Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Tapping Drill Chart: How to Read It and Pick the Right Drill

A tapping drill chart matches each tap size to the drill size that leaves the right amount of thread, so you drill once and tap clean threads.

Tapping Drill Chart: How to Read It and Pick the Right Drill
On this page

You need a threaded hole in a steel bracket, and the tap has to cut clean threads the bolt will actually take. Drill the hole too small and the tap binds and snaps. Drill it too big and the threads come out shallow and the bolt strips. A tapping drill chart takes the guesswork out of that choice: find your tap size in the chart, read across to the drill size it lists, and drill that hole before you tap.

As an Amazon Associate I earn from qualifying purchases. This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

What a tapping drill chart is

A tapping drill chart is a table that pairs a tap size with the drill size that leaves the right amount of metal for the thread. The tap size runs down the left side, and the drill size sits beside it in the next column. Some charts add a column for thread depth, shown as a share of a full thread, and a column that marks the tap as coarse or fine. The chart does the matching for you: you look up the tap in your hand and read off the drill that fits it. Keep the chart near the drill press or taped inside the lid of the tap case, where you can reach it before you drill.

How to use a tapping drill chart

Start with the tap itself, not the chart. Read the size and pitch stamped on the tap shank, and check whether it is coarse or fine. Find that tap size in the left column of the chart. Read across the row to the drill size column and note the drill it names. If the chart shows several drill sizes for that tap, read the thread depth column and pick the row that matches the thread depth you want. Drill the hole with the drill size the chart gives, then tap it. When the chart and the tap disagree, trust the tap in your hand and check the chart again before you drill.

  • Read the tap. Size and pitch are stamped on the shank.
  • Find the row. Match the tap size in the left column.
  • Read across. The drill size sits in the next column.
  • Check the depth. The thread depth column tells you how much thread the hole leaves.

Chart or guesswork

With the chart Without the chart Check before you drill
Drill size Read off the chart for your tap From memory or calculation Match the drill to the tap in your hand
Thread depth The chart shows the depth column No depth to aim for Pick the row for the depth you want
Tap breakage risk Lower, the hole fits the tap Higher, a tight hole binds the tap Back the tap out to clear chips
Time in the shop A quick look, then drill Rework and broken taps Keep the chart near the drill press
Result Threads that take the bolt Threads that strip, or a tap that snaps Run a bolt in by hand to check

Checking the chart takes a moment and saves the tap, the part and the time a broken tap eats. Guesswork works until it does not, and a snapped tap in a finished part is the expensive way to learn the drill size. Keep a printed chart at the bench and use it every time you tap a hole.

When the drill size is wrong

A hole drilled too small leaves too much metal for the tap to cut. The tap works hard, the threads tear, and the tap can snap off in the hole, where it is hard to remove. A hole drilled too big leaves too little metal, so the threads come out shallow and the bolt pulls out under load or strips when you tighten it. The chart keeps you between those failures: the hole is large enough for the tap to cut freely and small enough to leave threads the bolt will take. If a bolt feels loose in the finished threads, the hole may have been too big. If the tap squeals and binds, the hole may be too small, or the tap may be dull or short of fluid.

Drilling the hole

Center punch the spot so the drill starts where you marked it, and clamp the work so it cannot spin. Use cutting fluid made for drilling and tapping, and let the drill cut at a steady feed without forcing it. A drill press holds the drill square to the work; a hand drill needs a steady hand and a square eye. Clear chips from the hole often so they do not pack and bind the drill. See the best cutting fluid for steel guide and the best drill bit set for metal picks.

Tapping the hole

Start the tap square to the hole, with tapping fluid on the tap and in the hole. Turn the tap in with a tap wrench, a little at a time, and back it off to break the chips. Never force a tap that binds; back it out, clear the chips, add fluid and try again. A tap that starts crooked cuts crooked threads, so check the square before the tap bites deep. See the best tapping fluid picks and the best tap wrench guide.

Drilling and tapping safety. Wear eye protection and clamp the work before the drill starts. Keep gloves away from rotating parts, keep guards in place, and keep hands clear of the chuck. Hot chips and sharp edges cut, so brush chips away instead of wiping them with a bare hand. Work with ventilation and keep flammable material away from the bench. OSHA machine guarding rules cover guards, clamping and keeping hands clear of moving parts. See the drill press safety tips.

For more options, see our guides guides.

FAQ for welders

What is a tapping drill chart?

It is a table that matches a tap size to the drill size that leaves the right amount of thread. You look up the tap you hold, read across to the drill size, and drill that hole before you tap. A printed chart belongs near the drill press, where you can reach it before you drill.

Do coarse and fine taps need different drill sizes?

Yes. A fine tap cuts more threads into the same length, so it needs a larger drill hole than a coarse tap of the same size. The chart lists coarse and fine taps in separate rows, so read the row that matches the tap in your hand. Mixing them up leaves threads too shallow or a tap that binds.

What happens if the drill hole is too small?

The tap has to cut too much metal, so it binds, tears the threads and can snap off in the hole. A snapped tap is hard to remove and can ruin the part. Drill the size the chart gives, and back the tap out often to clear chips.

What happens if the drill hole is too big?

The threads come out shallow, so the bolt strips or pulls out under load. The joint looks finished but holds poorly. Drill the size the chart gives, and run a bolt in by hand to check the threads before you trust the joint.

Can I tap a hole without a chart?

You can, but you have to work the drill size out from the tap size and pitch, and a wrong size costs a tap or a part. A chart is the fast way to get the size right, so keep one at the bench and use it every time you tap.

Related: large size tap and die set, best tapping fluid, best tap wrench, best cutting fluid for steel, and the drilling and tapping hub. Also see the drill press speed chart.

More buying guides

Metal Fab Tools ·

Drill Press Speed Chart by Bit Size

A drill press speed chart matches bit size and material to spindle speed, and this guide shows how to read it and which bits…