z94.3 listing, anti-fog and scratch-resistant lenses, side shields and 99.9% UV protection.
Pros
- ANSI Z87.1+ and CSA Z94.3 listed
- Anti-fog and scratch-resistant lenses
- Side shields and 99.9% UV protection
- Wiper case with microfiber interior included
Cons
- Single pair, no bulk pack option stated
- No warranty term stated
- Weight given only as ounces, no figure stated
- Only a black frame is listed

TICONN 3PK Clear Safety Glasses for Men & Women
Three pairs of clear polycarbonate glasses with an ANSI Z87.1 listing, UV400 protection and scratch-resistant lenses.
Pros
- ANSI Z87.1 listed
- UV400 protection
- Scratch-resistant lenses
- 3 pack for the shop or a crew
Cons
- No anti-fog coating stated
- No side shields stated
- No warranty term stated
- One-size fit only, no sizes stated

MCR Safety SR210 Swagger (Sr2) Glasses
A retro-style pair with a Duramass scratch-resistant coating, 99.9% UV filtering and detachable side shields.
Pros
- ANSI/ISEA Z87.1 2020 listed with shields on
- Duramass scratch-resistant coating
- 99.9% UV filtering
- Detachable side shields
Cons
- No ANSI pass with side shields removed
- No anti-fog coating stated
- No warranty term stated
- Lens dimensions not stated

