Best Hole Saw for Cutting Thick Metal (2026)
Five hole saws for thick metal, from a carbide 7/8 inch cutter to a six-size TCT set, compared on stated cutting thickness, tooth material and sizes.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best for thick metalGSTK TCT 8 Piece9.7/10View on Amazon - 2
Best carbide singleEZARC Carbide 7/8 in9.6/10View on Amazon - 3
Largest single cutEMSTAR 4-1/4 in9.6/10View on Amazon - 4
Best kitKATA 18 Piece Kit9.5/10View on Amazon
A hole in thick steel starts with the right cutter, not a faster drill. A wood-rated hole saw skates across the surface, dulls fast and leaves a ragged hole. This guide compares five picks for the best hole saw for cutting thick metal on what each listing states: cutting thickness, tooth material, sizes and warranty.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best for thick metal GSTK TCT 8 Piece: TCT carbide cutters in six sizes, with the maker stating holes in 3 mm stainless steel, 15 mm iron plate and 15 mm aluminum alloy. Check price on Amazon
- Best carbide single EZARC Carbide 7/8 in: Carbide teeth the maker states cut over 500 holes through stainless steel, cutting material up to 3/16 in thick. Check price on Amazon
- Largest single cut EMSTAR 4-1/4 in: A 4-1/4 inch bi-metal saw with arbor and pilot bit, for metal, wood and plastic. Check price on Amazon
- Best kit KATA 18 Piece Kit: Eleven M42 bi-metal sizes from 3/4 to 2-1/2 inch in a case, for thin metal sheet and home projects. Check price on Amazon
The machines

Hole Saw 8 PCS, Hole Saw for Metal
A TCT carbide set with six sizes and two extra pilot bits, stating holes in 3 mm stainless steel, 15 mm iron plate and 15 mm aluminum alloy.
Pros
- Six TCT carbide sizes from 5/8 to 1-3/4 inch in one set
- Maker states holes in 3 mm stainless steel and 15 mm iron plate
- Two extra pilot center bits and two springs in the box
- Three-edged cutterhead and double circular design for chip removal
Cons
- Largest size is 1-3/4 inch, so no large conduit or vent holes
- Needs coolant when drilling continuously at high speeds, per the maker
- Smallest size is 5/8 inch, so no smaller holes in the set
- No storage case is listed with the set

EZARC Carbide Hole Saw Heavy Duty
A single carbide hole saw in 7/8 inch, with a spring-loaded pilot bit and a stated 500-hole life through stainless steel.
Pros
- Carbide teeth the maker states cut over 500 holes through stainless steel
- Cuts material up to 3/16 in thick, including stainless steel
- Spring-loaded pilot bit for fast drilling and clean plug ejection
- Pilot drill bit, spring and wrench included, no extra accessories to buy
Cons
- One size only, 7/8 inch, so no other hole sizes in the box
- 3/16 in is the stated maximum thickness
- No warranty term is stated
- Stated for metal sheet only, so wood and plastic work is not the stated use

4-1/4" Bi-Metal Hole Saw with Arbor
A heavy duty 4-1/4 inch bi-metal saw with arbor and pilot bit, for metal, wood and plastic.
Pros
- Large 4-1/4 inch cut for conduit, plumbing access and ductwork
- Hardened high-speed steel teeth welded to a flexible alloy steel body
- Deep gullet design for fast chip removal
- Arbor and pilot bit included, ready to use out of the box
Cons
- One size only, 4-1/4 inch
- No cutting thickness is stated, so thick-metal capacity is unverified
- Bi-metal teeth, not carbide, so shorter life than the carbide picks here
- No storage case is listed with the saw

