Screw Extractor Set How to Use: Drill, Seat and Turn It Out
A stripped screw or broken bolt comes out with a left-hand bit, a seated extractor and a slow turn in reverse, and this guide shows the steps and the sets for the job.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
NEIKO 01925A Screw-Extractor And Left-Hand9.5/10View on Amazon - 2
72Pcs Bolt Extractor Kit,Left Hand Drill Bit,Easy9.5/10View on Amazon - 3
YEKEPRO 40 Pcs Broken Bolt Extractor Kit with Easy9.4/10View on Amazon - 4
Gifts for Men, Damaged Screw Extractor Set9.3/10View on Amazon
A screw head strips out during a repair, and the fastener sits flush with the surface, with no grip left for a driver. A broken bolt can do the same, snapping off below the surface and leaving a stub that pliers cannot reach. This guide covers screw extractor set how to use, from drilling a pilot hole with a left-hand bit to seating the extractor and turning the broken fastener out in reverse.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

NEIKO 01925A Screw-Extractor And Left-Hand
A 10-piece set of cobalt-fortified HSS left-hand bits with matching alloy spiral extractors in a labeled metal index case.
Pros
- Left-hand bits in 5/64, 7/64, 5/32, 1/4 and 19/64 inch, each with a matching extractor
- Cobalt-fortified HSS bits for durability, per the listing
- Spiral flutes dig in and grip harder as torque is applied
- Metal index case with every size clearly labeled
Cons
- No warranty term is stated
- Largest bit is 19/64 inch, so bigger fasteners need a larger set
- No drill speed guidance in the listing
- Covers spiral extractors only, with no socket or multi-spline styles

72Pcs Bolt Extractor Kit,Left Hand Drill Bit,Easy
A 72-piece kit with left-hand bits, multi-spline and spiral extractors, socket adapters, nut splitters and a center punch.
Pros
- 72 pieces, the widest kit here, with 13 multi-spline and 6 spiral extractors
- Titanium-coated HSS bits with a 135° angle for easier cutting
- Sizes from 1/4 to 3/4 inch in SAE and metric
- Includes 3/8 inch hex socket adapters, nut splitters, extension bar and center punch
Cons
- No warranty term is stated
- No storage case is mentioned in the listing
- The listing gives no count for the left-hand drill bits
- The 72-piece count includes adapters and accessories, not 72 extractors

YEKEPRO 40 Pcs Broken Bolt Extractor Kit with Easy
A 40-piece set of socket, multi-spline and spiral extractors with left-hand cobalt bits for stripped, broken and rusted fasteners.
Pros
- 40 pieces: 15 socket, 10 multi-spline, 10 left-hand bits and 5 spiral extractors
- Chrome molybdenum steel extractors and HSS bits with titanium coating
- Covers stripped, broken, damaged, rounded and rusted fasteners
- The listing gives a seating tip: strike the extractor with a hammer so it grips
Cons
- No warranty term is stated
- No case is mentioned in the listing
- No extractor or bit sizes are stated
- No socket drive size is stated

