Best Twist Drill Bit Set (2026): 5 Picks for Wood, Plastic and Thin Metal
Titanium-coated HSS twist drill bit sets from 3 to 13 mm, compared on size range, shank type, serrated side cutting and storage.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallJONMON 10-Pack 3-13mm9.5/10View on Amazon - 2
Best 6-Piece SetJONMON 6-Pack 3-8mm9.5/10View on Amazon - 3
Best Hex ShankHUBANGBIAO 5-Piece Hex Shank9.4/10View on Amazon - 4
Most CompactGrevosea 6-Pack 3-8mm9.4/10View on Amazon
A bracket needs holes in a new spot, or a sheet of thin metal needs a slot for a bolt to slide in. A twist drill bit set that covers the small sizes and steps up cleanly saves a trip back to the bench for a different bit. This guide compares twist drill bit sets on what each listing states: size range, material, shank type, serrated side cutting and storage, and names the best twist drill bit set for a home fab shop.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall JONMON 10-Pack 3-13mm: 10 sizes from 3 to 13 mm, a 135° split point, serrated side cutting and a portable bag. Check price on Amazon
- Best 6-Piece Set JONMON 6-Pack 3-8mm: 6 sizes from 3 to 8 mm with the same 135° split point and serrated side cutting. Check price on Amazon
- Best Hex Shank HUBANGBIAO 5-Piece Hex Shank: 1/4 inch hex shank for quick-change chucks and impact drivers, with a plastic storage case. Check price on Amazon
- Most Compact Grevosea 6-Pack 3-8mm: A compact 6-piece set from 3 to 8 mm with serrated side cutting and an oil-coated surface. Check price on Amazon
The machines

JONMON 10 Pack 3-13mm Titanium Coated HSS Serrated
Ten titanium-coated HSS bits from 3 to 13 mm with a 135° split point, serrated side cutting and a portable bag.
Pros
- 10 sizes from 3 to 13 mm, the widest range here
- 135° split point with a round shank that fits most drills
- Serrated side cutting for grooves and slots after drilling
- Fully ground spiral groove design for cooler drilling
Cons
- Grooving guidance caps cutting use at 8 mm, so the 9 to 13 mm bits are for drilling only
- Needs a 24V or higher cordless drill, or a 350W or higher corded drill
- No storage case, only a plastic bag
- No warranty term in the listing

JONMON 6 Pack Titanium Coated HSS Twist Drill Bits
Six titanium-coated HSS bits from 3 to 8 mm with a 135° split point, serrated side cutting and a portable bag.
Pros
- 6 sizes from 3 to 8 mm, the common small-hole range
- 135° split point with a round shank that fits most drills
- Serrated side cutting for grooves and slots after drilling
- Fully ground spiral groove design for cooler drilling
Cons
- No sizes above 8 mm
- Needs a 24V or higher cordless drill, or a 350W or higher corded drill
- No storage case, only a plastic bag
- No warranty term in the listing

5Pcs Titanium Coated HSS Twist Drill Bit Set
Five titanium-coated HSS bits from 1/8 to 5/16 inch with a 1/4 inch hex shank for quick-change chucks, in a plastic storage case.
Pros
- 1/4 inch hex shank locks into quick-change chucks and impact drivers
- Plastic storage case in the box
- 135° point tip for fast, clean holes in wood and plastic
- Serrations break up chips for faster drilling
Cons
- Only 5 sizes, 1/8 to 5/16 inch
- Not recommended for hard metals or masonry
- Thin metal limit of under 2 mm
- No warranty term in the listing

Grevosea 6 Pack Twist Drill Bit Set
Six titanium-coated HSS bits from 3 to 8 mm with serrated side cutting, a hex shank and an oil-coated surface.
Pros
- 6 sizes from 3 to 8 mm, the common small-hole range
- Maker claims the titanium coating doubles lifespan over standard bits
- Serrated side cutting for chip discharge
- Fully ground spiral groove design for cooler drilling
Cons
- Listing states both a hex shank and a straight shank
- Surface arrives oil-coated to prevent rust, so wipe bits before use
- No case or bag stated in the listing
- No warranty term in the listing

