Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Cut Resistant Gloves for Sheet Metal (2026)

Cut resistant gloves for sheet metal work, compared on stated cut level, coating, pack size and warranty, with 4 picks from ANSI A1 to A9.

Best Cut Resistant Gloves for Sheet Metal (2026)
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1LOCCEF Level 5/A4Best OverallLOCCEF Level 5/A49.7/10View on Amazon
  2. 2DULFINE A9Highest cut levelDULFINE A99.7/10View on Amazon
  3. 3Schwer A4 AIR-SKINPrecision fitSchwer A4 AIR-SKIN9.6/10View on Amazon
  4. 4Klein Tools A1Light dutyKlein Tools A19.5/10View on Amazon

Moving a cut sheet across a bench puts the edge against the hand at every lift, turn and stack. A glove for that job needs a cut rating the maker states, a coating that holds on steel, and a fit that still lets fingers find a small edge. This guide compares gloves for the best cut resistant gloves for sheet metal, scored on what each listing states.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall LOCCEF Level 5/A4: A4 and Level 5 cut ratings, a 3-pair pack, and the only stated warranty here. Check price on Amazon
  • Highest cut level DULFINE A9: A9 cut resistance with a foam nitrile coating, sold as a 2-pair pack. Check price on Amazon
  • Precision fit Schwer A4 AIR-SKIN: 18-gauge seamless knit with a sandy nitrile coating and reinforced thumb. Check price on Amazon
  • Light duty Klein Tools A1: A1 cut resistance with a microfoam nitrile dip and touchscreen fingertips. Check price on Amazon

The machines

Level 5/A4 Cut Resistant Work Gloves, Touchscreen

Level 5/A4 Cut Resistant Work Gloves, Touchscreen

LOCCEF9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3-pair pack of cut resistant gloves rated Level 5 and A4, with a nitrile coated palm and touchscreen fingertips, backed by a 1 year manufacturer warranty.

Pros

  • Level 5 and A4 cut ratings in the title
  • 3-pair pack for rotation or spares
  • Nitrile coated palm for grip
  • 1 year manufacturer warranty

Cons

  • No bullets in the listing, only a specification table
  • Gauge not stated in the listing
  • Only one size stated, 9/L
  • Liner blend includes glass fiber and steel
A3/A4/A9 Cut Resistant 2/3/6/12 Pairs Work Gloves

A3/A4/A9 Cut Resistant 2/3/6/12 Pairs Work Gloves

DULFINE9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 2-pair pack of A9 cut resistant gloves with a foam nitrile coating, a seamless knit, and touchscreen fingertips for glass cutting and metalwork.

Pros

  • A9 cut resistance, the highest level here
  • Foam nitrile coating with added grip
  • Seamless knit HPPE liner
  • 2-pair pack

Cons

  • Title spans A3, A4 and A9 while this listing is the A9 green pair
  • No warranty term, only a manufacturer's defects note
  • Not water resistant
  • Gauge not stated in the listing
Schwer A4 AIR-SKIN Cut Resistant Work Gloves

Schwer A4 AIR-SKIN Cut Resistant Work Gloves

Schwer9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An 18-gauge seamless knit glove rated ANSI A4, with a sandy nitrile coating, a reinforced thumb, and touchscreen capability for precision work.

Pros

  • ANSI A4 cut resistance for medium duty work
  • 18-gauge seamless knit for precision work
  • Sandy nitrile coating for grip in humid, dry and oily conditions
  • Reinforced thumb crotch for durability

Cons

  • No warranty term in the listing
  • Medium duty rating, below the A9 pick here
  • Single pair, no spare pair in the pack
  • Pull-on closure with no stated cuff adjustment
Klein Tools 60582 A1 Cut-Resistant Work Gloves

Klein Tools 60582 A1 Cut-Resistant Work Gloves

KLEIN TOOLS9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 2-pair pack of ANSI A1 knit dipped gloves in nylon-spandex, with a microfoam nitrile dip coating and touchscreen capable fingertips.

Pros

  • Microfoam nitrile dip for grip in dry, oily and wet conditions
  • Nylon-spandex knit conforms to hand shape for detailed work
  • Touchscreen capable fingertips
  • Machine washable per the bullets

Cons

  • A1 is a light level of cut resistance, the lowest here
  • Warranty only points to the manufacturer website, with no term
  • X-Large size only in this listing

Other welders and gear to compare

Spec sheet comparison

Model Gear Score Cut level Coating Pack Warranty
LOCCEF Level 5/A4 9.7/10 Level 5/A4 Nitrile coated palm 3 pairs 1 year
DULFINE A9 9.7/10 A9 Foam nitrile coated 2 pairs Not stated
Schwer A4 AIR-SKIN 9.6/10 ANSI A4 Sandy nitrile coated 1 pair Not stated
Klein Tools A1 9.5/10 ANSI A1 Microfoam nitrile dip 2 pairs Not stated

Ratings in this table are the makers’ own claims taken from each product page (29 October 2026).

Buying guide: best cut resistant gloves for sheet metal

Cut level

Cut level is the filter to start with for sheet metal work. The DULFINE pick states A9, the highest level here, while the Schwer and LOCCEF picks state A4 and the Klein pick states A1, a light level. A higher level suits sharper, heavier edges, while a light level suits handling where cuts are a lower risk and dexterity matters more. Match the level to the edge: burred, freshly cut sheet calls for a higher rating than smooth, folded stock.

