Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Step Drill Bit vs Hole Saw for Sheet Metal: Which One Should You Buy?

Two step drill bits and two hole saws for sheet metal compared on hole size range, material thickness, box contents and what each listing leaves unclear.

Step Drill Bit vs Hole Saw for Sheet Metal: Which One Should You Buy?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1EZARC Carbide Hole Saw Heavy DutyEZARC Carbide Hole Saw Heavy Duty9.7/10View on Amazon
  2. 2ZELCAN Large HSS Spiral Groove Step Drill BitZELCAN Large HSS Spiral Groove Step Drill Bit9.6/10View on Amazon
  3. 3HSS Step Drill Bit for Metal, 3/8" Tri-ShankHSS Step Drill Bit for Metal, 3/8" Tri-Shank9.6/10View on Amazon
  4. 46 inch Hole Saw for Wood, Metal6 inch Hole Saw for Wood, Metal9.6/10View on Amazon

Verdict. For step drill bit vs hole saw for sheet metal, pick the step drill bit side if you drill many hole sizes in thin sheet and want one bit to do them all: the ZELCAN example cuts 12 sizes from 1/4 to 2-3/8 in. Pick the hole saw side for a fixed large diameter: the VIKITON cuts a 6 in hole, and the EZARC carbide example is the only one here stated for stainless steel, cutting sheet up to 3/16 in thick.

You need a clean round hole in sheet metal: a conduit entry in a junction box, a grommet hole in a panel, a vent in ductwork. A step drill bit opens one hole out through several sizes; a hole saw cuts one fixed diameter. This step drill bit vs hole saw for sheet metal comparison puts two examples of each side by side on what the listings state: hole range, material and thickness, starting the cut, and what comes in the box.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

The four examples

EZARC Carbide Hole Saw Heavy Duty

EZARC Carbide Hole Saw Heavy Duty

EZARC9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1 in (25 mm) carbide hole saw for stainless steel and sheet metal, cutting material up to 3/16 in thick, with a spring-loaded pilot bit and an all-in-one box.

Pros

  • Carbide teeth stated for stainless steel sheet
  • Cuts material up to 3/16 in thick
  • Spring-loaded pilot bit for clean plug ejection
  • Pilot bit, spring and wrench in the box

Cons

  • Limited to material up to 3/16 in thick
  • No warranty term stated
  • 1 in only; no larger sizes in this listing
  • Weight listed as 124 g, no pounds stated
ZELCAN Large HSS Spiral Groove Step Drill Bit

ZELCAN Large HSS Spiral Groove Step Drill Bit

CO-Z9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A titanium-coated HSS step drill bit with 12 sizes from 1/4 to 2-3/8 in, a spiral groove and a rapid strike tip, for sheet metal, wood, acrylic and PVC.

Pros

  • 12 sizes from 1/4 to 2-3/8 in in one bit
  • Spiral groove with 135-degree step point
  • Titanium-coated HSS, 16 oz listed weight
  • Honest limits: recommends M2/M35 for hard metals

Cons

  • No warranty term stated
  • Brand shows as CO-Z against the ZELCAN title
  • Rapid strike tip speed is the maker's claim
  • Straight shank; no tri-flat grip stated
HSS Step Drill Bit for Metal, 3/8" Tri-Shank

HSS Step Drill Bit for Metal, 3/8" Tri-Shank

COMOWARE9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A titanium-coated HSS step drill bit with 10 sizes from 1/4 to 1-3/8 in, 2 straight flutes and a 3/8 in tri-flat shank, for steel sheet, aluminum, wood and plastic.

Pros

  • 10 sizes from 1/4 to 1-3/8 in on one bit
  • 3/8 in tri-flat shank for grip in pistol drills
  • Laser-etched size markings
  • Split point at 118 degrees, 2 straight flutes

Cons

  • Set name says 10-Piece against a 1-piece count
  • No warranty term stated
  • No max thickness figure stated
  • Straight flutes, not spiral
6 inch Hole Saw for Wood, Metal

6 inch Hole Saw for Wood, Metal

VIKITON9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 6 in (152 mm) bi-metal hole saw with HSS teeth for wood, plastic, drywall and thin metals, shipping with an arbor, two pilot bits and a hex key.

Pros

  • Full kit: saw, arbor, 2 pilot bits, hex key
  • Bi-metal with HSS teeth and flexible steel body
  • 6 in fixed diameter for large holes
  • Detailed pro tips for metal cutting

Cons

  • Explicitly excludes stainless steel
  • No warranty term stated
  • Thin metals only; no thickness figure
  • Table lists a 6 in item thickness that is unclear

Other welders and gear to compare

Step drill bit vs hole saw for sheet metal, side by side

EZARC Carbide Hole Saw ZELCAN Step Drill Bit COMOWARE Step Drill Bit VIKITON 6in Hole Saw
Hole range 1 in fixed 12 sizes, 1/4 to 2-3/8 in 10 sizes, 1/4 to 1-3/8 in 6 in fixed
Material Carbide HSS, titanium coating HSS, titanium coating Bi-metal, HSS teeth
Max thickness stated 3/16 in 0.2 in Not stated Thin metals; no figure
Stainless steel Stated Not recommended by listing Not stated Excluded
Pilot / point Spring-loaded pilot bit Step point, rapid strike tip Split point Arbor with pilot bit
In the box Cutter, pilot bit, spring, wrench 1 bit 1 bit Saw, arbor, 2 pilot bits, hex key

Ratings in this table are the makers’ own claims taken from each product page (21 October 2026). A figure from one listing describes that listing only.

