Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Tin Snips for Sheet Metal (2026): 5 Picks Compared

Five aviation tin snips for sheet metal, compared by cut direction, gauge capacity, blade steel, handle, latch and spring.

Best Tin Snips for Sheet Metal (2026): 5 Picks Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1HURRICANE 3-Pc SetBest OverallHURRICANE 3-Pc Set9.7/10View on Amazon
  2. 2HOUSERAN 12-InchLongest BladesHOUSERAN 12-Inch9.6/10View on Amazon
  3. 3warmtree 10-InchAlso Greatwarmtree 10-Inch9.6/10View on Amazon

A patch panel waits on the bench, and the cut line runs across thin sheet metal that a grinder would chew up. The best tin snips for sheet metal follow that line by hand, with the right cut direction, a blade that holds its edge, and a latch that keeps the jaws shut in the toolbox. This guide compares the snips by cut direction, gauge capacity, blade steel and handle, with the HURRICANE set leading because it covers straight, left and right cuts.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read the affiliate disclosure.

Quick picks

  • Best Overall HURRICANE 3-Pc Set: Three snips for straight, left and right cuts, with Cr-V serrated blades and a safety latch on each. Check price on Amazon
  • Longest Blades HOUSERAN 12-Inch: 12-inch straight blades with a double lever, etched scale and a metal safety lock. Check price on Amazon
  • Also Great warmtree 10-Inch: Blades rated 58-62HRC with serrated edges and Tyregrip rubberized handles. Check price on Amazon

The machines

HURRICANE 3 pc Aviation Tin Snips Set

HURRICANE 3 pc Aviation Tin Snips Set

HURRICANE9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3-piece aviation tin snips set with straight, left and right cut snips, Cr-V serrated blades, TyreGrip handles and a safety latch on each snip.

Pros

  • Three snips cover straight, left and right cuts
  • Cr-V serrated blades grip the metal to prevent slipping
  • Safety latch and self-opening spring on each snip
  • Non-slip rubber TyreGrip handles reduce hand fatigue

Cons

  • Cuts up to 20-gauge cold rolled steel, below the 18-gauge picks
  • No warranty term is stated
  • Not for hardened steel, rods or wire mesh
  • Not recommended for cardboard, fabric or fiberglass
HOUSERAN 12 Inch Aviation Snips

HOUSERAN 12 Inch Aviation Snips

HOUSERAN9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 12-inch aviation snips with extra-long straight blades, a double lever, etched scale markings and a metal safety lock.

Pros

  • 12-inch straight blades for long cuts and wide curves
  • Double-lever design boosts cutting force
  • Etched scale improves accuracy
  • Metal safety lock and TPR non-slip grip

Cons

  • Title says CR-MO, bullets say drop-forged CR-V steel
  • No warranty term is stated
  • No stated gauge capacity for steel
  • No stated blade hardness rating
10 Inch Aviation Tin Snips

10 Inch Aviation Tin Snips

warmtree9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 10-inch straight-cut aviation snips with Cr-V blades rated 58-62HRC, serrated edges and Tyregrip rubberized handles.

Pros

  • Blades rated 58-62HRC for hardness
  • Cuts 18-gauge cold rolled steel and 22-gauge stainless steel
  • Serrated edges grip material for accurate, burr-free cuts
  • Spring-assisted mechanism for fast one-handed operation

Cons

  • No warranty term is stated
  • No stated weight
  • Protective gloves not included
  • 30% faster cutting speed is the maker's claim, with no stated baseline
WORKPRO 8 Inch Aviation Tin Snips

WORKPRO 8 Inch Aviation Tin Snips

WORKPRO9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An 8-inch straight-cut aviation snips with Cr-V serrated teeth, a safety lock, self-locking nuts and a dual-leverage design.

Pros

  • Cuts 18-gauge cold rolled steel and 22-gauge stainless steel
  • Dual-leverage design for large shearing force with less effort
  • Safety lock and self-locking nuts prevent accidental detachment
  • Serrated cutting edge prevents materials from slipping

Cons

  • No warranty term is stated
  • No stated weight
  • 8-inch size, shorter than the 10-inch and 12-inch picks
  • No stated case or sheath for storage
wikmonx 10" Aviation Tin Snips,Straight Cut

wikmonx 10" Aviation Tin Snips,Straight Cut

wikmonx9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 10-inch straight-cut aviation snips with forged CR-V serrated blades, a bulldog-style nose and a textured rubberized grip.

Pros

  • Cuts 18-gauge cold rolled steel and 22-gauge stainless steel
  • Bulldog-style nose concentrates leverage at the tip
  • Forged CR-V blades, heat-treated, with sandblasted anti-rust finish
  • Spring-assisted latch locks closed in storage

Cons

  • No warranty term is stated
  • No stated weight
  • No stated case or sheath for storage

Other welders and gear to compare

Spec sheet comparison

Model Gear Score Length Cut Cold rolled steel Stainless steel Blades Latch
HURRICANE 3-Pc Set 9.7/10 10 in Straight, left, right 20-gauge 22-gauge Cr-V serrated Safety latch
HOUSERAN 12-Inch 9.6/10 12 in Straight, wide curves Not stated Not stated CR-V steel Metal safety lock
warmtree 10-Inch 9.6/10 10 in Straight, gentle curves 18-gauge 22-gauge Cr-V serrated Locking latch
WORKPRO 8-Inch 9.6/10 8 in Straight 18-gauge 22-gauge Cr-V serrated Safety lock
wikmonx 10-Inch 9.6/10 10 in Straight 18-gauge 22-gauge CR-V serrated Spring latch

All specs here repeat what the maker rates and the listing prints, copied down 1 November 2026.

