Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Step Drill Bit for Thick Metal (2026): 5 Picks Compared

Five step drill bits compared by steel, coating, flutes, step sizes and stainless limits, from M35 cobalt bits to M2 high-speed steel.

Best Step Drill Bit for Thick Metal (2026): 5 Picks Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1toolant M35 Step BitBest Overalltoolant M35 Step Bit9.7/10View on Amazon
  2. 2SHARPTOOL M2 Step BitWidest RangeSHARPTOOL M2 Step Bit9.7/10View on Amazon
  3. 3EZARC M35 Step Bit SetBest SetEZARC M35 Step Bit Set9.6/10View on Amazon
  4. 4Jerax Quick Change Step BitMost SizesJerax Quick Change Step Bit9.6/10View on Amazon

A thick stainless panel needs a clean hole, and a twist bit walks, grabs or burns out before the hole is round. The best step drill bit for thick metal cuts the hole in steps, so each size lands where the mark is. This guide compares step bits by steel, coating, flutes, step sizes and the stainless thickness each maker lists, using only what each listing states.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall toolant M35 Step Bit: M35 cobalt, TiAlN at 89HRC, 9 sizes and four spiral flutes Check price on Amazon
  • Widest Range SHARPTOOL M2 Step Bit: 10 sizes from 1/4 to 2 inches, split point, no pilot hole Check price on Amazon
  • Best Set EZARC M35 Step Bit Set: 3 M35 cobalt bits, AlTiN at 89HRC, with a storage case Check price on Amazon
  • Most Sizes Jerax Quick Change Step Bit: 12 marked sizes, quick-change hex shank, impact-ready Check price on Amazon

The machines

toolant M35 Cobalt Step Drill Bit, 1/4"-3/4"

toolant M35 Cobalt Step Drill Bit, 1/4"-3/4"

AugTouf9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An M35 cobalt step bit with a TiAlN coating, four spiral flutes and 9 step sizes from 1/4 to 3/4 inch on a 1/4 inch hex shank.

Pros

  • M35 cobalt HSS
  • TiAlN coating rated at 89HRC
  • 9 step sizes from 1/4 to 3/4 inch
  • Four spiral flutes for a faster cut

Cons

  • Cuts sheet to 1/8 inch thick
  • 9 sizes, fewer than the Jerax 12 sizes
  • No warranty term is stated
  • Hex shank, not a tri-flat shank
SHARPTOOL M2 HSS Step Drill Bit Unibit, 1/4"-2"

SHARPTOOL M2 HSS Step Drill Bit Unibit, 1/4"-2"

SHARPTOOL9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An M2 high-speed steel step bit with 10 step sizes from 1/4 to 2 inches, double flutes and a split point tip that needs no pilot hole.

Pros

  • 10 step sizes to 2 inches
  • Split point tip, no pilot holes
  • Double flutes for faster cutting
  • Tri-flat shank fits impact drivers

Cons

  • No warranty term is stated
  • M2 steel, not M35 cobalt
  • Largest size of 2 inches, more than small jobs need
  • Double flutes, fewer than the four-flute bits
EZARC M35 Cobalt Step Drill Bit Set

EZARC M35 Cobalt Step Drill Bit Set

EZARC9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3-piece M35 cobalt step bit set from 1/8 to 7/8 inch with an AlTiN coating, triple flutes and a storage case.

Pros

  • 3 bits from 1/8 to 7/8 inch
  • M35 cobalt HSS
  • AlTiN coating rated at 89HRC
  • Storage case included

Cons

  • Stainless steel only to 1 mm thick
  • Do not use in impact mode
  • Needs cutting oil or coolant for continuous use
  • Triple flutes, fewer than the four-flute bits
Jerax tools 3/16"-7/8" Quick Change M2 Step Drill

Jerax tools 3/16"-7/8" Quick Change M2 Step Drill

Jerax tools9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An M2 step bit with 12 marked sizes from 3/16 to 7/8 inch, double straight flutes and a quick-change 1/4 inch hex shank.