Hole size and range

The step bits cover a range with one tool. The COMOWARE drills 10 sizes from 1/4 to 1-3/8 in, and the ZELCAN drills 12 sizes from 1/4 to 2-3/8 in, with the sizes also listed in millimeters from 6 to 60. The hole saws cut one diameter each: 6 in on the VIKITON and 1 in (25 mm) on the EZARC. One step bit covers many sizes without bit changes; a hole saw cuts one diameter directly.

Material and thickness

Both step bits are titanium-coated high speed steel. The COMOWARE lists steel sheets, aluminum, wood and plastic among its surfaces. The ZELCAN lists acrylic, PVC, wood, aluminum and iron sheets up to 0.2 in thick, but recommends M2 or M35 bits for stainless, high carbon and heat-treated steel instead of itself. The VIKITON is bi-metal with high speed steel teeth for wood, plastic, drywall and thin metals, and it explicitly excludes stainless steel. The EZARC is the stainless pick: carbide teeth for stainless, mild steel, iron, copper and brass sheet, cutting material up to 3/16 in thick, with the maker claiming over 500 holes through stainless and up to 10 times the life of bi-metal saws. See our bi-metal vs carbide hole saw comparison for more on that split.

Starting the cut and clearing chips

The COMOWARE uses 2 straight flutes with a split point at 118 degrees, and laser-etched size markings so you can see which step you are on. The ZELCAN uses a spiral groove with a step point at 135 degrees; its rapid strike tip is claimed to drill twice as fast as the average step drill, with dual flutes stated to clear chips faster. The hole saws start on a pilot: the VIKITON ships an arbor with a pilot drill bit plus a replacement pilot and a hex key, and the EZARC uses a spring-loaded pilot bit stated for fast drilling and clean plug ejection. On metal, the VIKITON listing says to apply water or coolant, reduce feed speed, let the saw cool before touching, and stop on abnormal vibration.

What is in the box

Both step bits ship as single bits: each listing counts 1 piece, though the COMOWARE set name reads 10-Piece against that count; the 10 refers to the hole sizes. The hole saws come kitted: the VIKITON box holds the 6 in saw, an arbor with a drill bit, a replacement pilot bit and a hex key, and the EZARC ships its cutter with a pilot drill bit, spring and wrench, an all-in-one design the listing says needs no extra accessories.

Choose a step drill bit if

  • You drill many hole sizes in thin sheet and want one bit to cover them.
  • You work in aluminum, mild steel sheet, wood or plastic, within the stated sizes.
  • You want the size marked on the bit: the COMOWARE states laser-etched markings.
  • You want a spiral flute and a strike tip: the ZELCAN states both.

Choose a hole saw if

  • You cut the same fixed diameter repeatedly: 6 in on the VIKITON, 1 in on the EZARC.
  • You cut stainless steel sheet: the EZARC is the only one here stated for it.
  • You want the full kit in the box: arbor, pilots and hex key on the VIKITON; pilot, spring and wrench on the EZARC.
  • You want clean plug ejection: the EZARC states a spring-loaded pilot bit for it.

Before You Strike an Arc

  • Clamp the sheet before you cut; the COMOWARE laser-etched steps let you stop at the size you want.
  • Cutting metal with the VIKITON: apply water or coolant and slow the feed, per its listing.
  • Let a hole saw cool before touching it; the VIKITON listing warns the surface runs hot after drilling.
  • Stop at the first sign of abnormal vibration; the VIKITON listing says to stop immediately.

FAQ for welders

Which of these cuts stainless steel sheet?

The EZARC carbide hole saw: its listing states stainless steel, mild steel, iron, copper and brass sheet. The VIKITON explicitly excludes stainless steel. The ZELCAN recommends M2 or M35 bits for stainless and hard metals instead of itself.

How many hole sizes does one step drill bit cover?

The COMOWARE covers 10 sizes from 1/4 to 1-3/8 in, and the ZELCAN covers 12 sizes from 1/4 to 2-3/8 in, also listed as 6 to 60 mm. Both are single bits; neither listing counts more than 1 piece.

What is the thickest sheet these cut?

The ZELCAN lists iron sheets up to 0.2 in thick and the EZARC cuts material up to 3/16 in thick. The COMOWARE and VIKITON listings state no thickness figure; the VIKITON describes its metal range as thin metals.

What comes in the box with each hole saw?

The VIKITON ships the 6 in saw with an arbor and drill bit, a replacement pilot bit and a hex key. The EZARC ships its 1 in cutter with a pilot drill bit, spring and wrench, which its listing calls an all-in-one design.

Do the step drill bits fit a regular drill?

The COMOWARE has a 3/8 in tri-flat shank stated for secure clamping in pistol drills. The ZELCAN listing states compatible drill diameters for standard pistol drills; check its spec table. Both are single bits, not sets.

Related: the best step drill bit for sheet metal, the best hole saw for stainless steel and our best hole saw for metal guide.

Scoring, line by line

Each example is scored on performance, build, value, safety and warranty, using only what the listing publishes, with the weights on our How We Pick page.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
EZARC Carbide Hole Saw 9.7 30 22 21 n/a 0
ZELCAN Step Drill Bit 9.6 29 21 21 n/a 0
COMOWARE Step Drill Bit 9.6 28 21 21 n/a 0
VIKITON 6in Hole Saw 9.6 27 20 22 n/a 0

The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure. Safety points apply to gear that runs on power or lists safety features. Without either, we score out of 90 instead of 100.

More buying guides