Best Metal Shears for Corrugated Roofing (2026): 4 Picks for Roof Panels
Metal shears for corrugated roofing, compared on gauge capacity, head rotation, power source, and the warranty each listing states.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallMalco TSCM9.6/10View on Amazon - 2
Heaviest GaugeMalco TSHD9.6/10View on Amazon - 3
Corded PickGenesis GES409.4/10View on Amazon - 4
Hand Tool PickKAIHAOWIN KH0229.3/10View on Amazon
Corrugated roof panels ask for long, clean cuts that follow ridges and valleys without buckling the sheet or leaving a ragged edge at the eave. A shear that cannot track a profile forces the cut off line, and a hand tool that tires the wrist turns a full roof into slow work. This guide covers the best metal shears for corrugated roofing, scored from what each listing states about gauge capacity, head movement, power source and warranty.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall Malco TSCM: Corrugated-specific drill attachment with a 360-degree rotating head, 30- to 24-gauge mild steel range, and Limited Lifetime warranty. Check price on Amazon
- Heaviest Gauge Malco TSHD: Stated range covers 18-gauge galvanized steel, 20-gauge stainless, 14-gauge aluminum and .100-inch copper through a rotating head. Check price on Amazon
- Corded Pick Genesis GES40: 4-amp corded shear with 14-gauge capacity, variable speed from 0 to 2,500 SPM, and a stated 2 years warranty. Check price on Amazon
- Hand Tool Pick KAIHAOWIN KH022: Offset hand snips in Cr-V steel with a double-lever design, spring rebound and a lock for trims and general sheet work. Check price on Amazon
The machines

Malco TSCM Corrugated Metal TurboShear Drill
A drill-powered shear built for corrugated and box-profile metal roofing, with a 360-degree rotating head, hardened carbon steel blades, and a stated range of 30- to 24-gauge mild steel.
Pros
- Built for corrugated and box-profile panels, with cross-cuts, lengthwise trims and outlet cuts stated in the listing.
- 360-degree rotating shear head with a clamp collar that positions the head at any angle for clearance over profiles.
- Hardened carbon steel blades in an aluminum-cast head, aimed at clean cuts with less manual shearing effort.
- Limited Lifetime warranty stated in the listing, the strongest warranty term among the picks here.
Cons
- Stated range covers 30- to 24-gauge mild steel only, narrower than the heavier gauges the Malco TSHD states.
- Needs a drill to run, so cutting pace depends on the drill on hand rather than a built-in motor.
- Item weight is stated as 2.4 ounces, a figure that reads light for a shear head and deserves a check on arrival.

Malco TSHD TurboShear Heavy-Duty Drill Attachment
A heavy-duty drill-powered shear with the widest stated material range here, cutting 18-gauge galvanized steel, 20-gauge stainless, 14-gauge aluminum and .100-inch copper through a 360-degree rotating head.
Pros
- Widest stated material range here, from 18-gauge galvanized steel to 20-gauge stainless, 14-gauge aluminum and .100-inch copper.
- 360-degree rotating head locks at any angle to follow corrugated panels, standing seams, spiral duct and ribs.
- Telescoping drill clamp adjusts to cordless and corded drills and impact drivers, with spacers stored on the clamp.
- Hardened carbon steel blades with lateral adjustment install on the job, so blade upkeep does not need a bench visit.
Cons
- Warranty description in the listing gives no concrete term, so it scores zero on warranty here.
- Needs a drill to run, so it adds no motor of its own and depends on the drill on hand.
- Listing mentions layered metal and spiral duct work, which may matter less to a reader cutting roofing only.
- Item weight is stated as 2.4 ounces, matching its sibling listing, which deserves a check on arrival.

Genesis Electric Metal Cutting Shear 4 Amp
A corded electric shear with a 4-amp motor, 14-gauge capacity, a 360-degree swiveling head and variable speed from 0 to 2,500 SPM, suited to bench and ground-level sheet cutting.
Pros
- Built-in 4-amp motor means no drill is needed, with variable speed from 0 to 2,500 SPM for varied sheet work.
- 360-degree swiveling head gives cutting control and convenience on sheet metal, flashing and roofing stock.
- 3-blade cutting system is stated to reduce metal deformation during cuts.
- 2 years warranty stated in the listing, with a hex key included for blade replacement.
Cons
- Corded on 120 V with a 5 ft cord, so reach on a roof is limited compared with drill-powered attachments.
- Listing states no corrugated profile following, so its fit for profiled panels is less direct than the Malco picks.
- Weight is stated as 5.4 lbs, heavier in hand than a drill attachment head during long cutting runs.