6pcs High-Speed Steel Metalworking Set
Six bits from 3 to 8 mm with a 135° split tip and serrated side cutting, sold as an M35 cobalt set.
Pros
- 6 sizes from 3 to 8 mm, the common small-hole range
- 135° split-tip straight shank for precise starts
- Serrated edge for horizontal cutting after drilling
- Round straight shank fits most corded and cordless drills
Cons
- No storage case or bag stated
- No warranty term in the listing
- No drill power guidance stated for grooving
Other welders and gear to compare
Titanium Coated HSS Twist Drill Bit Set for MetalCheck price on Amazon
19 Pcs HSS Titanium Twist Drill Bit SetCheck price on Amazon
Cobalt Drill Bit SetCheck price on Amazon
BECOLLO 60pcs Titanium Drill Bit SetCheck price on Amazon
Hex Shank Twist Drill Bit Set 13PCSCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Sizes | Material | Shank | Side cutting | Storage |
|---|---|---|---|---|---|---|
| JONMON 10-Pack 3-13mm | 9.5/10 | 10 sizes, 3 to 13 mm | HSS, titanium coated | Round | Serrated | Plastic bag |
| JONMON 6-Pack 3-8mm | 9.5/10 | 6 sizes, 3 to 8 mm | HSS, titanium coated | Round | Serrated | Plastic bag |
| HUBANGBIAO 5-Piece Hex Shank | 9.4/10 | 5 sizes, 1/8 to 5/16 in | HSS, titanium coated | 1/4 in hex | Serrated | Plastic case |
| Grevosea 6-Pack 3-8mm | 9.4/10 | 6 sizes, 3 to 8 mm | HSS, titanium coated | Hex, straight also stated | Serrated | Not stated |
| Generic M35 6-Piece | 9.3/10 | 6 sizes, 3 to 8 mm | HSS, titanium coated | Round | Serrated | Not stated |
All specs here repeat what the maker rates and the listing prints, copied down 6 November 2026.
Buying guide: choosing the best twist drill bit set
Size range
The sets here span 3 to 13 mm. The JONMON 10-pack is the only set with sizes above 8 mm, running to 13 mm, while the other four sets top out at 8 mm. The HUBANGBIAO set lists its sizes in inches, 1/8 to 5/16 inch, which the listing gives as 3 to 8 mm. Pick the range that covers the holes you drill most, and keep the size list beside the drill so you reach for the right bit.
Shank type
The shank decides which chuck holds the bit. The JONMON sets and the Generic set use a round shank, which the listings say fits most electric drills and bench drills. The HUBANGBIAO set uses a 1/4 inch hex shank for quick-change chucks and impact drivers. The Grevosea listing states both a hex shank and a straight shank, so confirm the shank before you buy.
Side cutting and grooving
Every set here has serrated sides that keep cutting horizontally after the hole is drilled, for grooves and slots. The JONMON sets say to saw counter-clockwise to the drill rotation, at low speed and high torque, and not to use bits larger than 8 mm for cutting. The HUBANGBIAO and Grevosea sets also list serrated side cutting, with the Grevosea serrations breaking up chips for better discharge.
Storage
A case or bag keeps small bits together. The HUBANGBIAO set comes in a plastic storage case, and the two JONMON sets come in a portable plastic bag. The Grevosea and Generic listings state no case or bag, so plan your own storage for those bits.
Use as directed. Clamp the work before drilling, keep hands clear of the bit, and wear eye protection. Check the shank and the bit size before you start, and follow the maker’s grooving guidance on speed and drill power. See the Safety Disclaimer.
Before You Strike an Arc
- Check the shank in your chuck: round on the JONMON and Generic sets, 1/4 inch hex on the HUBANGBIAO, and stated both ways on the Grevosea.
- For grooving with the JONMON sets, the maker calls for a 24V or higher cordless drill or a 350W or higher corded drill.
- Wipe the oil coating off the Grevosea bits before first use.
- Count the bits on arrival: 10 in the JONMON 10-pack, 6 in the 6-piece sets, 5 in the HUBANGBIAO set.
- Confirm the material claim on the Generic set, since its title says M35 cobalt and its bullets say titanium-coated high-speed steel.
FAQ for welders
How do I fit a drill bit in the chuck?
Match the shank to the chuck. The JONMON sets and the Generic set use a round shank that fits most electric drills and bench drills. The HUBANGBIAO set uses a 1/4 inch hex shank that locks into a quick-change chuck or an impact driver. The Grevosea listing states both a hex shank and a straight shank, so check the shank on arrival.
What is the best twist drill bit set here?
The JONMON 10-pack is the top pick here, with 10 sizes from 3 to 13 mm, a 135° split point and serrated side cutting. The JONMON 6-pack matches it on features with 6 sizes from 3 to 8 mm. Pick the 10-pack when you need bits above 8 mm, and the 6-pack when small holes cover the job.
How do I use the serrated side cutting?
Drill the hole first, then let the serrated side cut horizontally, sawing counter-clockwise to the drill rotation on the JONMON sets. Use low speed and high torque for cutting, and start with a smaller bit when cutting from an edge. The JONMON guidance does not recommend bits larger than 8 mm for cutting.
What size drill bit should I use?
Match the bit to the hole you need, and start small when cutting from an edge, since the bit can slip without a fixed point. The sets here cover 3 to 13 mm, with the JONMON 10-pack reaching 13 mm and the other sets topping out at 8 mm. For thin wood slotting, the JONMON sets list 1 to 2 mm thin wood.
Can these drill bits drill metal?
The listings name aluminum, thin iron sheet, copper tubes and thin metal under 2 mm, depending on the set. The HUBANGBIAO set is not recommended for hard metals or masonry. The Generic set’s title says M35 cobalt while its bullets describe titanium-coated high-speed steel, so treat its material as the bullets describe it.
Related: best drill bit set for wood and metal, best cobalt drill bit set, titanium vs black oxide drill bits, carbide vs cobalt drill bits, and the metal fab tools hub.
Scoring, line by line
Each set is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on the How We Pick page. Drill bit sets have no electrical safety listing to state, and no listing here states a warranty, so every set here scores zero on those two criteria; the ranking comes from the other three.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| JONMON 10-Pack 3-13mm | 9.5 | 30 | 21 | 22 | 0 | 0 |
| JONMON 6-Pack 3-8mm | 9.5 | 29 | 21 | 21 | 0 | 0 |
| HUBANGBIAO 5-Piece Hex Shank | 9.4 | 28 | 20 | 21 | 0 | 0 |
| Grevosea 6-Pack 3-8mm | 9.4 | 27 | 19 | 20 | 0 | 0 |
| Generic M35 6-Piece | 9.3 | 26 | 18 | 19 | 0 | 0 |
A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number.




