Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Step Drill Bit for Sheet Metal (2026): 4 Compared

Four step drill bit sets for sheet metal compared on sizes, range, coating, shank and material, scored for clean holes in thin stock.

Best Step Drill Bit for Sheet Metal (2026): 4 Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1COMOWARE M2 5pcTop PickCOMOWARE M2 5pc9.5/10View on Amazon
  2. 2ZELCAN 5pc 50-sizeRange PickZELCAN 5pc 50-size9.5/10View on Amazon
  3. 3NEIKO 10181A 3pcSplit Point PickNEIKO 10181A 3pc9.5/10View on Amazon
  4. 4IRONANT 5pc 50-sizeCase PickIRONANT 5pc 50-size9.4/10View on Amazon

Drilling sheet metal with a twist bit grabs, tears and leaves a ragged hole. A step drill bit cuts clean, round holes in thin stock one diameter at a time, with no pilot hole and no tearing. The best step drill bit for sheet metal here is an M2 cobalt set with an AlTiN coating rated 67HRC, claiming up to 3 times faster drilling than conventional step bits. This guide compares four step drill bit sets on sizes, range, coating, shank and material.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Top Pick COMOWARE M2 5pc: M2 cobalt step bits, AlTiN 67HRC, 3x faster drilling claimed, 3/8 in shank. Check price on Amazon
  • Range Pick ZELCAN 5pc 50-size: 5-piece 50-size set, 1/8 to 1-3/8 in, titanium HSS, 1/4 in hex shank. Check price on Amazon
  • Split Point Pick NEIKO 10181A 3pc: 3-piece 31-size set, split point tip, impact-ready 1/4 in hex shank. Check price on Amazon
  • Case Pick IRONANT 5pc 50-size: 5-piece 50-size set, 118-degree split point, aluminum case. Check price on Amazon

The machines

M2 Step Drill Bit Set, 1/8~1-3/8" 5Pcs 4 Spiral

M2 Step Drill Bit Set, 1/8~1-3/8" 5Pcs 4 Spiral

COMOWARE9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-piece M2 cobalt step bit set with AlTiN 67HRC coating, 3/8-inch shank and 1/8 to 1-3/8 inch range.

Pros

  • M2 cobalt HSS, AlTiN 67HRC
  • Up to 3x faster drilling claimed
  • 3/8 in shank for higher torque
  • Stated for stainless and mild steel

Cons

  • No warranty term stated
  • No safety certification stated
  • Mild steel limited to 1/8 in thick
  • Stainless limited to 1mm thick
ZELCAN 5PCS Titanium HSS Step Drill Bit Set

ZELCAN 5PCS Titanium HSS Step Drill Bit Set

ZELCAN9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-piece titanium HSS step bit set with 50 sizes from 1/8 to 1-3/8 inches and a 1/4-inch hex shank.

Pros

  • 50 sizes, 1/8 to 1-3/8 in
  • Titanium-coated HSS, 4-flute spiral
  • 1/4 in hex shank, quick release
  • Storage case with size markings

Cons

  • No warranty term stated
  • No safety certification stated
  • Standard HSS, not cobalt
  • No stated speed figure
NEIKO 10181A Step Drill Bit Set, 3 Piece

NEIKO 10181A Step Drill Bit Set, 3 Piece

NEIKO9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3-piece titanium nitride step bit set with 31 sizes, split point tip and impact-ready 1/4-inch hex shank.

Pros

  • 31 sizes across 3 bits
  • Split point tip prevents walking
  • 2-flute spiral deburrs as it cuts
  • Impact-ready 1/4 in hex shank

Cons

  • Tops out at 7/8 in
  • No warranty term stated
  • No safety certification stated
  • Standard HSS, not cobalt
5-Piece HSS Step Drill Bit Set for Metal

5-Piece HSS Step Drill Bit Set for Metal

IRONANT9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-piece TiAlN step bit set with 50 sizes, 118-degree split point and an aluminum case.

