Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Hole Saw for Stainless Steel (2026): 5 Picks Compared

Five hole saws for stainless steel, compared on stated size, cutter type, capacity and count, so your teeth match your stock.

Best Hole Saw for Stainless Steel (2026): 5 Picks Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1EZARC Carbide 1-1/8inBest OverallEZARC Carbide 1-1/8in9.6/10View on Amazon
  2. 2METOTY 33pc TCT KitBest KitMETOTY 33pc TCT Kit9.6/10View on Amazon
  3. 3DECKRKAT 2in TCT 2-PackBest 2-Inch PickDECKRKAT 2in TCT 2-Pack9.6/10View on Amazon
  4. 4SALI 1in TCT KitBest Three-BladeSALI 1in TCT Kit9.5/10View on Amazon
  5. 5ChgImposs HSS 5pc SetBest HSS SetChgImposs HSS 5pc Set9.5/10View on Amazon

Stainless steel work-hardens the moment a dull edge rubs it, so the wrong hole saw just polishes the spot and burns up. The best hole saw for stainless steel is a carbide-toothed cutter run slow with coolant, in the exact diameter you need. This guide compares five hole saws on what each Amazon listing states: size, cutter type, capacity, count and the warranty each listing publishes.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall EZARC Carbide 1-1/8in: Carbide cutter for stainless to 3/16 inch thick, spring pilot bit and wrench included. Check price on Amazon
  • Best Kit METOTY 33pc TCT Kit: 33-piece TCT set, 1/2 to 4 inch, with center drills and wrenches for stainless metal. Check price on Amazon
  • Best 2-Inch Pick DECKRKAT 2in TCT 2-Pack: 2-pack of 2 inch TCT saws with spring pilot bits, 3/8 inch shank, storage case included. Check price on Amazon
  • Best Three-Blade SALI 1in TCT Kit: 1 inch TCT with three-blade tooth design and titanium-plated pilot bit for hard metal. Check price on Amazon
  • Best HSS Set ChgImposs HSS 5pc Set: 5-piece HSS set, 16 to 30 mm, for stainless, aluminum, plastic and wood on drills. Check price on Amazon

The machines

EZARC Carbide Hole Saw Heavy Duty

EZARC Carbide Hole Saw Heavy Duty

EZARC9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1-1/8 inch carbide hole cutter for stainless steel up to 3/16 inch thick, with a spring-loaded pilot bit and a 500-hole claim.

Pros

  • Carbide teeth with a 500-hole stainless claim
  • Cuts material up to 3/16 inch thick
  • Spring-loaded pilot bit for clean plug ejection
  • Pilot bit, spring and wrench included

Cons

  • Single 1-1/8 inch size only
  • 4.48 oz, light but single-purpose
  • No warranty term in the listing
33PCS (1/2'' to 4'') Hole Saw kit for Metal,TCT

33PCS (1/2'' to 4'') Hole Saw kit for Metal,TCT

METOTY9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 33-piece TCT hole saw kit from 1/2 to 4 inch with titanium-plated center drills and wrenches for stainless and hard metal.

Pros

  • 33 pieces: 24 saws, 6 center drills, 3 wrenches
  • Sizes from 1/2 to 4 inch in one kit
  • TCT carbide tipped teeth for stainless and hard metal
  • Coolant and safety guidance in the listing

Cons

  • Model name reads HJK-30PCS for a 33-piece set
  • No warranty term in the listing
  • Bulkier to store than a single saw
  • Titanium plating is a coating claim, not a measured figure
2-Pack 2" TCT Hole Saws for Hard Metal

2-Pack 2" TCT Hole Saws for Hard Metal

DECKRKAT9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 2-pack of 2 inch TCT hole saws with spring-loaded pilot bits, 3/8 inch shank and a storage case.

Pros

  • Two 2 inch TCT saws, a spare on hand
  • Spring-loaded pilot bits for debris removal
  • 3/8 inch 3-flatted shank for a steady chuck grip
  • Pre-oiled in a plastic storage case

Cons

  • Only the 2 inch size in the set
  • 1 inch cutting length limits deep cuts
  • No warranty term in the listing
SALI 1" (26mm) TCT Hole Saw Kit Tungsten Carbide

SALI 1" (26mm) TCT Hole Saw Kit Tungsten Carbide

SALI9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1 inch TCT hole saw kit with a three-blade tooth design and titanium-plated pilot bit for hard metal.

Pros

  • Three-blade tooth design: outer, middle and inner blades
  • TCT carbide teeth for hard metals
  • Titanium-plated pilot bit
  • 1 inch cutting depth stated

Cons

  • Depth reads 1 inch (60mm), a unit mismatch
  • Single 1 inch size
  • No warranty term in the listing
  • Cannot be used for concrete, tile or stone
ChgImposs 5Pcs 16-30mm 5/8-Inch to 1-3/16 Inch HSS

ChgImposs 5Pcs 16-30mm 5/8-Inch to 1-3/16 Inch HSS

ChgImposs9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-piece HSS hole saw set from 16 to 30 mm for stainless steel, aluminum, plastic and wood.

