Hobart Handler 140 vs 190: Which One Should You Buy?
Replacement MIG guns for Hobart Handler 140-family and 190-family welders compared on fitment, cable length and consumables.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
ZINGER MIG Welding Gun Torch fits 245924 Hobart9.5/10View on Amazon - 2
ZINGER MIG Welding Gun Torch fit 245926 Hobart9.5/10View on Amazon - 3
ZINGER MIG Welding Gun Torch fits 245924 Hobart9.5/10View on Amazon - 4
ZINGER MIG Welding Gun Torch fit 245926 Hobart9.5/10View on Amazon
Verdict. Pick the 245924 gun if you run a Handler 140-family welder, and the 245926 gun if you run a Handler 190-family welder. Within each side, the only choice is 10 ft or 15 ft of cable.
When the gun itself is worn and starts sputtering, feeding rough or arcing where it should not, a direct replacement gun gets the welder back to work without replacing the machine. This hobart handler 140 vs 190 comparison covers replacement MIG guns for the Handler families, not the welders themselves. The listings below show guns for each family, and the real choice is fitment, then cable length.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
The four guns

ZINGER MIG Welding Gun Torch fits 245924 Hobart
A 15 ft, 100 Amp replacement MIG gun for Hobart Handler 140-family welders, fitting part 245924 with standard .030 and .035 inch tips.
Pros
- Fits Handler 140-family welders
- 15 ft cable for reach around the shop
- 100 Amp rating stated
- Standard .030 and .035 inch tips stated
Cons
- No warranty term is stated
- No duty cycle stated
- No weight stated
- 15 ft of cable to coil and store

ZINGER MIG Welding Gun Torch fit 245926 Hobart
A 15 ft, 100 Amp replacement MIG gun for Hobart Handler 190-family welders, fitting part 245926 with standard .030 and .035 inch tips.
Pros
- Fits Handler 190-family welders
- 15 ft cable for reach around the shop
- 100 Amp rating stated
- Standard .030 and .035 inch tips stated
Cons
- No warranty term is stated
- No duty cycle stated
- No weight stated
- 15 ft of cable to coil and store

ZINGER MIG Welding Gun Torch fits 245924 Hobart
A 10 ft, 100 Amp replacement MIG gun for Hobart Handler 140-family welders, fitting part 245924 with standard .030 and .035 inch tips.
Pros
- Fits Handler 140-family welders
- Direct replacement for part 245924
- 100 Amp rating stated
- Standard .030 and .035 inch tips stated
Cons
- No warranty term is stated
- No duty cycle stated
- No weight stated
- 10 ft cable gives less reach than the 15 ft version