Pros

  • 12 marked sizes from 3/16 to 7/8 inch
  • Quick-change 1/4 inch hex shank
  • Works with impact-ready power tools
  • Cuts stainless steel to 12ga, 2.7mm

Cons

  • Double straight flutes, not spiral flutes
  • M2 steel, not M35 cobalt
  • One bit only, while the EZARC set has 3 bits
  • No TiAlN coating like the M35 bits
Jerax tools 1/4"-3/4" M2 Step Drill Bit Unibit

Jerax tools 1/4"-3/4" M2 Step Drill Bit Unibit

Jerax tools9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An M2 step bit with 5 marked sizes from 1/4 to 3/4 inch, 4 spiral flutes and a 3/8 inch tri-flat shank.

Pros

  • 4 spiral flutes
  • 5 marked sizes from 1/4 to 3/4 inch
  • Cuts stainless steel to 12ga, 2.7mm
  • 3/8 inch tri-flat shank locks in the chuck

Cons

  • 5 sizes, fewer than the Jerax 12 sizes
  • M2 steel, not M35 cobalt
  • Not designed for sockets or impact drivers
  • Needs a chuck of 3/8 inch or larger

Other welders and gear to compare

Spec sheet comparison

Step Bit Gear Score Material Sizes Shank Stainless Limit
toolant M35 Step Bit 9.7/10 M35 cobalt HSS 9, 1/4 to 3/4 in 1/4 in hex 1/8 in
SHARPTOOL M2 Step Bit 9.7/10 M2 HSS 10, 1/4 to 2 in 3/8 in tri-flat Not stated
EZARC M35 Step Bit Set 9.6/10 M35 cobalt HSS 3 bits, 1/8 to 7/8 in 1/4 in hex 1 mm
Jerax Quick Change Step Bit 9.6/10 M2 HSS 12, 3/16 to 7/8 in 1/4 in hex 12ga, 2.7mm
Jerax M2 Step Bit 9.6/10 M2 HSS 5, 1/4 to 3/4 in 3/8 in tri-flat 12ga, 2.7mm

All specs here repeat what the maker rates and the listing prints, copied down 18 November 2026.

Buying guide: choosing the best step drill bit for thick metal

Steel and coating

Steel decides how the bit holds up in stainless. The toolant and EZARC bits are M35 cobalt high-speed steel, and the two Jerax bits and the SHARPTOOL bit are M2 high-speed steel. The toolant TiAlN coating and the EZARC AlTiN coating are both rated at 89HRC, while the Jerax bits use vacuum heat treatment with nitride surface hardening and the SHARPTOOL bit has a nitride treatment. The coatings are made to resist heat, wear and corrosion, and the EZARC coating also lists low friction. The Jerax M2 bullets note more tungsten and molybdenum than average step bits, which the maker links to durability. See our hss vs cobalt drill bit guide for more on the two steels.

Step sizes and flutes

Step sizes decide which holes one bit can drill. The Jerax quick-change bit lists 12 marked sizes from 3/16 to 7/8 inch, the SHARPTOOL bit lists 10 sizes to 2 inches, the toolant bit lists 9 sizes, the EZARC set holds 3 bits from 1/8 to 7/8 inch, and the Jerax 1/4 to 3/4 inch bit lists 5 sizes. Flutes move the chips out: the toolant and Jerax 1/4 to 3/4 inch bits have 4 spiral flutes, the EZARC has triple flutes, and the SHARPTOOL and Jerax quick-change bits have double flutes. Polished steps with size highlights on the Jerax bits let you see the target hole size while drilling, so you do not stop mid-hole to check, and the SHARPTOOL bit has high-visibility size marks for the same reason.

Stainless thickness limits

Check the thickness limit before you drill stainless. The Jerax bits list stainless steel to 12ga, 2.7mm, the toolant bit lists 1/8 inch thick stainless steel, and the EZARC set lists stainless steel to 1 mm thick. The SHARPTOOL bit states no thickness limit, so check the maker’s notes for your material before you buy. The EZARC maker also advises cutting oil or coolant for continuous use, and the Jerax maker notes a high-torque impact wrench can chip the cutting edges. See our best cutting oil for drilling metal guide for more on cutting oil.