Pros

  • Five sizes from 16 to 30 mm in one set
  • HSS steel for stainless and thick steel plate
  • Fits hand drills and drill presses
  • Good size range for locks, knobs and panels

Cons

  • HSS, not carbide, so shorter life on stainless
  • No warranty term in the listing
  • Material field reads HHS, a typo for HSS

Other welders and gear to compare

Spec sheet comparison

Model Gear Score Size Cutter Capacity Count Warranty
EZARC Carbide 1-1/8in 9.6/10 1-1/8 in Carbide 3/16 in thick 1 None stated
METOTY 33pc TCT Kit 9.6/10 1/2 to 4 in TCT carbide Not stated 33 None stated
DECKRKAT 2in TCT 2-Pack 9.6/10 2 in TCT 1 in length 2 None stated
SALI 1in TCT Kit 9.5/10 1 in TCT 1 in depth 1 None stated
ChgImposs HSS 5pc Set 9.5/10 16-30 mm HSS Not stated 5 None stated

These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 21 October 2026.

Buying guide: what matters in the best hole saw for stainless steel

Carbide vs HSS

Four picks here are carbide or TCT and one is HSS. Carbide teeth hold an edge far longer on stainless, which work-hardens under a dull cutter. The HSS ChgImposs set works for occasional holes, but for regular stainless work the carbide picks are the better read of these listings.

Size and count

The METOTY kit covers 1/2 to 4 inch in 24 saws, the ChgImposs covers 16 to 30 mm in five, and the other three are single sizes: 1-1/8 inch, 1 inch and 2 inch. Buy the kit if you cut many sizes; buy the single saw if you cut one hole size repeatedly.

Cutting depth and capacity

The EZARC states material up to 3/16 inch thick, the DECKRKAT states a 1 inch cutting length, and the SALI states a 1 inch cutting depth with a mismatched 60mm figure. Check the depth against your stock: a saw that cannot reach through the material is the wrong saw.

Coolant and technique

Two listings here tell you to add coolant during continuous high-speed drilling and to wear goggles and gloves. Stainless needs slow speed, steady feed and coolant; the DECKRKAT listing adds to start slow on the pilot bit and increase speed as the saw bites. Let the teeth cut and keep them cool.

Before You Strike an Arc

  • Match the saw diameter to the hole; the single-size picks cannot be adjusted.
  • Use coolant on stainless and keep the speed low; work-hardening ruins both the hole and the saw.
  • Clamp the workpiece; a grabbing hole saw spins the stock, not the saw.
  • Confirm depth figures on arrival where a listing’s own units disagree.
  • Wear goggles and gloves, as two listings here instruct.

FAQ for welders

What kind of hole saw cuts stainless steel?

Carbide or TCT toothed saws, per these listings. Four of the five picks here are carbide-based; the fifth is HSS for lighter use. Bi-metal saws exist, but the EZARC maker claims about 10 times the life for carbide over bi-metal, as a marketing claim.

Can I use a regular drill for stainless hole saws?

Yes, where the listing says so. The DECKRKAT, METOTY and ChgImposs listings name hand drills and drill presses, and the SALI names bench and magnetic drills. Keep the speed low and the feed steady on stainless.

Do I need cutting oil for stainless steel?

Two listings here say to add coolant during continuous high-speed drilling. Stainless work-hardens fast, so coolant, slow speed and steady pressure are the standard approach these listings describe.

How thick stainless can these saws cut?

The EZARC states up to 3/16 inch thick. The DECKRKAT states a 1 inch cutting length and the SALI a 1 inch cutting depth. The others do not state a thickness; check your stock against the stated figures.

Why did my hole saw stop cutting?

Usually heat and a dulled edge: stainless work-hardens when a dull tooth rubs instead of cuts. The listings here point to coolant, lower speed and sharp carbide teeth as the fix. When a saw stops cutting, replace it rather than forcing it.

Related: best hole saw for metal, tubing notcher vs hole saw jig, tube bender for stainless steel, best sanding disc for stainless steel, best wire brush for stainless steel, best wire wheel for stainless steel, and the metal fab tools hub.

Scoring, line by line

Each saw is scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. None of these listings states a safety certification or a warranty term, so every pick here scores zero on those two criteria; the ranking comes from stated cutter type, stainless fit and value.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
EZARC Carbide 1-1/8in 9.6 29 21 20 n/a 0
METOTY 33pc TCT Kit 9.6 28 20 21 n/a 0
DECKRKAT 2in TCT 2-Pack 9.6 28 20 20 n/a 0
SALI 1in TCT Kit 9.5 27 20 19 n/a 0
ChgImposs HSS 5pc Set 9.5 24 19 20 n/a 0

Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score. Unpowered items with no stated safety features skip the safety line, and their score comes from the 90 points that are left.

More buying guides

Metal Fab Tools ·

Best Band Saw Blade for Stainless Steel (2026)

Band saw blades for stainless steel: three M42 blades, two with 8% cobalt stated, stainless-named picks and general-purpose packs for portable and stationary saws.