Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Thread Repair Kit: How to Fix Stripped Threads

A thread repair kit gives a stripped hole a new thread that holds the same bolt, and this guide walks through the drill, tap and insert steps in shop order.

Thread Repair Kit: How to Fix Stripped Threads
On this page

A bolt that turns without biting has stripped the threads in its hole, and the part it held is loose until that hole gets a thread again. A thread repair kit is the shop fix: a matched drill bit and tap that cut a fresh thread inside the damaged hole, plus steel inserts that restore the original thread size so the same bolt threads in and holds. This guide walks through the job in shop order, from drilling out the damage to checking the bolt fit.

As an Amazon Associate I earn from qualifying purchases. This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

What a thread repair kit does

Inside the kit, the parts work as a set. The drill bit opens the stripped hole to a clean round size. The tap cuts a new, larger thread in that hole. In a wire insert kit, the insert is a coiled steel thread that screws into the new thread and gives the original bolt a fresh surface to grip. The fitting tool winds the insert in and sets it at the right depth, and on a tang type insert a small tang snaps off after it seats. The result is a hole that takes the bolt it took before the threads stripped, without drilling a new hole in a new spot or stepping up to a larger bolt.

Side by side

Thread insert kit Oversize tap and bolt Weld and re-drill
What it fixes Stripped thread in the same hole Stripped thread, new larger bolt Cracked or worn hole
Bolt size after repair Same bolt as before Larger bolt Same bolt as before
Drilling needed Drill to the kit size, then tap Drill to the tap size, then tap Fill the hole, then drill and tap
Suits Brackets, housings and plates Holes with room for a larger bolt Holes past what an insert can grip
Skill needed Patient hand work Patient hand work Welding and machine work

An insert kit suits a stripped hole in brackets, housings and plates where the bolt size must stay the same. An oversize tap suits a hole where a larger bolt is fine. Welding and re-drilling suits a hole that is cracked or worn past what an insert can grip.

How to use a thread repair kit

Work in this order and let the tap do the cutting.

  • Clean the hole and check the thread. Brush out chips and grit, then match the bolt to a thread pitch gauge so the kit matches the thread the hole held. The thread pitch gauge chart shows the common sizes and pitches.
  • Drill out the damage. Clamp the part so it cannot move, drill straight down the center of the hole with the bit the kit calls for, and clear chips often.
  • Tap the new thread. Coat the tap with cutting fluid, start it square to the surface, and turn it in a little at a time, backing it out to break chips. Never force a tap that binds; back it out, clear the chips and try again.
  • Fit the insert. Wind the insert onto the fitting tool, thread it into the tapped hole until it sits just below the surface, then snap off the tang with the tool the kit supplies.
  • Check the bolt fit. Thread the original bolt in by hand. It should turn smoothly to full depth without wobble or drag. If it binds, back it out and look for a chip or a crossed insert.

Picking the drill bit for the job

The kit specifies the drill size for its tap. See the drilling and tapping chart to confirm it before ordering a bit. Exact size matters more than bit material: use the size the kit calls for in the parent metal, whether aluminum, cast iron or steel. The cobalt sets below are listed for hard and abrasive metals.

The Drill America 29-piece set lists bits from 1/16 inch to 1/2 inch in 1/64 inch steps, and sets in the listings run from 13 pieces to 122 pieces. The COMOWARE and ANGELSWORD 29-piece sets list M35 cobalt with 5% cobalt, and the Drill America set lists a 135-degree split point that starts without a pilot hole. Bosch lists its CO14B 14-piece set as M42 cobalt with 8% cobalt and 10x life against standard bits, and its CO21 21-piece set as cobalt with 4X longer life than standard high speed steel bits and a three-flat shank on bits 3/16 inch and larger. The MACXCOIP 13-piece set covers 1/16 inch to 1/4 inch. See HSS vs cobalt drill bit and the best drill bit for stainless steel metal roundup.

Tapping the new thread

Cutting fluid keeps the tap cool and the thread clean, and a tap wrench that grips the tap square gives a steadier turn than pliers. See the best tap wrench, best tapping fluid and best cutting fluid for steel roundups.

Fitting the insert and checking the bolt

Seat the insert just below the surface so the bolt starts cleanly, and confirm the pitch with a thread gauge if the bolt drags. See how to use thread gauge for pitch, angle and fit. A bolt that threads in by hand to full depth without wobble is a good check, not proof of strength on its own. A bolt that stops short can mean a chip, a tang left in the hole, a crossed insert or a pitch mismatch, so back it out, clean the hole and check seating and pitch. Do not re-tap a hole that already holds an insert.

Stay safe while you drill and tap

Clamp the part, wear eye and face protection, and keep gloves away from rotating parts. Guards stay in place on the drill press, and chips get brushed away, never blown toward the face. For more on drill press habits, see drill press safety.

Mistakes that ruin the repair

  • Drilling off center. A hole drilled at an angle leaves a thread that pulls the bolt sideways and an insert that never seats square.
  • Skipping the cutting fluid. A dry tap drags, tears the thread and can snap in the hole.
  • Forcing the tap. A tap that binds often has chips packed in the flutes, and misalignment or the wrong drill size can bind it too. Back it out and clean it instead of leaning on the wrench.
  • Mixing up the pitch. A kit that matches the bolt diameter but not the pitch will not thread correctly and will bind or cross-thread. Match diameter and pitch with a gauge before drilling.

FAQ for welders

Can a thread repair kit fix a hole in aluminum?

Yes, inserts suit aluminum housings and brackets, and the soft metal taps easily with cutting fluid. Clamp the part well, since aluminum grabs a drill bit and can spin the work.

What size drill bit does a thread repair kit need?

Use the drill size the kit specifies for its tap, and use a tapping drill chart to confirm it. See the drilling and tapping chart for how to read it. Never guess the size: a bit that is too small leaves excess metal for the tap to cut and raises the risk of a broken tap, and a bit that is too large leaves a shallow, weak thread.

Will the repaired thread hold as well as the original?

A wire insert engages the parent metal on a larger thread than the original bolt thread, so how well it holds depends on the parent metal, the insert length and a clean, square tapped hole. A well seated insert in a clean hole holds a bolt for ordinary service. For steering, suspension, brakes or other safety critical joints, have a qualified mechanic or machinist check the work before the part goes back into service.

Can I use a thread repair kit on a blind hole?

Yes, with care. Drill deep enough for the insert to seat with clearance for the tap, clear chips often, and remove the tang after the insert seats so it does not block the bolt. A blind hole traps chips at the bottom, so back the tap out often and brush the flutes clean.

What if the tap breaks in the hole?

Stop and do not force the stub. A broken tap is hardened steel, and an extractor made for screws and bolts will not turn it out. Tap removal calls for a tap extractor or machinist help, and drilling at it with a standard bit risks the hole. For broken bolts and screws, a different job, see the screw extractor set how to use guide and the best bolt extractor set roundup.

Related: best drill bit set for metal, types of drill bit, and the Metal Fab Tools hub. Also see the best drill bit set for hard steel guide.

More buying guides

Metal Fab Tools ·

Cutting Torch Repair Kit: What to Buy

A cutting torch repair kit restores a leaking hose or a worn torch with seals, fittings and ferrules, and the right kit depends on…

Metal Fab Tools ·

Propane Regulator Repair Kit: What to Buy

A propane regulator repair kit covers the seals, hose and fittings that wear out first, and this guide shows what to check before ordering…

Welding Consumables ·

Welding Hose Repair Kit: What to Buy

A welding hose repair kit lets you cut out a damaged section of oxy acetylene hose and crimp on new fittings, and the right…