Gifts for Men, Damaged Screw Extractor Set
A 6-piece spiral extractor set in heat-treated steel with a metal storage case, for stripped screws, nuts and bolts.
Pros
- Hardened, heat-treated steel with a corrosion-resistant finish
- Spiral design grips tight and removes stripped screws, per the listing
- Metal storage case keeps the set organized
- The listing warns to slow the drill speed so the extractor is not damaged
Cons
- No warranty term is stated
- Only 6 pieces, the smallest set here
- No extractor sizes are stated
- The claim of removing screws in seconds has no stated basis
Screw extractor set how to use
The job has a set order: drill, seat, turn. The seating step is what makes the extractor bite instead of spin. A left-hand bit drills the pilot hole while turning in reverse, so a loose stub can spin out on the bit alone. Then the extractor goes into the hole and bites, and steady reverse pressure turns the fastener out.
- Drill a pilot hole in reverse. Fit a left-hand bit and run the drill in reverse, slowly. The QIZRON listing warns to slow the drill speed, or the extractor can be damaged. A left-hand bit turns the fastener the way it unscrews, so a loose stub can spin out on the bit alone.
- Seat the extractor. Strike the extractor into the hole so the flutes bite. YEKEPRO advises striking the extractor with a hammer so it grips and does not spin without biting.
- Turn it out. Turn the extractor in reverse with a wrench or socket and keep steady pressure so the spiral flutes dig in harder as resistance rises. NEIKO describes the spiral flutes digging in and increasing grip as torque is applied, and coobeast describes the same grip building as resistance increases.
Pick the right size first
Size is the whole job. NEIKO lists left-hand bits from 5/64 inch to 19/64 inch, with a matching extractor for each bit, and the set holds 10 pieces in a metal index case with every size labeled. The coobeast kit (on Amazon) lists sizes from 1/4 inch to 3/4 inch, in SAE and metric, with 13 multi-spline extractors and 6 spiral extractors that reach deeper places. YEKEPRO packs 40 pieces, with socket, multi-spline and spiral extractors plus left-hand cobalt bits, for stripped, broken, damaged, rounded and rusted fasteners. QIZRON keeps it to 6 pieces, with a metal storage case.
What to watch while you work
Clamp the work before drilling, wear eye protection, and keep gloves away from the spinning bit. A broken extractor is harder to remove than the screw it was meant to save, so slow down and let the bit cut instead of forcing it. The QIZRON listing states this plainly: slow the drill speed, or the extractor can be damaged. Keep the bit straight in the hole, and stop if the extractor starts to slip instead of bite. OSHA machine guarding covers rotating parts on shop machines, and the same care applies on a bench drill or a hand drill.
The sets side by side
| Set | Pieces | Extractor styles | Steel | Case |
|---|---|---|---|---|
| NEIKO 01925A | 10 | Spiral flute, alloy | Cobalt-fortified HSS M2 | Metal index case, sizes labeled |
| coobeast 72-Piece | 72 | Multi-spline and spiral | HSS, titanium coating; Cr-Mo | Not stated |
| YEKEPRO 40-Piece | 40 | Socket, multi-spline and spiral | HSS, titanium coating; Cr-Mo | Not stated |
| QIZRON 6-Piece | 6 | Spiral | Heat-treated steel | Metal storage case |
The NEIKO set is the most clearly matched of the group, with each bit matched to an extractor. The coobeast kit is the widest, with multi-spline and spiral extractors plus socket adapters and a center punch. YEKEPRO sits between them on piece count, and QIZRON is the small kit of the group.
Screw extractor sets for stripped screws and broken bolts
The drilling and turning steps above need a left-hand bit and a matching extractor. The sets below supply those parts, and the smallest set supplies extractors only.
FAQ for welders
Can a screw extractor remove a bolt broken below the surface?
Yes, if a pilot hole can be drilled into the broken stub. Drill in reverse with a left-hand bit, seat the extractor so the flutes bite, and turn it out in reverse. If the stub is flush or below the surface, a center punch helps start the bit in the middle of the fastener.
Do I need a left-hand drill bit, or will a normal bit work?
A left-hand bit is the right tool for this job. It turns in reverse, the direction the fastener unscrews, so a loose stub can spin out while drilling. A normal bit turns the other way and can tighten a broken bolt further into the hole.
What size extractor do I need?
Match the extractor to the fastener, and match the bit to the extractor. NEIKO pairs each bit with an extractor, and coobeast marks each multi-spline extractor with a laser etch so the size is easy to read. A size that is too small may not grip well enough to hold, and a size that is too large will not fit the hole the bit drills.
Why did my extractor slip or break?
Check the size, the drill speed and the seating. The QIZRON listing warns to slow the drill speed, or the extractor can be damaged, and YEKEPRO advises striking the extractor with a hammer so it grips before turning. If the extractor slips, stop and reseat it instead of forcing it.
Can I use a screw extractor on wood screws?
Yes, for a stripped or broken wood screw the same steps apply. YEKEPRO lists wood screws among the fasteners its set suits, and coobeast states its extractors work on wood or metal. Drill in reverse, seat the extractor, and turn the screw out slowly.
Related: best screw extractor set, best twist drill bit set, and the screw extractor set how to use hub. Also see the Gear Score method.