KATA 18 Piece Bi Metal Hole Saw Kit 3/4"-2-1/2"
An 18 piece M42 bi-metal kit with eleven sizes from 3/4 to 2-1/2 inch, mandrels and a case, for thin metal sheet and home projects.
Pros
- Eleven M42 bi-metal sizes from 3/4 to 2-1/2 inch in one kit
- Mandrels, drill bits and hex key in a portable case
- Maker gives metal-cutting tips: low speed, light pressure, cutting oil
- Works with standard electric drill and impact drill
Cons
- Maker states it is not for thick hardened steel
- Stated for thin metal sheet, so thick plate is not the stated use
- Cutting depths beyond about 1-1/2 in are not for this set, per the maker
- Wood, drywall and PVC lead the stated uses, so metal is one of several materials

Bi-Metal Hole Saw 2", 4"
A three-size bi-metal set in 2, 4 and 6 inch, with an arbor joint and two drill bits, aimed at recessed lighting and thin metal.
Pros
- Three useful sizes, 2, 4 and 6 inch, for lighting, vents and wiring
- High-speed steel teeth with a reinforced alloy steel body
- A2 arbor joint and two premium HSS drill bits included
- 6.3 inch dust cover captures debris for overhead work
Cons
- Stated for thin metal sheets, so thick metal is not the stated use
- No warranty term is stated
- Three sizes only, 2, 4 and 6 inch, so no sizes between them
- No cutting thickness is stated, so thick-metal capacity is unverified
Other welders and gear to compare
Hole Saw 1.5-inch/38mm Metal Hole Saw Carbide Tipped HoleCheck price on Amazon
4-1/2 InchCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Sizes | Cutting thickness | Type | Warranty |
|---|---|---|---|---|---|
| GSTK TCT 8 Piece | 9.7/10 | 5/8 to 1-3/4 in | 15 mm iron plate | TCT carbide | Not stated |
| EZARC Carbide 7/8 in | 9.6/10 | 7/8 in | Up to 3/16 in | Carbide | Not stated |
| EMSTAR 4-1/4 in | 9.6/10 | 4-1/4 in | Not stated | Bi-metal | Not stated |
| KATA 18 Piece Kit | 9.5/10 | 3/4 to 2-1/2 in | Thin metal sheet | Bi-metal M42 | Limited warranty |
| METOTY 2-4-6 in | 9.5/10 | 2, 4, 6 in | Thin metal | Bi-metal | Not stated |
Treat the specs as maker ratings pulled straight from the listings; we gathered them on 18 November 2026.
Buying guide: the best hole saw for cutting thick metal
Cutting thickness first
Thickness is the first figure to check for this keyword, and only two listings state one. The EZARC cuts material up to 3/16 in thick. The GSTK maker states holes in 3 mm stainless steel, 15 mm iron plate and 15 mm aluminum alloy. The KATA kit is stated for thin metal sheet and not for thick hardened steel, with cutting depths beyond about 1-1/2 in ruled out by the maker. The EMSTAR and METOTY listings state no cutting thickness, so their thick-metal capacity is unverified.
Carbide teeth vs bi-metal
Carbide teeth hold an edge longer in steel than bi-metal teeth, and the two carbide picks here make that case with stated figures. The EZARC states over 500 holes through stainless steel and up to 10x longer cutting life than standard bi-metal hole saws. The GSTK set uses TCT carbide with a three-edged cutterhead. The EMSTAR, KATA and METOTY saws are bi-metal, with hardened high-speed steel teeth, and the METOTY maker states a 3x longer lifespan. For thick metal, carbide is the stronger starting point; bi-metal suits thinner sheet and mixed materials.
Sizes and sets
Size decides what the saw is for. The GSTK set covers six sizes from 5/8 to 1-3/4 inch. The KATA kit covers eleven sizes from 3/4 to 2-1/2 inch. The METOTY set covers 2, 4 and 6 inch. The EZARC is a single 7/8 inch cutter and the EMSTAR is a single 4-1/4 inch cutter. A set suits a shop that cuts many hole sizes; a single cutter suits one repeated hole size.
Pilot bits, arbors and cooling