- Dimensions of 12 x 2.75 x 8 inches make it a bench-sized tool rather than a pocket-sized trim tool.

10" Tin Snips-KAIHAOWIN Aviation Metal Snip Iron
Offset hand snips in Cr-V steel with a double-lever design, spring rebound and a locking catch, suited to trims and general sheet work rather than long corrugated panel runs.
Pros
- Offset blades hold the hand away from the material, giving better control and a lower chance of contact with cut edges.
- Double-lever design lowers the force needed for each cut, easing hand fatigue during prolonged cutting tasks.
- Built-in spring rebounds the handles for one-hand use, with a non-slip sleeve on the handle for grip.
- Lock buckles after use to guard sharp edges and save space in storage.
Cons
- Listing states no gauge capacity, so its fit for corrugated roofing panels cannot be judged from the listing.
- Listing states no warranty term, so it scores zero on warranty here.
- Hand-powered cutting suits trims and short cuts, not long runs across full roof panels.
- Versatile material list covers cardboard and carpet beside metal sheet, which dilutes its roofing focus.
Other welders and gear to compare
WEN Metal ShearCheck price on Amazon
Sheet Metal Cutter for DrillCheck price on Amazon
VEVOR Sheet Metal BrakeCheck price on Amazon
Eastwood Electric Throatless Shear Variable Speed Metal ShearCheck price on Amazon
KAKA INDUSTRIAL Metal BrakeCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Cutting capacity | Head | Power | Warranty |
|---|---|---|---|---|---|
| Malco TSCM | 9.6/10 | 30- to 24-gauge mild steel | 360-degree rotating head | Drill-powered | Limited Lifetime |
| Malco TSHD | 9.6/10 | 18-gauge galvanized steel | 360-degree rotating head | Drill-powered | Not stated |
| Genesis GES40 | 9.4/10 | 14-gauge | 360-degree swiveling head | 120 V corded | 2 years |
| KAIHAOWIN KH022 | 9.3/10 | Not stated | Offset blades | Hand-powered | Not stated |
Treat the specs as maker ratings pulled straight from the listings.
How the picks were scored
Each pick is scored on performance, build, value, safety listing and warranty, with weights described in plain words here: performance, build and value carry the heaviest weight, safety counts where a listing states a safety listing, and warranty counts where a listing states a concrete term. None of the listings here states a safety listing, so every pick scores zero on that criterion, and the ranking comes from the other four.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Malco TSCM | 9.6 | 29 | 21 | 21 | 0 | 4 |
| Malco TSHD | 9.6 | 32 | 22 | 22 | 0 | 0 |
| Genesis GES40 | 9.4 | 24 | 20 | 20 | 0 | 3 |
| KAIHAOWIN KH022 | 9.3 | 21 | 19 | 20 | 0 | 0 |
Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score.
Buying guide: best metal shears for corrugated roofing
Drill-powered attachments for roof panels
The Malco attachments turn a drill the reader already owns into a shear, which suits roof work because the drill travels to the panel instead of a corded tool waiting on an outlet. The Malco TSCM is built for corrugated and box-profile panels, with a rotating head that lets the shear follow cross-cuts, lengthwise trims and outlet cuts around profiles and ridges. The Malco TSHD adds a wider material range, cutting galvanized steel, stainless, aluminum and copper at the gauges its listing states, plus spiral duct and ribs, which suits a shop that cuts roofing and ductwork with the same attachment. Both Malco attachments use a telescoping drill clamp that adjusts to cordless and corded drills and impact drivers, so the fit depends on the drill on hand rather than a fixed mount.
Gauge capacity and what it means on a roof
Gauge capacity decides whether a shear stays in its stated range on the panels being cut. The Malco TSCM listing states cuts in 30- to 24-gauge mild steel roofing and corrugated panels, a range aimed squarely at roofing sheet. The Malco TSHD listing states 18-gauge galvanized steel, 20-gauge stainless, 14-gauge aluminum and .100-inch copper, a heavier stated range that covers thicker roofing and building panels. The Genesis listing states 14-gauge capacity with a 4-amp motor, which places it beside the TSHD on stated gauge while adding a corded motor. The KAIHAOWIN listing states no gauge capacity at all, so its fit for corrugated panels cannot be judged from the listing, and it reads as a trim and general sheet tool rather than a roofing shear.
Head rotation and clearance over profiles
A corrugated panel is not flat, so the head must turn to keep the blades on the cut line as the profile rises and falls. The Malco TSCM and the Malco TSHD both state a 360-degree rotating shear head, with a clamp collar that locks the head at any angle for clearance around profiles and ridges. The Genesis states a 360-degree swiveling head for cutting control, which gives similar freedom on flat sheet and flashing, though its listing does not claim profile following on corrugated panels. The KAIHAOWIN snips take a different route, with offset blades that hold the hand away from the material and a double-lever design that lowers the force needed for each cut.
