Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Step Drill Bit vs Twist Drill Bit: Which One Should You Buy?

Step drill bits and twist drill bits compared for the shop: two step bits and two twist sets on hole sizes, point angles, materials and what each listing leaves unclear.

Step Drill Bit vs Twist Drill Bit: Which One Should You Buy?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 199 Pieces Titanium Twist Drill Bit Set99 Pieces Titanium Twist Drill Bit Set9.6/10View on Amazon
  2. 23/16"-7/8" M2 Step Drill Bit Unibit for Hole3/16"-7/8" M2 Step Drill Bit Unibit for Hole9.6/10View on Amazon
  3. 3JONMON 8 Pack 3-10mm Titanium Coated HSS TwistJONMON 8 Pack 3-10mm Titanium Coated HSS Twist9.6/10View on Amazon
  4. 4COMOWARE Step Drill Bit Set for Metal HSS 5PcsCOMOWARE Step Drill Bit Set for Metal HSS 5Pcs9.5/10View on Amazon

Verdict. Pick step drill bits for varied hole sizes in sheet goods: the Jerax example drills 12 sizes with one bit. Pick twist drill bits for full size coverage and woodworking: the HURRICANE example packs 99 bits from 1/16 to 3/8 inch. The COMOWARE set disagrees with itself on sizes, so verify the count before you buy.

Sheet metal on the bench needs a clean, round hole, and the bit you grab decides how fast you get it. Step drill bit vs twist drill bit is the choice between one bit that drills many sizes and a full index of bits that each drill one. This comparison puts two step bits against two twist sets on what each listing states.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

The four bits

99 Pieces Titanium Twist Drill Bit Set

99 Pieces Titanium Twist Drill Bit Set

HURRICANE9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 99-piece titanium-coated twist drill set from 1/16 to 3/8 inch with a 135-degree tip, for wood, metal and plastic.

Pros

  • 99 bits covering 1/16 to 3/8 inch, per the listing.
  • 135-degree fast-cutting point, self-centering with less pressure.
  • Titanium coating for hardness and less heat buildup.
  • Plastic storage box included, per the bullets.

Cons

  • Included Components says Bare-Tool against the box claim.
  • No warranty term is stated.
  • Each hole size needs its own bit, unlike step bits.
3/16"-7/8" M2 Step Drill Bit Unibit for Hole

3/16"-7/8" M2 Step Drill Bit Unibit for Hole

Jerax tools9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A single M2 high-speed steel step bit with 12 marked sizes from 3/16 to 7/8 inch, for stainless, copper, aluminum, wood and plastic.

Pros

  • 12 marked sizes in one bit, 3/16 to 7/8 inch.
  • M2 high-speed steel with vacuum heat treatment and nitride hardening, per the bullets.
  • Cuts stainless up to 12ga / 2.7mm thick, per the listing.
  • Polished steps with size highlights, no stopping to check size.

Cons

  • Single bit; a full set costs more.
  • Straight shank, no flats against slippage.
  • No warranty term is stated.
  • No rating past 7/8 inch.
JONMON 8 Pack 3-10mm Titanium Coated HSS Twist

JONMON 8 Pack 3-10mm Titanium Coated HSS Twist

JONMON9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

Eight titanium-coated twist bits from 3 to 10mm with serrated side-cutting edges, for drilling and slotting wood, plastic, aluminum and thin metal.

Pros

  • 8 sizes from 3mm to 10mm in a portable case.
  • 135-degree split point for precise starts without walking.
  • Serrated side edges cut grooves and slots, per the listing.
  • Titanium-coated HSS with spiral grooves for less heat.

Cons

  • Grooving needs 24V+ or 350W+ drills; smaller drills are not recommended, per the listing.
  • Side cutting only in the counter-clockwise direction, per the bullets.
  • No warranty term is stated.
  • Metric only; no inch sizes listed.
COMOWARE Step Drill Bit Set for Metal HSS 5Pcs

COMOWARE Step Drill Bit Set for Metal HSS 5Pcs

COMOWARE9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-piece titanium-coated step bit set with tri-flat shanks and an aluminum case, for steel, wood and plastic.

Pros

  • Five bits with laser-etched size marks in an aluminum case.
  • Titanium-coated HSS with 2 straight flutes for chip removal.
  • Tri-flat shanks grip tight and resist slippage.
  • Split point with a 118-degree cutting angle.

Cons

  • No warranty term is stated.
  • The contradictions make the size count hard to trust.

Other welders and gear to compare

Side by side

HURRICANE 99-pc twist set Jerax M2 step bit JONMON 8-pack twist set COMOWARE 5-pc step set
Side Twist drill bit Step drill bit Twist drill bit Step drill bit
Pieces 99 1 bit, 12 sizes 8 5
Size range 1/16 to 3/8 in 3/16 to 7/8 in 3 to 10 mm 3/16 to 1-3/8 in
Point angle 135 degrees 118 degrees 135 degrees 118 degrees
Material HSS, titanium M2 HSS, nitride HSS, titanium HSS, titanium
Shank Straight Straight Round 3-flat
Specialty Full size range 12 sizes in one bit Serrated side cutting Cased set
Flutes Spiral 2 straight Spiral groove 2 straight
Case Plastic box Not stated Portable case Aluminum case

All specs here repeat what the maker rates and the listing prints, copied down 22 October 2026. None of the four listings states a warranty term.

