Best Metal Shears for Roof Flashing (2026)
Five metal shears for roof flashing compared on cut capacity, shear type and warranty: cordless shears, drill attachments and a roofer's bent hand shear.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallDEWALT DCS496B9.6/10View on Amazon - 2
Best Drill AttachmentVLOXO ZBJ019.5/10View on Amazon - 3
Roof SpecialistAJC 091-S10T9.4/10View on Amazon
Flashing day on a roof means long straight cuts in coil stock, tight notches around vents and pipes, and bends that have to sit flat against shingles. The best metal shears for roof flashing are the cutters that keep a straight line without chewing the edge: cordless offset shears, drill-powered shear attachments and the roofer’s bent hand shear. This guide compares five cutters on cut capacity, shear type and the warranty each listing states, so you can match the tool to the flashing job in front of you.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall DEWALT DCS496B: Cordless 20V offset shear for 18 gauge, 360 degree swivel head, 3 year warranty. Check price on Amazon
- Best Drill Attachment VLOXO ZBJ01: Drill attachment rated up to 3 mm, chrome vanadium head, 1 year warranty. Check price on Amazon
- Roof Specialist AJC 091-S10T: 10 in roof bent hand shear for commercial roofers, Teflon coating, hardened blades. Check price on Amazon
The machines

DEWALT 20V MAX Metal Shear, Offset, 18GA
A 20V cordless offset shear rated for 18 gauge, with a 360 degree swivel head and a 3 year limited warranty.
Pros
- Cordless 20V power, ready the moment you climb the ladder
- Offset head cuts circles and spiral duct seams per the listing
- 360 degree tool-free swivel head for tight quarters
- 3 year limited warranty, the longest term here
Cons
- No cut rating beyond 18 gauge in the listing
- Tool only, so it needs a 20V battery you already own
- 4 lb is the heaviest cutter here for overhead work
- No safety standard stated in the listing

VLOXO Professional Metal Shear Drill Attachment
A drill shear attachment with a chrome vanadium steel head rated up to 3 mm, a 360 degree pivoting handle and a 1 year warranty.
Pros
- Highest stated cut rating here: up to 3 mm
- Chrome vanadium steel head for wear and rust resistance
- 360 degree pivoting handle for a comfortable grip angle
- 1 year warranty stated in the listing
Cons
- Heaviest at 1.59 lb among the attachments
- Marketing language, so the 3 mm rating needs the listed head to back it
- No safety standard stated in the listing

Metal Sheet Cutter Drill Attachment
A drill-powered nibbler for up to 21 gauge sheet, with hardened steel gears, an 18-month warranty and an honest statement of its limits.
Pros
- Honest 21 gauge, 0.72 mm, rating with stated limits
- Hardened steel gears rather than the aluminum gears the listing warns about
- 18-month warranty, stated twice in the listing
- At 1.04 lb it has the lowest weight here
Cons
- 21 gauge maximum is the lowest capacity here
- Not for corrugated short wave or thick steel per the listing
- Requires a variable speed drill; not compatible with impact drivers
- No safety standard stated in the listing

DEWALT Metal Shear/Cutter Drill Attachment
A DEWALT drill shear attachment rated for 18 gauge, with a 360 degree pivoting head and a 1/4 in hex shank that fits most drills and impact drivers.
Pros
- Rated for 18 gauge across sheet, duct and flashing materials
- 360 degree swivel head for maneuverability in tight spots
- 1/4 in hex shank works with most 18V to 20V drills and impact drivers
- Light 1.59 lb attachment for ladder and roof work
Cons
- No warranty stated in the listing
- Needs a drill or impact driver you already own
- 1.59 lb attachment plus the drill in hand
- No safety standard stated in the listing