Corded power against drill power
Power source shapes where each shear works well. Drill-powered attachments need no outlet on the roof, and the drill already on the truck sets the pace, with wide-opening jaws that run at high and low drill speeds on the TSHD. The Genesis is a corded shear on 120 V with a 5 ft cord, so it suits bench and shop cutting near an outlet, and the cord length limits how far it reaches across a roof. Its variable speed range of 0 to 2,500 SPM lets the cutting pace change with the material, and a 3-blade cutting system is stated to reduce metal deformation. For panels already fixed on a roof, the drill attachments avoid the cord question entirely, while the Genesis suits panels cut on the ground or at the bench before fitting.
Blades, upkeep and stated warranty
Blades decide cut quality over time, and the listings differ in what they promise about upkeep. The Malco TSCM uses hardened carbon steel blades in an aluminum-cast head, and the Malco TSHD uses hardened carbon steel blades with lateral adjustment that lets cut quality be maintained as blades wear, with blades that install on the job when replacement comes due. The Genesis includes a hex key for blade replacement, a small but practical detail for a tool whose blades wear with use. The KAIHAOWIN snips use alloy steel blades with 10.9 high-strength bolts, a spring that rebounds the handles, and a lock that buckles after use to guard sharp edges. On warranty, the Malco TSCM states Limited Lifetime, the Genesis states 2 years, and the other listings state no concrete warranty term, so warranty scores follow only what the listings state.
Use as directed. Keep the area under and around the cut clear, keep cords and hoses away from sharp cut edges, wear eye protection suited to metal cutting, and never exceed the stated gauge capacity of the shear in hand. Cut edges stay sharp after the shear passes, so handle offcuts with care and clear them from walkways and roof surfaces.
Before You Strike an Arc
- Confirm the drill clamp fits the drill on hand, since the Malco attachments rely on a telescoping clamp that adjusts to cordless and corded drills and impact drivers.
- Match the shear to the gauge the listing states, from 30- to 24-gauge mild steel on the Malco TSCM to 18-gauge galvanized steel on the Malco TSHD.
- For the Genesis, confirm a 120 V supply within reach of its 5 ft cord before starting a cut.
- Check blades on arrival, keep the Genesis hex key with the tool for blade replacement, and use the TSHD lateral adjustment as blades wear.
- Check the KAIHAOWIN lock after use, since the lock buckles to guard the edges and save space in storage.
FAQ for welders
Can a drill-powered shear follow corrugated profiles?
Yes, where the listing states it. The Malco TSCM is built for corrugated and box-profile panels, and its 360-degree rotating head lets the shear follow cross-cuts, lengthwise trims and outlet cuts around profiles and ridges. The Malco TSHD states the same 360-degree rotation with a clamp collar that locks the head at any angle for corrugated and ribbed panels.
What gauge capacity should a roofing shear state?
It should state the gauges it cuts in the roofing material being used. The Malco TSCM states 30- to 24-gauge mild steel roofing and corrugated panels, while the Malco TSHD states 18-gauge galvanized steel, which is a heavier stated range. A listing that states no gauge capacity, like the KAIHAOWIN listing, leaves the roofing fit unproven, so treat it as a trim tool rather than a roofing shear.
Is a corded shear practical for roof work?
A corded shear suits panels cut at the bench or on the ground, where an outlet is close. The Genesis runs on 120 V with a 5 ft cord, so its reach is limited on a roof, though its variable speed range of 0 to 2,500 SPM suits varied sheet work. For panels already fixed on a roof, a drill-powered attachment avoids the cord question entirely.
Can hand snips cut corrugated roofing panels?
Hand snips suit trims and short cuts rather than full panel runs. The KAIHAOWIN snips offer offset blades, a double-lever design and a spring rebound that lower hand fatigue, but the listing states no gauge capacity for roofing sheet. For long cuts across corrugated panels, a drill-powered or corded shear with a stated gauge range is the better match.
What warranty terms do these listings state?
The Malco TSCM states Limited Lifetime, and the Genesis states 2 years. The Malco TSHD listing gives a warranty description with no concrete term, and the KAIHAOWIN listing states no warranty term, so both score zero on warranty here. Warranty scores in this guide follow only concrete terms the listings state.
Related: electric metal shears vs hand shears, sheet metal shears vs tin snips, best metal shears for roof flashing, best sheet metal shears, straight vs offset tin snips, left vs right cut aviation snips, metal shear vs metal nibbler, and the metal fab tools hub.