Hole sizes: one bit or many

The Jerax example drills 12 sizes from 3/16 to 7/8 inch with a single bit. The COMOWARE example claims 28 sizes from 3/16 to 1-3/8 inch in its bullets, though its title says 50. The HURRICANE example covers 1/16 to 3/8 inch across 99 bits, and the JONMON example covers 3 to 10mm across 8 bits. If you drill the same size all day, a twist bit is fine; if every hole is different, a step bit saves bit changes.

Point angles and starts

The step examples use a 118-degree point; the twist examples use 135-degree points that the listings say start without walking. The COMOWARE step set names a center punch in its title for marking starts. Only the twist listings describe centered, no-walk starts; the step listings make no such claim.

Materials and coatings

Three examples are high-speed steel with a titanium-family coating; the Jerax example is M2 steel with a nitride finish instead. The listings on both sides claim longer life from their coatings. With no wear figures stated anywhere, treat coating claims as the maker word, not a measured win.

Shanks and grip

The COMOWARE example lists 3-flat shanks against slippage; the JONMON example lists a round shank; the Jerax and HURRICANE examples list straight shanks. Only the COMOWARE listing makes an anti-slip claim, so the other three leave grip unclear rather than losing the point.

Thin stock or deep holes

Step bits shine in thin stock: the Jerax example rates stainless to 12ga / 2.7mm, and the COMOWARE example targets sheet, aluminum, wood and plastic. Twist bits go deeper: the HURRICANE and JONMON examples list wood, plastic and metal, while step bits are made for thin stock like the Jerax 12ga / 2.7mm rating. Match the bit to the stock thickness, not just the hole diameter.

What the listings leave unclear

The COMOWARE listing disagrees with itself on sizes and piece count. The HURRICANE spec table says 15, 2 pieces against the 99-piece title. The JONMON and Jerax listings are consistent on their counts. When a listing leaves a spec unclear, that counts against it, not as a win for the other side. The JONMON listing, by contrast, states its 8 sizes, its 24V grooving rule and its counter-clockwise cutting direction in full.

Choose step drill bits if

  • You drill varied hole sizes in sheet metal and hate changing bits.
  • You work stainless within the rated thickness, like the Jerax 12ga rating.
  • You want one bit that covers a range instead of a full index.

Choose twist drill bits if

  • You want every common size on hand, like the 99-piece HURRICANE set.
  • You drill mostly wood, plastic and thin stock.
  • You need metric sizes, like the JONMON 3 to 10mm range.

Step drill bit vs twist drill bit: which should you buy?

For sheet metal and varied holes, the step side wins on convenience: the Jerax example is the cleanest listing of the four. For general shop drilling across materials, the twist side wins on coverage: the HURRICANE example puts 99 pieces in one box. Skip the COMOWARE set until its size count reads the same in the title and the bullets.

Before You Strike an Arc

  • Clamp the work; sheet metal grabs bits.
  • The COMOWARE set names a center punch in its title; punch the mark for accurate starts.
  • Wear eye protection; metal chips fly.
  • Check the bit size against the marked steps before drilling.

FAQ for welders

Can a step bit drill wood?

The COMOWARE and Jerax listings name wood among their materials. Step bits cut clean holes in wood and plastic. For deep holes in thick wood, a twist bit clears chips better.

What is the largest hole these bits drill?

The Jerax example goes to 7/8 inch; the COMOWARE bullets claim 1-3/8 inch. The HURRICANE twist set tops out at 3/8 inch and the JONMON at 10mm.

Do I need a special drill for step bits?

No. The listings describe standard shanks for pistol drills and drill presses. The JONMON grooving work wants 24V or higher drills, per its listing.

Are titanium-coated bits better?

Three listings claim longer life from titanium coatings, as the maker claim. The Jerax example uses M2 steel with nitride instead. No listing gives wear figures, so compare on stated specs.

Can twist bits enlarge holes?

The JONMON example has serrated side-cutting edges for enlarging holes and cutting slots, per its listing. Standard twist bits cut on the tip only.

Which side is better for stainless steel?

The Jerax step example rates stainless to 12ga / 2.7mm thick. The HURRICANE twist listing names steel among its materials but gives no thickness. For thin stainless, the step bit rating is the clearer claim.

Related: best step drill bit for sheet metal, titanium vs cobalt drill bits, best drill bits for steel, and step drill bit vs hole saw for sheet metal.

Scoring, line by line

All four bits are scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
HURRICANE 99-pc twist set 9.6 29 20 22 n/a 0
Jerax M2 step bit 9.6 28 21 20 n/a 0
JONMON 8-pack twist set 9.6 28 20 20 n/a 0
COMOWARE 5-pc step set 9.5 27 20 20 n/a 0

A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.

More buying guides