Shank and chuck fit

The shank must fit the chuck. The Jerax 1/4 to 3/4 inch bit has a 3/8 inch tri-flat shank for a 3-jaw chuck of 3/8 inch or larger, and the SHARPTOOL bit has a 3/8 inch tri-flatted shank that fits an impact driver. The toolant, EZARC and Jerax quick-change bits run a 1/4 inch hex shank, and the Jerax quick-change shank suits impact-ready power tools. A 1/4 inch hex shank also fits a quick-change chuck for fast bit switches. A tri-flat shank locks in the chuck and resists slipping under load, while a hex shank fits a hex chuck for quick changes. The Jerax 1/4 to 3/4 inch bit is not designed for sockets or impact drivers, and the EZARC maker says not to use impact mode.

What comes in the box

Count the bits before you order. The EZARC set holds 3 bits in a storage case, while the other four bits are single bits. The EZARC case keeps the 3 bits organized for transport and storage, so the set suits a bench that moves between jobs.

Use as directed. Clamp the work before you drill, wear eye protection, and keep gloves away from rotating parts. Add cutting oil or coolant for continuous use, as the EZARC maker advises, and check the maker’s notes before using a bit in impact mode. See the OSHA machine guarding and our Safety Disclaimer.

Before You Strike an Arc

  • Check the shank against the chuck: the Jerax 1/4 to 3/4 inch bit needs a 3/8 inch or larger chuck, and the SHARPTOOL bit fits an impact driver.
  • Count the step sizes on arrival: 5 on the Jerax 1/4 to 3/4 inch bit, 9 on the toolant, 10 on the SHARPTOOL and 12 on the Jerax quick-change bit.
  • Add cutting oil or coolant for continuous use, as the EZARC maker advises.
  • Check the stainless limit before you drill: 12ga, 2.7mm on the Jerax bits, 1/8 inch on the toolant and 1 mm on the EZARC set.

FAQ for welders

Can a step drill bit cut thick metal?

Yes, when the maker lists the thickness. A step bit cuts one size at a time as it sinks deeper, so the hole grows in steps rather than in one pass. Step bits also suit thin sheet, where one bit covers several hole sizes without a bit change. The Jerax bits list stainless steel to 12ga, 2.7mm, the toolant bit lists 1/8 inch thick stainless steel, and the EZARC set lists stainless steel to 1 mm thick. Check the limit for your material before you drill.

What is the difference between M2 and M35 step bits?

The toolant and EZARC bits here are M35 cobalt high-speed steel, while the Jerax bits and the SHARPTOOL bit are M2 high-speed steel. The M35 bits list TiAlN and AlTiN coatings rated at 89HRC, and the M2 bits list nitride hardening or a nitride treatment. Both steels cut metal and stainless steel, so the choice comes down to coating, flutes and the thickness limit.

Do step drill bits need a pilot hole?

The SHARPTOOL bit has a split point tip and needs no pilot hole. A split point tip centers itself on the mark, so the bit does not walk before it bites. The other four bits state no pilot hole claim, so check the maker’s notes for your bit before you drill.

Can I use a step drill bit in an impact driver?

The SHARPTOOL bit has a tri-flatted shank that fits an impact driver, and the Jerax quick-change bit suits impact-ready power tools. Check the shank before you buy: a tri-flat shank fits a 3-jaw chuck, and a hex shank fits a hex chuck. The Jerax 1/4 to 3/4 inch bit is not designed for sockets or impact drivers, and the EZARC maker says not to use impact mode.

Related: best drill bit to drill through metal, best drill bits for drilling stainless steel, hss vs cobalt drill bit, and the metal fab tools hub. Also see our drill press safety.

Scoring, line by line

Each step bit is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. None of the five listings names a safety standard or a warranty term, so every bit here scores zero on those two criteria; the ranking comes from the other three.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
toolant M35 Step Bit 9.7 32 22 21 n/a 0
SHARPTOOL M2 Step Bit 9.7 32 21 21 n/a 0
EZARC M35 Step Bit Set 9.6 29 21 22 n/a 0
Jerax Quick Change Step Bit 9.6 30 21 20 n/a 0
Jerax M2 Step Bit 9.6 29 21 20 n/a 0

A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.

More buying guides