ZINGER MIG Welding Gun Torch fit 245926 Hobart
A 10 ft, 100 Amp replacement MIG gun for Hobart Handler 190-family welders, fitting part 245926 with standard .030 and .035 inch tips.
Pros
- Fits Handler 190-family welders
- Direct replacement for part 245926
- 100 Amp rating stated
- Standard .030 and .035 inch tips stated
Cons
- No warranty term is stated
- No duty cycle stated
- No weight stated
- 10 ft cable gives less reach than the 15 ft version
Other welders and gear to compare
Hobart 500578 Multi-Handler 200Check price on Amazon
Hobart Drive Roll for Handler 125EZ/125 & Auto Arc 130Check price on Amazon
Side by side
| Factor | 140-side guns | 190-side guns | Takeaway |
|---|---|---|---|
| Fitment | Handler 135, 140, 175, 180, 187, AutoArc XLT142, XLT182 | Handler 190, 210, 210MVP | Fitment is the real difference |
| Part number | 245924 (H-10, 195957, H100S2-10) | 245926 (H100S4-10) | Match the part number to your welder |
| Cable length | 10 ft and 15 ft | 10 ft and 15 ft | Same choice on both sides |
| Amps | 100 Amp | 100 Amp | Tie: both state 100 Amp |
| Tips | .030 and .035 inch | .030 and .035 inch | Tie: same consumables |
| Nozzle and diffuser | 169-715 nozzle, 169-716 diffuser | 169-715 nozzle, 169-716 diffuser | Tie: same numbers |
| Cable | Pure copper cable stated | Pure copper cable stated | Tie: same claim |
| Warranty | Not stated | Not stated | Tie: neither states a term |
Ratings in this table are the makers’ own claims taken from each product page (30 October 2026). No listing states a CSA, UL or ETL listing, a duty cycle, a weight or a warranty term.
Hobart handler 140 vs 190: fitment first
Fitment is the whole comparison. The 140-side guns replace part 245924 (H-10, H100S2-10) and fit Handler 140-family welders. The 190-side guns replace part 245926 (H100S4-10) and fit Handler 190-family welders. No listing states that a gun fits the other family’s part number, so match the part number to your welder rather than assuming the guns interchange. Check the part number on your old gun before ordering.
Cable length: 10 ft or 15 ft
Each side offers the same gun in 10 ft and 15 ft. The 15 ft guns give more reach around the bench and the shop floor, while the 10 ft guns keep a shorter cable to coil and manage. Length is the only difference within a side: the amps, tips, nozzle, diffuser, cable material and handle are stated the same on both lengths. Pick the length that suits how far you stand from the welder, not the side.
Consumables: one standard set
All four listings use the same standard consumables: the same standard tip sizes, a 169-715 gas nozzle and a 169-716 gas diffuser. That shared set is good news for a shop that runs both families, since tips, nozzles and diffusers carry over even though the guns themselves do not. The 140-side 15 ft listing also mentions a tip kit in its title. Confirm the tip size your wire needs before ordering, since the listings state the sizes without saying which ships in the box.
Build: copper cable and handle
All four listings state the same build: a pure copper cable the maker says improves conductivity and durability, and an ergonomic handle design the maker says saves effort. No listing states a weight, a duty cycle or a safety listing, so build cannot be ranked beyond those two stated points. The four guns read as the same gun in different fitments and lengths, which matches how close their listings run.
What is the same
It is worth stating plainly: the two sides tie on every spec except fitment. Both sides state 100 Amp, the same tip sizes, the same nozzle and diffuser numbers, the same pure copper cable claim and the same ergonomic handle claim. Neither side states a warranty term, a duty cycle or a weight. Neither side leads on specs, because the listings give no spec that puts one side ahead of the other.
Choose the 140-side gun if
- You run a Handler 140-family welder.
- Your old gun carries part number 245924.
- You want the 15 ft cable for reach, or the 10 ft cable for a shorter coil.
Choose the 190-side gun if
- You run a Handler 190-family welder.
- Your old gun carries part number 245926.
- You want the 15 ft cable for reach, or the 10 ft cable for a shorter coil.
Before You Strike an Arc
- Check the part number on your old gun: 245924 fits the 140 family, 245926 fits the 190 family.
- Confirm your Handler model is on the listing’s fit list before ordering.
- Match the tip size to your wire: the listings state the standard tip sizes.
- Check the nozzle and diffuser numbers: 169-715 nozzle and 169-716 diffuser on all four listings.
- Pick the cable length for your workspace: 10 ft for close work, 15 ft for reach.
FAQ for welders
Can I use a 140 gun on a Handler 190?
Not according to the listings. The 140-side guns replace part 245924 and the 190-side guns replace part 245926, and neither listing states fitment for the other family’s part number. Match the part number, not just the brand.
What is the difference between the 10 ft and 15 ft guns?
Cable length only. Both lengths on a side state the same 100 Amp rating, the same tip sizes, the same nozzle and diffuser numbers, and the same cable and handle claims.
Do these guns use standard consumables?
Yes. All four listings state the same standard tip sizes, a 169-715 gas nozzle and a 169-716 gas diffuser.
Are these the Handler 140 and 190 welders?
No. These listings are replacement MIG guns for those welder families, not the welders themselves. The 140-side guns fit Handler 140-family welders, and the 190-side guns fit Handler 190-family welders.
Do any of these guns list a warranty?
No. None of the four listings states a warranty term, so there is no coverage to compare.
Related: MIG wire sizes compared, best contact tips for MIG welder, air cooled vs water cooled MIG gun and MIG welders hub.
Scoring, line by line
Each gun is scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. No listing states a safety listing or a warranty term, so every gun scores zero on those two factors and the ranking rests on cable length, through the value score.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Zinger 140 15ft Gun | 9.5 | 29 | 21 | 21 | 0 | 0 |
| Zinger 190 15ft Gun | 9.5 | 29 | 21 | 21 | 0 | 0 |
| Zinger 140 10ft Gun | 9.5 | 29 | 21 | 20 | 0 | 0 |
| Zinger 190 10ft Gun | 9.5 | 29 | 21 | 20 | 0 | 0 |
The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure.