Coating and grip

Every pick here uses a nitrile coating on the palm, but the coatings differ. The Schwer pick uses a sandy nitrile coating that the listing ties to grip in humid, dry and oily conditions. The Klein pick uses a microfoam nitrile dip coating for grip in dry, oily and wet conditions. The DULFINE pick uses a foam nitrile coating with added grip, and the LOCCEF pick uses a nitrile coated palm. For sheet metal, a coated palm helps the hand hold a flat panel without sliding, and a sandy or foam texture adds grip where oil or moisture is present.

Fit and gauge

Fit decides whether a glove stays on the hand through a shift of handling. The Schwer pick is the only pick here that states a gauge: 18-gauge seamless knit, tied by the listing to precision work. The other picks state seamless knits without a gauge, so gauge cannot be compared across the set. Sizes stated here are Large, X-Large and 9/L, so check the size on the listing for the pair ordered against the hand it will fit, since a loose cuff slides and a tight glove tires the hand.

Pack size and warranty

Pack size changes the value of a pick. The LOCCEF pick comes as a 3-pair pack, the Klein and DULFINE picks come as 2-pair packs, and the Schwer pick is a single pair. A spare pair matters when a glove is cut or soiled mid-job. Warranty is thinner across the set: only the LOCCEF listing states a term, 1 year, while the other listings state no term or point to the manufacturer website. Score warranty only where a term is stated.

Care and replacement

Care instructions differ by listing and are worth checking on arrival. The Schwer and LOCCEF listings state hand wash care, while the Klein bullets state machine washable even though the Klein specification table states hand wash. When a listing disagrees with itself, follow the title and bullets, and check the care label on the pair received. Replace a glove with a cut through the coating or a torn seam before handling sheet again, since a damaged glove no longer offers the protection its rating describes.

Use as directed. Cut resistant gloves reduce the risk of cuts from sheet edges; they do not make sharp metal safe to grab carelessly. Check the coating and seams before each use, and use proper lifting when moving large panels.

Before You Strike an Arc

  • Check the size on the listing for the pair ordered: Large, X-Large and 9/L are the sizes stated here.
  • Check the cut rating on the pair received, especially the DULFINE variant, since its title spans A3, A4 and A9 while this listing is the A9 pair.
  • Check the coating and palm before handling sheet, and confirm the touchscreen fingertips work with the device used on the job.
  • Check the care instructions on arrival, since the Klein listing disagrees with itself on washing.
  • Keep a spare pair from a multi-pair pack ready, so a damaged glove can be swapped without stopping the job.

FAQ for welders

What cut level suits sheet metal handling?

It depends on the edge. The picks here range from A1, a light level, to A9, the highest level here. Freshly cut or burred sheet calls for a higher rating, while smooth stock and light handling suit a lower rating. The Schwer and LOCCEF picks sit in the middle at A4, a medium duty level for significant cutting hazards.

Do cut resistant gloves also protect against punctures?

Some listings claim more than cut resistance. The Schwer listing states protection against cuts, punctures and abrasion, and the DULFINE listing states abrasion resistance, puncture proofing and tear resistance among its features. A cut rating alone does not describe puncture protection, so read the features of the pair bought rather than assuming one rating covers every hazard.

Can these gloves work with a touchscreen?

Yes, on the listings here. The Schwer, Klein, LOCCEF and DULFINE listings all state touchscreen capability or touchscreen fingertips. That lets a wearer answer a device without removing the glove, which keeps the hand covered around sheet edges.

How do I choose between a 2-pair and a 3-pair pack?

Think about rotation. A 3-pair pack, like the LOCCEF pick, gives a spare while one pair is washed or replaced. A 2-pair pack, like the Klein and DULFINE picks, still covers a spare. A single pair, like the Schwer pick, suits a buyer who wants one pair for precision work and will replace it when worn.

How should cut resistant gloves be washed?

Follow the listing for the pair bought. The Schwer and LOCCEF listings state hand wash care. The Klein bullets state machine washable, while the Klein specification table states hand wash, so check the care label on the pair received when the listing disagrees with itself.

Related: best cut resistant gloves, cut resistant gloves vs leather gloves, best welding gloves for fabrication, best sheet metal shears, best hand seamer for sheet metal, and the welding safety gear hub.

Scoring, line by line

Each glove is scored on performance, build, value, safety listing and warranty, with the weights published on the How We Pick page. Safety here follows the stated cut rating: A9 outranks A4, and A4 outranks A1, so the safety scores follow the ratings each listing states. Warranty scores follow only a stated term, which is why only one pick here scores on warranty.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
LOCCEF Level 5/A4 9.7 29 20 22 8 3
DULFINE A9 9.7 33 21 21 10 0
Schwer A4 AIR-SKIN 9.6 30 21 20 8 0
Klein Tools A1 9.5 26 20 20 4 0

The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure.

More buying guides

Welding Safety Gear ·

Cut Resistant Gloves Chart by Cut Level

A cut resistant gloves chart matches the cut level to the hazard: A7 for medium to heavy cut hazards and A1 for light work.