30 Pack Clear Safety Glasses for Men Women,Scratch
30 pairs of wrap-around glasses with anti-slip silicone temple tips, about 23 grams each, for a crew or a classroom.
Pros
- 30 pairs in one pack
- Wrap-around lenses with brow and side protection
- Anti-slip silicone tips on the temples
- About 23 grams each, light on the nose
Cons
- No safety certification stated
- No UV figure stated
- No warranty stated, warranty field reads NO
Other welders and gear to compare
Salfboy Clear Safety Glasses Bulk Ansi Z87.1 Scratch ImpactCheck price on Amazon
MAGID Gemstone Y50 Performance Anti-Fog Safety Glasses withCheck price on Amazon
Honeywell Uvex Ultra-Spec 2001 OTGCheck price on Amazon
KLEENGUARDTM V30 NemesisTM Safety Glasses 25688 with MirrorCheck price on Amazon
Pyramex Safety Shade 3.0 Safety GlassesCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Lens | Certification | Pack | Warranty |
|---|---|---|---|---|---|
| MAGID Y50 | 9.7/10 | Clear polycarbonate | ANSI Z87.1+, CSA Z94.3 | 1 pair | Not stated |
| TICONN 3PK | 9.6/10 | Clear polycarbonate | ANSI Z87.1 | 3 pack | Not stated |
| MCR SR210 Swagger | 9.5/10 | Clear polycarbonate | ANSI/ISEA Z87.1 2020 | 1 pair | Not stated |
| AstrivixDD 30 Pack | 9.4/10 | Clear polycarbonate | Not stated | 30 pack | Not stated |
All specs here repeat what the maker rates and the listing prints, copied down 3 November 2026.
Buying guide: the best safety glasses
Certification
ANSI Z87.1 is the impact standard the listings here cite. MAGID lists ANSI Z87.1+ for high impact plus CSA Z94.3, the strongest set here. TICONN lists ANSI Z87.1, and MCR lists ANSI/ISEA Z87.1 2020 with the side shields fitted. AstrivixDD states no certification, so its lenses carry no rated impact claim. Check the marking on the lens or frame when the pair arrives, and match the rating to the work: grinding and chipping call for a rated pair, not an unrated one.
Lens coatings
Anti-fog coating matters when you move between cold air and a warm shop, or wear a mask under a hood. Only MAGID lists anti-fog lenses here. Scratch-resistant coatings keep vision clear over time, and TICONN, MAGID and MCR all list one. AstrivixDD lists scratch and impact resistance for its lenses, with no coating name stated.
Side protection
Chips do not always come straight at you. MAGID has permanent side shields, MCR has detachable ones, and AstrivixDD uses wrap-around lenses with brow and side protection. TICONN lists no side shields. MCR warns that with the shields removed the frame does not pass ANSI/ISEA Z87.1 2020, so keep them fitted.
Fit and weight
A pair that pinches gets left on the bench. TICONN lists a one-size fit for most adult face shapes, and AstrivixDD lists a fit for most adults and teenagers, with anti-slip silicone tips and a weight of about 23 grams per pair. MAGID lists a flexible black nylon frame with soft gray temple pads and a weight of just ounces, with no figure stated. Try the fit with your hood or respirator on, since temple arms can clash with straps.
Pack size
One pair suits one welder. TICONN sells a 3 pack for the shop or a small crew, and AstrivixDD sells a 30 pack for a classroom or a large crew. A bulk pack is only a bargain if the pairs get worn, so check the fit on one pair before handing out the rest.
Use as directed. Safety glasses guard against flying particles, not against arc flash, so wear a welding helmet with the right shade over them when you strike an arc. Keep lenses clean and replace any pair with a scratched or cracked lens. See the OSHA welding overview and our Safety Disclaimer.
Before You Strike an Arc
- Check the side shields are fitted before you start, since the MCR frame only passes ANSI/ISEA Z87.1 2020 with them on.
- Check the lens marking for the ANSI rating and match it to the job: grinding and chipping call for a rated pair.
- Check the fit with your helmet on, since temple arms can clash with hood straps.
- Keep the wiper case from the MAGID pair in the shop so the lenses stay clean.
- Check each pair on arrival against the listing: count the pack, look for the rating mark, and check the shields.
FAQ for welders
Why wear safety glasses?
Grinding, chipping, cutting and wire brushing throw particles at face height, and a chip in the eye ends the day fast. Safety glasses with a stated impact rating put a rated barrier between the work and your eyes. They do not replace a welding helmet when you strike an arc, since they guard against particles, not arc flash.
How do I choose safety glasses for welding?
Start with the rating: look for an ANSI Z87.1 listing, or Z87.1+ for high impact. Then check the coatings, anti-fog for humid shops and scratch-resistant for daily wear, and side shields for peripheral protection. Then check the fit with your helmet on, and the pack size against how many pairs your shop needs.
How do I clean plastic safety glasses?
Rinse dust off under running water before wiping, so grit does not scratch the lens. Use a microfiber cloth, like the one in the MAGID wiper case, and mild soap if needed. Never wipe a dry, dusty lens with a shop rag, and replace a pair when the lens is scratched or cracked.
Do safety glasses need side shields?
Side shields guard against particles coming from the side, which a flat lens misses. MAGID lists permanent side shields and MCR lists detachable ones, while AstrivixDD uses wrap-around lenses for side coverage. If your pair has detachable shields, keep them fitted, since the MCR frame only passes its stated rating with them on.
What does ANSI Z87.1 mean?
ANSI Z87.1 is the US standard for eye protection against impact, and a listing that cites it claims the glasses meet its impact requirements. Z87.1+ marks the high-impact version of the standard. Three pairs here cite a Z87.1 listing, and AstrivixDD states none.
Related: welding safety gear, welding helmet vs safety glasses, best safety glasses with side shields, best safety glasses for grinding, best safety glasses to wear over glasses, welding goggles vs safety glasses, best safety glasses for welding, welding safety gear checklist for beginners, best welding helmet for beginners, and the welding helmets hub.
Scoring, line by line
Each pair is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. No warranty term is stated for any pair here, so every pair scores zero on that criterion; the ranking comes from the other four.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| MAGID Y50 | 9.7 | 32 | 22 | 20 | 8 | 0 |
| TICONN 3PK | 9.6 | 29 | 21 | 21 | 7 | 0 |
| MCR SR210 Swagger | 9.5 | 28 | 21 | 19 | 7 | 0 |
| AstrivixDD 30 Pack | 9.4 | 27 | 20 | 21 | 0 | 0 |
A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number.
MAGID leads on the strongest certification set and the only anti-fog lenses here. TICONN is the value pick with three certified pairs, while MCR suits a welder who wants a retro frame with a stated rating. AstrivixDD is the bulk buy for a crew, with no stated rating.




