Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How to Use Thread Gauge: Pitch, Angle and Fit

A thread gauge matches the pitch on a screw, nut or tapped hole by finding the blade that seats in the thread, then reading the size marked on the blade.

How to Use Thread Gauge: Pitch, Angle and Fit
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Professional Thread GaugeProfessional Thread Gauge9.7/10View on Amazon
  2. 2PEC Tools Screw Pitch Gauge, 51 Leaves, 4–84 TPIPEC Tools Screw Pitch Gauge, 51 Leaves, 4–84 TPI9.7/10View on Amazon
  3. 3ChgImposs Metric & Imperial & US Screw Gauge SAEChgImposs Metric & Imperial & US Screw Gauge SAE9.6/10View on Amazon
  4. 4Grip US American National Thread Pitch Gauge MMGrip US American National Thread Pitch Gauge MM9.6/10View on Amazon

A bolt that will not thread into a tapped hole stops the job until the pitch is known, and guessing the size wastes more time than measuring it. This guide shows how to use thread gauge on a screw, a nut, a fastener or in a tapped hole: fan the blades, find the blade that seats in the thread, and read the size marked on it.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Professional Thread Gauge

Professional Thread Gauge

zikyunw9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3-in-1 gauge that reads metric, Whitworth and US threads in one tool, for matching the pitch on a screw, nut or tapped hole.

Pros

  • Reads metric, Whitworth and US threads in one tool
  • Metric 0.25 to 6.0mm, imperial 4G to 62G and US 8 to 28 TPI
  • Stainless steel blades with an anti-rust finish
  • V-groove checks the lathe cutting tool angle

Cons

  • US range of 8 to 28 TPI matches the ChgImposs set and is narrower than the Grip gauge's 4 to 42 SAE range
  • 2.9 inch body is smaller than the Grip gauge's 5.7 inch body, with less to hold
  • Metric range ends at 6.0mm, so coarser pitches need another gauge
  • Metric, Whitworth and US blades share one set, so the blades for one system sit among the others
PEC Tools Screw Pitch Gauge, 51 Leaves, 4–84 TPI

PEC Tools Screw Pitch Gauge, 51 Leaves, 4–84 TPI

PEC Tools9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 51-leaf English gauge that reads 4 to 84 TPI on internal and external threads, for matching the pitch on an English fastener.

Pros

  • 51 leaves read 4 to 84 TPI, the widest English range here
  • Narrow blades check internal and external threads
  • Hardened and tempered steel blades for long-term stability
  • Every blade is stamped with its thread size

Cons

  • English threads only, so metric and Whitworth threads need another gauge
  • No warranty term is stated
  • No V-groove is stated for checking a lathe tool angle
  • 51 leaves to sort through for one size
ChgImposs Metric & Imperial & US Screw Gauge SAE

ChgImposs Metric & Imperial & US Screw Gauge SAE

ChgImposs9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A gauge that reads metric, imperial and US threads, for matching the pitch and checking the tool angle on a lathe.

Pros

  • Reads metric, imperial and US threads in one set
  • Metric 0.25 to 6.0mm, imperial 4G to 62G and US 8 to 28 TPI
  • Stainless steel blades with a wire-drawn surface
  • V-groove checks the lathe cutting tool angle

Cons

  • US range tops at 28 TPI, below the 84 TPI top of the PEC gauge
  • 55 degree and 60 degree blades share one set, so match the blade angle to the thread system before use
  • No warranty term is stated
  • No storage case is stated
Grip US American National Thread Pitch Gauge MM

Grip US American National Thread Pitch Gauge MM

GRIP GRAND RAPIDS INDUSTRIAL PRODUCTS9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A metric and SAE gauge that reads 0.25 to 5.5mm and 4 to 42 SAE, for matching the pitch on a screw, nut or tapped hole.

