Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Brazing Torch Setup: Gear, Gas and First Steps

A brazing torch setup joins a torch head, hose and gas cylinder, with a regulator fitted on kits that use one, and the three kits in this guide show how those parts fit together for copper pipe and HVAC work.

Brazing Torch Setup: Gear, Gas and First Steps
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Flame King Propane Gas Torch 6,000 BTU Kit w/ 3Flame King Propane Gas Torch 6,000 BTU Kit w/ 39.5/10View on Amazon
  2. 2TURBOTORCH 0386-0832 PL-5ADLX-MC Self-LightingTURBOTORCH 0386-0832 PL-5ADLX-MC Self-Lighting9.5/10View on Amazon
  3. 3TAUSOM MAPP Gas Torch Kit 25000 BTUTAUSOM MAPP Gas Torch Kit 25000 BTU9.5/10View on Amazon

A copper joint that will not take solder, or an HVAC line that needs a silver braze, is the job that sends most people to a torch. A brazing torch setup is the torch head, hose and gas cylinder joined in the right order, with the tip and gas matched to the metal in front of you. A kit that uses a regulator fits it between the cylinder and the hose. This guide walks through that order, then shows three kits and what each brings to the bench.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Flame King Propane Gas Torch 6,000 BTU Kit w/ 3

Flame King Propane Gas Torch 6,000 BTU Kit w/ 3

Flame King9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A propane kit with three interchangeable burners, a 47-inch hose and a 90 day manufacturer warranty, the only stated warranty term in this guide.

Pros

  • Three interchangeable burners, including a 7/8-inch brazing tool for copper pipes
  • 47-inch hose gives room to move the torch while the cylinder stays put
  • 90 day manufacturer warranty, the only stated term here
  • Arrives fully assembled and works with a standard 1-lb refillable propane cylinder

Cons

  • 6,000 BTU output is the lowest stated output of the three kits
  • Propane cylinder sold separately
  • No regulator is stated in the box
  • At 60.0 inches long in the package, it needs more shelf space than the other kits
TURBOTORCH 0386-0832 PL-5ADLX-MC Self-Lighting

TURBOTORCH 0386-0832 PL-5ADLX-MC Self-Lighting

ESAB9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An air acetylene kit with a regulator, handle, hose and tip, rated by the maker for soft solder to 4 inch and silver braze to 2 inch.

Pros

  • Includes AR-MC regulator, G-4 handle, AH-12 hose and PL-5A tip in the box
  • Maker rates it for soft solder to 4 inch and silver braze to 2 inch
  • Quick-disconnect handles and tips with replaceable tips
  • Color coded O rings for quick gas identification, plus gauge guards and cylinder wrench

Cons

  • No warranty term is stated
  • No heat output figure is stated in the listing
  • Acetylene cylinder not included in the kit
  • 12.0 x 5.0 x 12.0 inch size is the bulkiest of the three kits
TAUSOM MAPP Gas Torch Kit 25000 BTU

TAUSOM MAPP Gas Torch Kit 25000 BTU

TAUSOM9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A MAPP gas kit with a self-ignition piezo trigger, a 4.9 ft reinforced hose and a solid brass torch head, rated at 25,000 BTU.

Pros

  • 25,000 BTU output, the highest stated output of the three kits
  • Built-in piezo igniter for instant lighting
  • 4.9 ft reinforced hose keeps the tank away from the heat
  • Solid brass torch head with a 6-blade design and CGA600 fitting

Cons

  • No warranty term is stated
  • No tip sizes are stated in the listing
  • MAPP gas cylinder not included
  • Hose length is fixed at 4.9 ft, with no longer option stated

Brazing torch setup in order

  1. Check the parts. Look over the cylinder valve, the hose and the torch head, and the regulator if the kit has one, for damage before connecting anything. A cracked hose or a bent fitting is a reason to stop and replace the part.
  2. Connect regulator, hose and head. Fit the regulator to the cylinder where the kit has one, then the hose to the regulator or to the cylinder, and the torch head to the hose. Snug each fitting with a wrench and leave the torch valve closed while you work.
  3. Open the gas slowly. Open the cylinder valve slowly where the kit has a separate one, then open the torch valve a little and light the torch with its igniter where the kit has one, or with a separate spark lighter. Never light a torch with the valve wide open.
  4. Set the flame and check for leaks. Adjust the flame with the torch valve or the flame control knob until it holds steady. Brush soapy water over each joint and watch for bubbles before you start heating the work.
  5. Shut down in order. When the work is done, close the torch valve, then the cylinder valve where the kit has a separate one, and let the torch cool before putting it away.

