Sheet Metal Shears vs Tin Snips: Which One Should You Buy?
Sheet metal shears vs tin snips: a cordless shear, two aviation snips and a hard-material snip set compared on cut capacity and power.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Cordless Sheet Cutter Compatible with DeWalt 20V9.4/10View on Amazon - 2
MIDWEST Special Hardness Aviation Snips9.4/10View on Amazon - 3
HURRICANE 10 Inch Aviation Tin Snips9.3/10View on Amazon - 4
Amazon Basics Straight Cut Aviation Tin Snips9.3/10View on Amazon
Verdict. Pick the cordless shears side for powered cutting: the YEARTOP is the only listing with a motor, cutting 20-gauge stainless and 18-gauge sheet metal off a DeWalt 20V battery. Pick tin snips for hand control and tight curves: the Amazon Basics and HURRICANE are both straight-cut aviation snips with safety latches. Pick the MIDWEST set for hard materials: its special-hardness blades are stated for stainless steel, inconel and titanium.
Sheet metal shears vs tin snips is a power and control question. The shears side in these listings means a powered cutter and a hard-material snip set; the tin snips side means two manual aviation snips. This guide compares all four as the listings describe them.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
The four tools

Cordless Sheet Cutter Compatible with DeWalt 20V
A cordless 20V sheet cutter with brushless motor, 360-degree pivoting head and 2-year warranty.
Pros
- 2300RPM brushless motor, up to 800W
- Cuts 20ga stainless, 18ga sheet
- 360-degree pivoting head
- Safety lock with forward/reverse
Cons
- Battery not included
- Not for wave-shaped sheets
- Manual head adjustment
- Heavier than hand snips

MIDWEST Special Hardness Aviation Snips
A USA-made left and right offset snip set with special-hardness blades for stainless, inconel and titanium.
Pros
- Stated for stainless, inconel, titanium
- Left and right offset pair
- 20% less effort stated
- Made in USA
Cons
- No warranty stated
- No safety latch stated
- No stainless gauge figure stated
- Set only, no single snip

HURRICANE 10 Inch Aviation Tin Snips
A 10-inch Cr-Mo aviation snip with dual-pivot leverage, stated to cut with up to 40% less force.
Pros
- Up to 40% less cutting force stated
- 20ga CRS, 22ga stainless capacity
- Cr-Mo hardened blades
- Locking latch for storage
Cons
- No warranty stated
- Not for hardened steel or tubes
- Straight cut only
- Heavier than the Amazon Basics snip