Pros

  • Reads metric and SAE threads in one gauge
  • Metric 0.25 to 5.5mm and SAE 4 to 42
  • 60 degree thread profiles with locking devices
  • Removes the need to measure and calculate the pitch

Cons

  • Metric and SAE only, so Whitworth threads need another gauge
  • No V-groove is stated for checking a lathe tool angle
  • 5.7 inch body is larger than the zikyunw gauge's 2.9 inch body, so it takes more room in the box
  • 0.2 lb is the heaviest stated weight here

How to use thread gauge step by step

  1. Pick the system. Metric, Whitworth or US: open the blades for the system the thread belongs to.
  2. Fan the blades. Work through them until a blade seats in the thread.
  3. Read the size. Read the size marked on the blade that seats.
  4. Lock the blade. Lock the blade in place before you set the gauge down.
  5. Check the angle. On a gauge with a V-groove, check the tool angle there when cutting threads on a lathe.

Metric, Whitworth and US threads side by side

Metric Whitworth (Imperial) US SAE English
Thread angle 60° 55° 60° Not stated
Pitch range 0.25 to 6.0mm 4G to 62G 4 to 42 SAE 4 to 84 TPI
Read by Grip, ChgImposs, zikyunw ChgImposs, zikyunw Grip, ChgImposs, zikyunw PEC

The angle separates Whitworth from the other two: metric and US threads use a 60 degree angle, and Whitworth threads use a 55 degree angle. A blade that seats in the thread gives the pitch. For the diameter behind the pitch, see micrometer vs caliper.

Which gauge fits the thread in front of you

The 3-in-1 sets cover the most ground: the ChgImposs and zikyunw gauges read metric, imperial and US threads, so a single set covers a mixed box of fasteners. The Grip gauge reads metric and SAE threads, and the PEC gauge reads English threads from 4 to 84 TPI with 51 leaves.

  • Mixed fasteners. The ChgImposs and zikyunw sets read metric, imperial and US threads, so a single set covers the box.
  • English threads only. The PEC gauge reads 4 to 84 TPI on internal and external threads, with every blade stamped with its size.
  • Metric and SAE. The Grip gauge reads 0.25 to 5.5mm and 4 to 42 SAE, with locking devices on the set.
  • Lathe tool angle. The ChgImposs and zikyunw gauges include a V-groove for checking the angle on a lathe cutting tool. Pair the gauge with a tap wrench when cutting new threads: see our best standard tap wrench picks.

The gear for this guide

The pitch is read from the blade that seats in the thread, so the gauge has to cover the system the thread belongs to: the 4 gauges below cover metric, Whitworth, US and English threads between them.

Lock the blades before storage. Each gauge here states a locking device, so lock the blades and keep the set shut between jobs.

FAQ for welders

How do I know which blade fits the thread?

Fan the blades and work through them until a blade seats in the thread. Read the size marked on the blade: the PEC gauge stamps every blade with its size, and the Grip gauge carries MM and SAE markings. A blade that does not seat is the wrong pitch or the wrong angle, so move to the next blade.

What is the difference between metric, Whitworth and US threads?

The angle differs: metric and US threads use a 60 degree angle, and Whitworth threads use a 55 degree angle. The pitch ranges differ too: metric runs 0.25 to 6.0mm, imperial runs 4G to 62G, and US runs 8 to 28 TPI on the 3-in-1 sets. The Grip gauge reads metric and SAE threads from 4 to 42 SAE.

Can a gauge check internal and external threads?

Yes, where the gauge states it: the PEC gauge states narrow blades that check both internal and external screw threads. The Grip gauge states use on a screw, nut, fastener or in a tapped hole, so it covers internal threads too.

What is the V-groove on a thread gauge for?

The V-groove checks the angle on the thread cutting tool when cutting threads on a metal lathe. The ChgImposs and zikyunw gauges state a V-groove for that check, so the gauge covers both the pitch and the tool angle.

Do I need a locking device on a thread gauge?

A locking device holds a single blade in place while you read it, and keeps the set shut for storage. All 4 gauges here state a locking device: the PEC gauge has one at each end of the case, and the zikyunw gauge (on Amazon) uses a rotary locking mechanism.

Related: how to use pipe threader, best standard tap wrench, how to use digital calipers, and the metal fab tools hub.

More buying guides