AJC Tools 091-S10T 10" Non-Stick Coated Super Duty
A 10 in roof bent hand shear made for commercial roofers, with a non-stick Teflon coating, hardened blades and an adjustable screw.
Pros
- Made specifically for commercial roofers
- Bent handle keeps knuckles clear of the sheet
- Non-stick Teflon coating for easy clean-up
- Precision machined and hardened blades with adjustable screw
Cons
- No gauge rating stated in the listing
- No warranty stated in the listing
- Hand power only, slower on long straight runs
- Right hand orientation only per the listing
Other welders and gear to compare
WEN Metal ShearCheck price on Amazon
Sheet Metal Cutter for DrillCheck price on Amazon
VEVOR Sheet Metal BrakeCheck price on Amazon
KAKA INDUSTRIAL Metal BrakeCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Cut capacity | Type | Weight | Warranty |
|---|---|---|---|---|---|
| DEWALT DCS496B | 9.6/10 | 18 ga | Cordless offset shear | 4 lb | 3 year limited |
| VLOXO ZBJ01 | 9.5/10 | Up to 3 mm | Drill attachment | 1.59 lb | 1 year |
| Chmingright Nibbler | 9.4/10 | Up to 21 ga (0.72 mm) | Drill nibbler attachment | 1.04 lb | 18-month |
| DEWALT DWASHRIR | 9.4/10 | 18 ga | Drill shear attachment | 1.59 lb | Not stated |
| AJC 091-S10T | 9.4/10 | Not stated | Roof bent hand shear | Not stated | Not stated |
Ratings in this table are the makers’ own claims taken from each product page (19 October 2026).
Buying guide: the best metal shears for roof flashing
Cut capacity in gauge
Flashing stock is thin, and every cutter here is rated for it. The DEWALT shear and shear attachment both list 18 gauge, the VLOXO attachment lists up to 3 mm, and the Chmingright nibbler lists up to 21 gauge, 0.72 mm, with an honest warning that thicker stock may jam it. Match the rating to your coil, not your ambition.
Shear type and the cuts you make
Offset shears like the DEWALT DCS496B keep the tool body clear of the sheet, which helps on long rips. The AJC 091-S10T is a roof bent shear, the hand tool made for roofers, with a bent handle that keeps your knuckles off the metal while you trim flashing on the roof. Drill attachments turn a drill you already own into a shear, good value if the drill is already in the kit.
Cordless versus drill attachment
A cordless shear such as the DCS496B runs on its 20V battery and is ready the moment you climb the ladder. Drill attachments cost less and weigh less, 1.59 lb for the DEWALT attachment and 1.04 lb for the Chmingright, but they tie up your drill and are slower to set up. Note the Chmingright states it is not compatible with impact drivers, while the DEWALT DWASHRIR lists both impact drivers and drills.
Shear or nibbler
A shear cuts with two blades and leaves a thin waste strip; a nibbler punches out small crescents and turns tighter curves. For straight flashing runs the shear is faster and cleaner. For notches around pipes and round vents, the nibbler’s tighter turning pays off. See our metal shear vs metal nibbler comparison for the full breakdown.
Edges and gloves
Every cut edge here is sharp. Gloves and eye protection are standard shop practice when cutting and handling flashing. Trim the sharp nibs off corners before you bed the flashing, and keep a first aid kit where you keep the roofing tools.
Use as directed. Keep the cutting path clear, support the sheet so it does not whip as the cut finishes, and disconnect the drill or remove the battery before changing or adjusting blades. Flashing work happens at height, so keep tools tethered or bagged when you are not cutting.
Before You Strike an Arc
- Charge the 20V battery before the DCS496B goes up the ladder; cordless shears are only useful with a full pack.
- For the drill attachments, check the chuck and the 1/4 in hex shank seat before the first cut, and use a variable speed drill as the Chmingright listing requires.
- Oil the blades lightly and check the adjustable screw on the AJC bent shear before a day of trimming.
- Lay out the flashing runs on the ground first, then cut to length on the roof only for the final fit.
FAQ for welders
Can I use a regular power shear for roof flashing?
Yes, if the gauge rating covers your stock. The cordless and drill-powered shears here list 18 gauge or 3 mm, which handles typical flashing coil. For curved cuts around vents, a nibbler turns tighter than a shear.
What thickness of flashing can these cutters handle?
Per the listings: 18 gauge for both DEWALT cutters, up to 3 mm for the VLOXO attachment, and up to 21 gauge, 0.72 mm, for the Chmingright nibbler. The Chmingright listing warns that thicker stock may jam it. The AJC bent shear lists no gauge rating; as a roofer’s hand shear it is made for flashing stock.
Shear or nibbler for flashing work?
Straight runs go to the shear, which cuts faster and leaves a clean edge. Notches, circles and tight corners go to the nibbler. Many roofers carry both and let the cut decide.
Do drill attachments work with impact drivers?
It depends on the attachment. The DEWALT DWASHRIR lists both 18V to 20V impact drivers and drills, while the Chmingright nibbler explicitly states it is not compatible with impact drivers and needs a variable speed drill. Check the listing before you buy.
How do I get clean edges on flashing cuts?
Support the sheet flat, mark the line clearly and move at a steady pace without forcing the tool. On curves, the 360 degree swivel head on the DEWALT cutters helps you follow the mark. Deburr the edge with a file before installation so the flashing beds flat.
Related: best electric metal nibbler, metal nibbler for drill, best sheet metal nibbler and our metal fab tools hub.
Scoring, line by line
Each cutter is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. None of the listings here state a safety standard such as ANSI or CSA, so every cutter here scores zero on that criterion; the ranking comes from the other four.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| DEWALT DCS496B | 9.6 | 30 | 21 | 20 | 0 | 4 |
| VLOXO ZBJ01 | 9.5 | 27 | 20 | 21 | 0 | 3 |
| Chmingright Nibbler | 9.4 | 23 | 19 | 21 | 0 | 3 |
| DEWALT DWASHRIR | 9.4 | 28 | 20 | 21 | 0 | 0 |
| AJC 091-S10T | 9.4 | 27 | 21 | 20 | 0 | 0 |
The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure.






