Sheet Metal Gauge to Thickness Chart
Sheet metal gauge is a number, not a measurement, and the same number means a different thickness in steel, stainless steel and aluminum. Pick the material and the gauge to get inches and millimeters, or type a thickness to find the nearest gauge.
Gauge and thickness converter
Steel uses the Manufacturers' Standard Gauge, stainless steel the U.S. Standard Gauge and aluminum the Brown & Sharpe (AWG) gauge. Mills roll to a tolerance, so measure the sheet with calipers before you set the machine.
Sheet metal gauge chart
Thickness in inches and millimeters for each gauge. A lower gauge number is thicker metal.
Swipe the table sideways to see the aluminum columns.
| Gauge | Steel in | Steel mm | Stainless in | Stainless mm | Aluminum in | Aluminum mm |
|---|---|---|---|---|---|---|
| 3 | 0.2391 | 6.07 | - | - | - | - |
| 4 | 0.2242 | 5.69 | - | - | - | - |
| 5 | 0.2092 | 5.31 | - | - | - | - |
| 6 | 0.1943 | 4.94 | - | - | 0.1620 | 4.11 |
| 7 | 0.1793 | 4.55 | 0.1875 | 4.76 | 0.1443 | 3.67 |
| 8 | 0.1644 | 4.18 | 0.1719 | 4.37 | 0.1285 | 3.26 |
| 9 | 0.1495 | 3.80 | 0.1562 | 3.97 | 0.1144 | 2.91 |
| 10 | 0.1345 | 3.42 | 0.1406 | 3.57 | 0.1019 | 2.59 |
| 11 | 0.1196 | 3.04 | 0.1250 | 3.17 | 0.0907 | 2.30 |
| 12 | 0.1046 | 2.66 | 0.1094 | 2.78 | 0.0808 | 2.05 |
| 13 | 0.0897 | 2.28 | 0.0937 | 2.38 | 0.0720 | 1.83 |
| 14 | 0.0747 | 1.90 | 0.0781 | 1.98 | 0.0641 | 1.63 |
| 15 | 0.0673 | 1.71 | 0.0703 | 1.79 | 0.0571 | 1.45 |
| 16 | 0.0598 | 1.52 | 0.0625 | 1.59 | 0.0508 | 1.29 |
| 17 | 0.0538 | 1.37 | 0.0562 | 1.43 | 0.0453 | 1.15 |
| 18 | 0.0478 | 1.21 | 0.0500 | 1.27 | 0.0403 | 1.02 |
| 19 | 0.0418 | 1.06 | 0.0437 | 1.11 | 0.0359 | 0.91 |
| 20 | 0.0359 | 0.91 | 0.0375 | 0.95 | 0.0320 | 0.81 |
| 21 | 0.0329 | 0.84 | 0.0344 | 0.87 | 0.0285 | 0.72 |
| 22 | 0.0299 | 0.76 | 0.0312 | 0.79 | 0.0253 | 0.64 |
| 23 | 0.0269 | 0.68 | 0.0281 | 0.71 | 0.0226 | 0.57 |
| 24 | 0.0239 | 0.61 | 0.0250 | 0.64 | 0.0201 | 0.51 |
| 25 | 0.0209 | 0.53 | 0.0219 | 0.56 | 0.0179 | 0.45 |
| 26 | 0.0179 | 0.45 | 0.0187 | 0.47 | 0.0159 | 0.40 |
| 27 | 0.0164 | 0.42 | 0.0172 | 0.44 | 0.0142 | 0.36 |
| 28 | 0.0149 | 0.38 | 0.0156 | 0.40 | 0.0126 | 0.32 |
| 29 | 0.0135 | 0.34 | - | - | - | - |
| 30 | 0.0120 | 0.30 | - | - | - | - |
Why one gauge number has three thicknesses
- Carbon steel follows the Manufacturers’ Standard Gauge for sheet steel. 16 gauge is 0.0598 in (1.52 mm).
- Stainless steel follows the U.S. Standard Gauge. 16 gauge is 0.0625 in (1.59 mm).
- Aluminum follows the Brown & Sharpe gauge, the same series as American Wire Gauge (AWG). 16 gauge is 0.0508 in (1.29 mm).
Galvanized steel is listed a little thicker than bare steel of the same gauge because of the zinc coating, so check the supplier’s sheet for coated stock.
Using the chart at the welder
Machine setting charts are written in thickness, so convert the gauge first and then read the chart on your welder for that thickness. Sheet is rolled to a tolerance and can be a few thousandths either side of the nominal figure, so measure with calipers when the setting is close to a limit.