A hole saw needs a pilot bit to start true and an arbor to hold it. The EZARC includes a spring-loaded pilot bit, spring and wrench. The GSTK set includes two extra pilot center bits and two springs. The EMSTAR includes an arbor and pilot bit, the KATA kit includes mandrels, drill bits and a hex key, and the METOTY set includes an A2 arbor joint and two HSS drill bits. For cooling, the GSTK maker tells you to add coolant when drilling continuously at high speeds, and the KATA maker tells you to use low drill speed, light pressure and cutting oil on metal.
Use as directed. Wear eye protection, clamp the work and keep guards in place. Add coolant when drilling continuously at high speeds, as one maker directs, and keep cords clear of the work. Never exceed the stated cutting thickness or depth for your saw. See the Safety Disclaimer.
Before You Strike an Arc
- Match the saw to the metal: the EZARC cuts stainless steel, mild steel, iron, copper and brass sheet, and the GSTK set covers stainless steel, iron and aluminum.
- Check the arbor and pilot bit on arrival: the EMSTAR includes an arbor and pilot bit, the KATA kit includes mandrels and drill bits, and the METOTY set includes an A2 arbor joint and two HSS drill bits.
- Have coolant or cutting oil on hand: one maker tells you to add coolant when drilling continuously at high speeds, and another tells you to use cutting oil on metal.
- Check the sizes in the box against the holes you need: the GSTK set has six sizes, the KATA kit has eleven, and the METOTY set has three.
FAQ for welders
Can a bi-metal hole saw cut thick metal?
Bi-metal suits thin metal sheet and mixed materials. The KATA kit is stated for thin metal sheet and the maker states it is not for thick hardened steel. For thicker metal, the carbide picks here are the stronger choice: the EZARC cuts material up to 3/16 in thick, and the GSTK maker states holes in 15 mm iron plate.
What size hole saw do I need for thick metal?
Match the saw to the hole, not to the metal thickness. Sizes here run from 5/8 inch to 6 inch: the GSTK set covers 5/8 to 1-3/4 inch, the KATA kit covers 3/4 to 2-1/2 inch, and the METOTY set covers 2, 4 and 6 inch. Single cutters here are 7/8 inch and 4-1/4 inch.
Do I need coolant when cutting thick metal?
Yes, when drilling continuously at high speeds. The GSTK maker tells you to add coolant in that case, and the KATA maker tells you to use low drill speed, light pressure and cutting oil on metal. Let the teeth cut gradually and keep the pilot bit aligned, as the KATA maker advises.
Can I use a hole saw in a standard drill?
Yes. The KATA kit works with a standard electric drill and an impact drill, per the maker. The METOTY set works with standard 1/4 inch hex shank drills. Mark the center point before you start, as the KATA maker advises.
How many holes can a carbide hole saw cut?
The EZARC maker states its carbide teeth cut over 500 holes through stainless steel, with up to 10x longer cutting life than standard bi-metal hole saws. The METOTY maker states a 3x longer lifespan for its bi-metal set. The count depends on the metal and the cooling, so treat the stated figures as the maker’s claim, not a promise.
Related: best step drill bit for thick metal, hole saw vs knockout punch, best drill bit set for hard steel, and the metal cutting saw types guide.
Scoring, line by line
Each saw is scored on performance, build, value, safety listing and warranty, with the weights published on the How We Pick page. No listing here states a safety certification or a warranty term, so every saw here scores zero on safety and warranty; the ranking comes from performance, build and value.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| GSTK TCT 8 Piece | 9.7 | 32 | 21 | 22 | n/a | 0 |
| EZARC Carbide 7/8 in | 9.6 | 30 | 22 | 20 | n/a | 0 |
| EMSTAR 4-1/4 in | 9.6 | 28 | 20 | 20 | n/a | 0 |
| KATA 18 Piece Kit | 9.5 | 26 | 20 | 21 | n/a | 0 |
| METOTY 2-4-6 in | 9.5 | 24 | 20 | 19 | n/a | 0 |
Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score. Safety points apply to gear that runs on power or lists safety features. Without either, we score out of 90 instead of 100.