Pros

  • 50 sizes across 5 bits
  • TiAlN coated HSS
  • 118-degree split point self-centers
  • Aluminum carrying case

Cons

  • Not for stainless steel
  • Not for wood
  • No warranty term stated
  • No safety certification stated

Other welders and gear to compare

Spec sheet comparison

Bit set Pieces Sizes Range Shank Coating
COMOWARE M2 5pc 5 Not stated 1/8 to 1-3/8 in 3/8 in hex AlTiN, 67HRC
ZELCAN 5pc 50-size 5 50 1/8 to 1-3/8 in 1/4 in hex Titanium
NEIKO 10181A 3pc 3 31 1/8 to 7/8 in 1/4 in hex Titanium nitride
IRONANT 5pc 50-size 5 50 Not stated 3-Flat TiAlN

Treat the specs as maker ratings pulled straight from the listings; we gathered them on 20 October 2026.

How to choose the best step drill bit for sheet metal

Size range

The widest range here is 1/8 to 1-3/8 inches on the ZELCAN 5-piece set and on the COMOWARE title, though the COMOWARE bullets state 1/4 to 1-3/8 inches. The NEIKO 3-piece tops out at 7/8 inch across 31 sizes. Match the range to the largest hole you drill; the IRONANT states 50 sizes without a stated range.

Coating and material

The COMOWARE is the only M2 cobalt set here, with an AlTiN coating the listing rates at 67HRC and a claim of up to 3 times faster drilling. The others are titanium-coated HSS: the ZELCAN 5-piece and NEIKO with titanium or titanium nitride, the IRONANT with TiAlN. Harder coatings suit stainless. The ZELCAN 5-piece cuts steel, aluminum and copper, the NEIKO drills stainless steel and other sheet metal, and the IRONANT covers plastic, aluminum, iron and sheet metal.

Shank

The COMOWARE upgrades to a 3/8-inch shank for higher torque, while the ZELCAN 5-piece and NEIKO use 1/4-inch hex shanks; the NEIKO states its shank is impact-ready. The IRONANT uses a 3-flat shank.

Stainless versus mild steel

Not every set handles stainless. The COMOWARE is stated for stainless steel, mild steel and aluminum. The IRONANT is not recommended for stainless steel. The ZELCAN 5-piece and NEIKO state stainless among their materials.

Before You Strike an Arc

  • Clamp thin sheet before drilling; step bits grab less than twist bits but the work can still spin.
  • Use cutting oil on steel and start slow, as the COMOWARE listing advises.
  • Wear eye protection; hot chips fly when stepping up diameters.
  • Deburr both sides of the hole after drilling.

FAQ for welders

What is a step drill bit for?

Drilling clean, round holes in thin sheet metal without a pilot hole. Each step cuts one diameter, so one bit covers many hole sizes.

How many sizes do these cover?

50 sizes on the ZELCAN 5-piece and IRONANT sets, 31 on the NEIKO 3-piece. The COMOWARE title gives a 1/8 to 1-3/8 inch range without a size count.

Can they drill stainless steel?

The COMOWARE states stainless steel among its materials, with usage notes for stainless up to 1mm thick. The IRONANT is not recommended for stainless.

What shank do I need?

Match your chuck: 1/4-inch hex on the ZELCAN 5-piece and NEIKO, 3/8-inch on the COMOWARE, 3-flat on the IRONANT. The NEIKO states impact-ready compatibility.

Do I need cutting oil?

The COMOWARE listing says to always apply cutting oil or coolant during continuous operation and to start at a slower speed.

Related: the best hole saw for metal, the best sheet metal nibbler, the best hand seamer for sheet metal, the sheet metal shears vs tin snips and the metal fab tools hub.

Scoring, line by line

Each set is scored on performance, build, value, safety and warranty. No listing here states a safety certification or a warranty term, so safety and warranty score zero across the board; the ranking comes from material, coating, size range and shank.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
COMOWARE M2 5pc 9.5 32 21 21 0 0
ZELCAN 5pc 50-size 9.5 30 21 20 0 0
NEIKO 10181A 3pc 9.5 29 21 20 0 0
IRONANT 5pc 50-size 9.4 28 20 20 0 0

Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score.

More buying guides