What gas and tip the job needs

The three kits cover the three common gases. The TAUSOM kit (on Amazon) runs MAPP gas at a stated 25,000 BTU, the highest output here, and the maker lists it for HVAC, metalwork and pipe soldering. The Flame King kit (on Amazon) runs propane at a stated 6,000 BTU with three burners, which suits soldering, thawing and small repairs. The ESAB kit runs air acetylene and states soft solder to 4 inch and silver braze to 2 inch, which suits copper pipe and HVAC joints that need a silver braze.

Match the tip to the pipe: the Flame King kit carries a 7/8-inch brazing tool for copper pipes, a 3/4-inch nozzle and a 1-1/2-inch flat burner. A small tip on a large joint wastes gas and time, and a large tip on a small joint overheats the metal around it. For filler metal, see our best brazing rod for HVAC copper and the brazing rod types guide. The gas choice itself is compared in our MAPP gas vs propane brazing torch guide.

Compare the torches

Torch Fuel and gas Heat output Hose Warranty
Flame King Propane Torch Kit Propane 6,000 BTU 47-inch 90 day manufacturer warranty
ESAB TURBOTORCH PL-5ADLX-MC Air acetylene Not stated AH-12 hose Manufacturer Warranty, no term stated
TAUSOM MAPP Torch Kit MAPP gas 25,000 BTU 4.9 ft reinforced Not stated

The Flame King kit carries the only stated warranty term here, at 90 days, and the only three-burner set. The ESAB kit is the only kit here with a regulator in the box. The TAUSOM kit has the highest stated output at 25,000 BTU and a self-ignition piezo trigger. Pick the kit whose gas and parts match the joints you braze most.

The gear for a brazing torch setup

Each kit below handles a different part of the setup: the Flame King kit covers small propane work with three burners, the ESAB kit covers air acetylene brazing with a regulator in the box, and the TAUSOM kit covers high-output MAPP work on HVAC and copper pipe.

Gas, flame and fume safety. Brazing makes fumes, and galvanized metal gives off fumes that are harmful to breathe. Work with ventilation or outdoors with your head out of the plume, keep cylinders upright and chain full-size cylinders, and clear dry grass and anything flammable from the area. Check the manual for each kit before lighting it. See the OSHA welding overview.

FAQ for welders

What gas do I need for brazing copper pipe?

MAPP gas, propane and air acetylene all work on copper pipe, and the kits in this guide cover all three. MAPP gas suits HVAC work where the joint needs heat fast, propane suits small soldering and repair jobs, and air acetylene suits silver brazing. Match the gas to the filler rod the joint calls for, and check the rod guide linked above.

Can I braze with a propane torch?

Yes, for small copper joints and light brazing work. The Flame King kit is built for that kind of job, with three burners and a stated 6,000 BTU output. For larger joints or silver brazing, the air acetylene ESAB kit states soft solder to 4 inch and silver braze to 2 inch.

Do I need a regulator for a brazing torch?

It depends on the gas. The ESAB air acetylene kit includes an AR-MC regulator in the box, with gauge guards and a cylinder wrench. The TAUSOM MAPP kit and the Flame King propane kit state no regulator in the box, so check what the cylinder connection needs before ordering.

How do I light a brazing torch?

Open the cylinder valve slowly where the kit has a separate one, open the torch valve a little, and light the gas with the torch igniter where the kit has one. The TAUSOM kit has a built-in piezo igniter, and the ESAB kit is self-lighting; the Flame King kit states no igniter, so light it with a separate spark lighter. Never light a torch with the valve wide open, and never light it near flammable material.

What tip size do I need for copper pipe?

Match the tip to the pipe and the joint. The Flame King kit includes a 7/8-inch brazing tool for copper pipes, a 3/4-inch nozzle and a 1-1/2-inch flat burner, so the tip can match the joint. The TAUSOM listing states no tip sizes, and the ESAB listing names a PL-5A tip without a size in inches.

Can a brazing torch cut metal?

The TAUSOM listing mentions cutting among its uses, but a brazing torch is a heating tool first. For cutting, a cutting torch with the right tip and gas mix is the proper tool. See our oxy acetylene torch setup guide for the cutting side of the bench.

Related: soldering torch vs brazing torch, welding torch types, how hot is a welding torch, and the welders hub.

More buying guides