Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Large Size Tap and Die Set: Sizes Explained

A large size tap and die set runs from small #4 and M3 sizes up to 1 inch and M18, and this guide explains how SAE and metric sizes are marked and how to pick the largest size you need.

Large Size Tap and Die Set: Sizes Explained
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1uxcell Adjustable Tap Wrench Handleuxcell Adjustable Tap Wrench Handle9.6/10View on Amazon
  2. 2Starrett Tap WrenchStarrett Tap Wrench9.6/10View on Amazon
  3. 3WILLBOND 2 Pcs Tap WrenchWILLBOND 2 Pcs Tap Wrench9.6/10View on Amazon

A bolt that will not thread back into its hole stops the job cold, and the fix is a tap and die set that cuts the thread clean again. A large set covers the sizes a shop actually meets, from small machine screws up to big bolts. Large size tap and die set means a set whose largest size reaches 1 inch on the SAE side, and this guide explains how those sizes are marked and how to pick one.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Large size tap and die set: what large means

Large means the top size in the box. The KJE set runs from 1/4 inch-20 to 1 inch-14, which is the largest SAE size in the listings here. The GEARWRENCH set runs from 4-40 to 3/4 inch and 3 mm to 18 mm. The OMT 87-piece set runs from 4-40 to 5/8-18 inch and M3 to M16. A set is large when its top size covers the bolt you thread, so read the top size before ordering.

SAE and metric sizes side by side

SAE sizes Metric sizes How to read it
Size mark #4 to 1 inch M3 to M18 SAE uses fractions of an inch; metric uses millimeters
Thread spacing Threads per inch, such as 20 or 14 Pitch in millimeters, such as 1.0 or 1.75 The number after the size gives the spacing
Coarse and fine UNC coarse, UNF fine Coarse and fine pitches in the same set Coarse for general work, fine for adjustment
Pipe threads NPT, such as 1/8-27 No metric pipe thread in these sets NPT is a tapered pipe thread
Largest size in the listings 1 inch, in the KJE set M18, in the GEARWRENCH set Check the largest size before ordering
What comes with it Taps, dies, wrenches, pitch gauge Taps, dies, wrenches, pitch gauge Count the accessories, not just the taps

The table shows the two size systems side by side. SAE sizes use fractions of an inch with threads per inch, and metric sizes use millimeters with pitch in millimeters. Both systems appear in the same set on the listings here, so one box can cover both.

How to read a tap and die size

Read an SAE size as diameter first, then threads per inch: 1/4-20 is 1/4 inch diameter with 20 threads per inch, and 1/2-13 is 1/2 inch diameter with 13 threads per inch. Read a metric size as M, then diameter in millimeters, then pitch: M6x1.0 is 6 mm with a 1.0 mm pitch, and M12x1.75 is 12 mm with a 1.75 mm pitch. The pitch gauge in the set tells you the pitch when the marking is worn or missing.

Coarse and fine threads share the same diameter but differ in pitch: 1/2-13 is coarse and 1/2-20 is fine, and M10x1.5 is coarse while M10x1.0 is fine. NPT is a pipe thread, not a bolt thread: 1/8-27 NPT is the pipe size in the EFFICERE sets here. Match the thread to the bolt or the hole, not just the diameter.

What comes in a large set

A set holds taps for internal threads and dies for external threads, plus the wrenches and gauges to use them. The OMT 87-piece set holds 78 taps and dies, 5 adjustable wrenches, a 1/8 inch screwdriver, 2 thread gauges and a 5 inch center punch. The GEARWRENCH set holds 48 taps and dies, 2 ratcheting T handles, 3 sizes of tap adapters and 2 sizes of die adapter, 2 extension adapters and 5 screw extractors. The KJE set holds 20 taps, 20 dies, a tap wrench, a die wrench with adapter, a T-handle and a pitch gauge, with spiral flute extractors for stuck fasteners.

Ratcheting handles help in tight spots: the GEARWRENCH and toolant handles (on Amazon) wind with a 5 degree swing arc and have a reversing lever, so the handle turns without hand over hand work. A twist lock guide system keeps the die centered while cutting. The VEVOR set holds 51 taps and 51 dies, with a tap wrench for M3 to M12 and a tap wrench for M6 to M20.

How to use a tap and die set

The EFFICERE sets here are for hand use only: the listing says not to use them with power tools, which deliver over torque and damage the threads. Start the tap or die straight, turn it a little at a time, and back it off to clear the chips. If the tap or die jams, do not force it: reverse the direction to clear the chips and debris before continuing, or the tool can break.

Keep the set in its case between jobs, with each tap, die, wrench and gauge in its place, so the next job starts with the right size in hand. A blow-molded case holds the pieces sorted, and a tilted holder or a drawer keeps them in reach. Check the size marking on the tap or die before cutting, since a wrong size cuts a wrong thread.

FAQ for welders

What is the largest tap and die size in these sets?

1 inch on the SAE side, in the KJE set, which runs from 1/4 inch-20 to 1 inch-14. On the metric side, the GEARWRENCH set runs to 18 mm, and the OMT 87-piece set runs to M16. Check the top size on the set you pick before ordering.

What is the difference between coarse and fine threads?

Coarse and fine threads share the same diameter but differ in pitch. On the SAE side, 1/2-13 is coarse and 1/2-20 is fine. On the metric side, M10x1.5 is coarse while M10x1.0 is fine. Match the thread to the bolt or the hole, not just the diameter.

Do I need SAE or metric taps and dies?

Both, if the work mixes them. The sets here hold SAE and metric sizes in the same box, so one set covers both. Check which system the bolts on the job use before ordering.

Can I use a tap and die set with a power drill?

The EFFICERE listings here say their sets are for hand use only, and power tools deliver over torque that damages the threads. Use the tap wrench and die stock by hand, and back the tool off to clear chips as you cut.

What do I do if a tap jams?

Do not force it. Reverse the direction to clear the chips and debris before continuing, or the tool can break and the die stock or wrench can crack. Start the tap straight, turn it a little at a time, and back it off to clear chips as you cut.

Keep reading: How to Use Thread Gauge explains pitch, angle and fit, and What Size Drill Bit to Tap 8-32 covers the drill bit for an 8-32 tap. For the wrenches in these sets, Best Tap Wrench Large covers big taps. See the full Metal Fab Tools category for more guides.

More buying guides