Amazon Basics Straight Cut Aviation Tin Snips
A straight-cut aviation snip for 18ga steel and 22ga stainless with a safety latch and one-year warranty.
Pros
- Cuts 18ga CRS, 22ga stainless
- Safety latch with auto release
- Chrome vanadium steel, high-frequency heat treated
- Rubberized 2-color handle
Cons
- Straight cut only
- No hard-metal rating
- Single snip, no left/right pair
- No left/right pair option
Other welders and gear to compare
Sheet Metal Cutter for DrillCheck price on Amazon
VEVOR Sheet Metal BrakeCheck price on Amazon
WEN Metal ShearCheck price on Amazon
KAKA INDUSTRIAL Metal BrakeCheck price on Amazon
Sheet metal shears vs tin snips side by side
| Model | Verdict | Power | Cut capacity | Weight | Warranty |
|---|---|---|---|---|---|
| YEARTOP Cordless Sheet Cutter | Power pick | Cordless 20V (battery not incl.) | 20ga stainless, 18ga sheet | 3.34 lb | 2 Year Manufacturer |
| Amazon Basics Straight Cut Aviation Tin Snips | Value snip | Manual | 18ga CRS, 22ga stainless | 12.8 oz | 1-year limited |
| HURRICANE 10 Inch Aviation Tin Snips | Comfort snip | Manual | 20ga CRS, 22ga stainless | 0.46 kg | Not stated |
| MIDWEST Special Hardness Offset Snips 2-Pc | Hard-material snips | Manual | 18ga CRS | 1.9 lb | Not stated |
20 October 2026
Power: the one motor here
Only the YEARTOP has a motor: a 2300RPM brushless unit stated at up to 800W of power with a maximum torque of 221 Ft-Lbs. It is a bare tool only, compatible with DeWalt 20V Max batteries (battery not included). The other three are manual: the MIDWEST 2-piece set, the Amazon Basics straight-cut snip and the HURRICANE 10-inch snip. The listing warns the YEARTOP is not suitable for wave-shaped metal sheets, where blade jams can occur.
Cut capacity: what each listing states
The YEARTOP states up to 20-gauge stainless steel and 18-gauge sheet metal. The Amazon Basics states up to 18 gauge (1.2 mm) cold-rolled steel and 22 gauge (0.8 mm) stainless steel. The HURRICANE states 20-gauge cold rolled steel and 22-gauge stainless steel, and warns it is not for hard metal wires, hardened steel, tubes or mesh. The MIDWEST states 18-gauge cold-rolled steel cut from beginning of blade to tip with 20% less effort, plus extremely hard materials such as stainless steel, inconel and titanium. Capacity alone does not settle it: the listings state different gauges for different materials.
Blades and grips
The MIDWEST blades are hot drop-forged molybdenum alloy steel, austemper heat-treated, with Kush’N-Power rubber grips, made in the USA. The Amazon Basics uses chrome vanadium steel with a high-frequency heat treatment and a serrated-edge blade, with a 2-colored rubberized handle. The HURRICANE uses chrome molybdenum steel blades with a serrated jaw and soft rubberized handles. The YEARTOP head is carbon steel with a 360-degree pivoting head, adjusted manually with the included wrench for straight, curved or angled cuts.
Warranties and safety latches
The YEARTOP states a 2-year manufacturer warranty and a safety lock with forward and reverse functions. The Amazon Basics names a limited one-year warranty; its latch locks the tool shut with a one-handed auto release. The HURRICANE has a secure locking latch for storage but states no warranty. The MIDWEST states no warranty and no latch. Keep the proof-of-purchase logic in mind: the YEARTOP and the Amazon Basics both put concrete warranty terms in writing, while the HURRICANE and MIDWEST state none.
Weights and dimensions
The weights split by power. The YEARTOP cordless shear is 3.34 lb at 10 by 7 by 2.9 inches, the heaviest here and the only powered tool. The MIDWEST 2-piece set is 1.9 lb. The hand snips are lighter: the Amazon Basics is 12.8 ounces at 9.84 by 2.91 inches, and the HURRICANE is 0.46 kg at 10 by 3 inches. For overhead or all-day cutting, the lighter hand snips win on fatigue; for powered cutting, the YEARTOP’s weight is the price of the motor.
Choose sheet metal shears if
You want powered cutting: the YEARTOP is the only motorized listing, and it runs off DeWalt 20V batteries you may already own. You cut hard materials: the MIDWEST special-hardness blades are stated for stainless, inconel and titanium. You make long straight cuts: the MIDWEST offset models are stated as best for long cuts and trim cuts.
Choose tin snips if
You want hand control for curves: both the Amazon Basics and HURRICANE are straight-cut aviation snips for detailed work. You want the lighter tool: the Amazon Basics is 12.8 ounces and the HURRICANE is 0.46 kg. You want a latch for safe storage: the Amazon Basics and HURRICANE both have one, the YEARTOP has a safety lock, and the MIDWEST states none.
FAQ for welders
Can tin snips cut stainless steel?
The Amazon Basics states up to 22 gauge (0.8 mm) stainless steel and the HURRICANE states 22-gauge stainless steel. The MIDWEST is stated for stainless steel, inconel and titanium with its special-hardness blades. Match the gauge to the listing.
Do I need the DeWalt battery for the YEARTOP?
Yes: the listing states it is a bare tool only, compatible with DeWalt 20V Max batteries, battery not included. Use a fully charged high-capacity battery for the stated performance.
Left cut, right cut or straight cut?
The MIDWEST set includes left and right offset snips for straight cuts and tight curving left and right cuts. The Amazon Basics and HURRICANE are straight-cut snips, stated for clean straight cuts and wide curves.
Which is safer to store?
The Amazon Basics latch locks the tool shut when not in use, the HURRICANE has a secure locking latch, and the YEARTOP has a safety lock. The MIDWEST states no latch.
Related: the best sheet metal shears, the metal shear vs metal nibbler and the best sheet metal shears for aluminum.
Scoring, line by line
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| YEARTOP Cordless Sheet Cutter | 9.4 | 27 | 19 | 18 | 0 | 3 |
| MIDWEST Special Hardness Offset Snips 2-Pc | 9.4 | 28 | 19 | 19 | 0 | 0 |
| HURRICANE 10 Inch Aviation Tin Snips | 9.3 | 26 | 19 | 18 | 0 | 0 |
| Amazon Basics Straight Cut Aviation Tin Snips | 9.3 | 24 | 18 | 19 | 0 | 0 |
Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score.