How the picks were scored

Each snip is scored out of 10 on performance, build, value, safety and warranty, with the weights published in the site scoring guide. Tin snips have no safety certification to state, so every pick here scores zero on safety and warranty. The ranking comes from cut direction, gauge capacity, blade steel and handle.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
HURRICANE 3-Pc Set 9.7 30 22 21 n/a 0
HOUSERAN 12-Inch 9.6 30 21 21 n/a 0
warmtree 10-Inch 9.6 29 21 21 n/a 0
WORKPRO 8-Inch 9.6 29 21 20 n/a 0
wikmonx 10-Inch 9.6 28 20 20 n/a 0

A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number. Unpowered items with no stated safety features skip the safety line, and their score comes from the 90 points that are left.

Buying guide: the best tin snips for sheet metal

Cut direction: straight, left or right

Aviation snips come color coded: yellow cuts straight, red cuts left and green cuts right. The HURRICANE set includes all three, yellow for straight and wide curves, red for tight left turns and green for tight right turns. The HOUSERAN, warmtree, WORKPRO and wikmonx snips are straight-cut snips, and the HOUSERAN and warmtree also handle wide or gentle curves.

Gauge capacity

Gauge capacity is the thickest metal the snips cut, stated separately for cold rolled steel and stainless steel. The WORKPRO, wikmonx and warmtree snips cut up to 18-gauge cold rolled steel and 22-gauge stainless steel. The HURRICANE set cuts up to 20-gauge cold rolled steel and 22-gauge stainless steel. The HOUSERAN listing states no gauge capacity, so check the thickness of the metal you cut before buying.

Blade steel and edge

The HURRICANE, WORKPRO, wikmonx and warmtree snips state chrome vanadium steel blades with serrations that grip the metal. The warmtree blades carry a 58-62HRC hardness rating, the only hardness figure stated here. The wikmonx blades are forged and heat-treated with a sandblasted anti-rust finish, and the HURRICANE blades have a rust-resistant sanded finish. The HOUSERAN title says CR-MO while its bullets say drop-forged CR-V steel.

Handles and latches

A latch keeps the jaws shut in the toolbox, and a spring opens them for the next cut. Every snip here has a latch: the HURRICANE has a manual safety locking latch, the WORKPRO a safety lock, the wikmonx a spring-assisted latch, the warmtree a locking latch and the HOUSERAN a metal safety lock. Handles are rubberized for grip, and the HURRICANE, WORKPRO, wikmonx and HOUSERAN snips have a hanging or suspension hole.

Weight and size

The HURRICANE set weighs 1.0 lb and the HOUSERAN snips weigh 0.97 lb. The WORKPRO, wikmonx and warmtree listings state no weight. Lengths run 8 inches on the WORKPRO, 10 inches on the HURRICANE, wikmonx and warmtree, and 12 inches on the HOUSERAN.

Wear gloves and eye protection. Sheet metal edges cut skin, and snips throw sharp slivers. The wikmonx listing says to wear gloves and eye protection when cutting sheet metal, and the warmtree listing says to wear protective gloves. Keep the latch closed in storage, and keep fingers clear of the blades while cutting.

Before You Strike an Arc

  • Check the 10-inch tool dimensions before use, since hand sizes vary.
  • Match the snip to the cut: yellow for straight, red for left and green for right in the HURRICANE set.
  • Check the gauge of the metal against the stated capacity: 18-gauge cold rolled steel on the WORKPRO, wikmonx and warmtree snips, 20-gauge on the HURRICANE set.
  • Wear gloves and eye protection before the first cut, and check that the latch closes and the spring opens the jaws.

FAQ for welders

What do the yellow, red and green snips cut?

Yellow cuts straight lines and wide curves, red cuts left curves and green cuts right curves. The HURRICANE set includes all three, so one set follows any cutting line. The other four snips here are straight-cut snips.

What gauge sheet metal can these snips cut?

The WORKPRO, wikmonx and warmtree snips cut up to 18-gauge cold rolled steel and 22-gauge stainless steel. The HURRICANE set cuts up to 20-gauge cold rolled steel and 22-gauge stainless steel. The HOUSERAN listing states no gauge capacity.

Do I need aviation snips or tin snips for sheet metal?

Aviation snips are the snips in this guide, and all five are made for sheet metal, HVAC, gutters and duct work. Pick the cut direction first, then the gauge capacity. A straight-cut snips handles straight lines, while a set with left and right snips follows curves.

Can these snips cut stainless steel?

Yes, to 22-gauge. The HURRICANE set, WORKPRO, wikmonx and warmtree snips all state 22-gauge stainless steel. The HOUSERAN listing states no gauge capacity for stainless steel.

What should I check before the first cut?

Check the gauge of the metal against the stated capacity, and match the snip color to the cut direction. Wear gloves and eye protection, and check that the latch closes and the spring opens the jaws.

Related: the metal fab tools hub, the aviation snips vs tin snips guide, the best cut resistant gloves for sheet metal and the best metal shears for corrugated roofing.

More buying guides