Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Step Drill Bit for Stainless Steel (2026): 4 Picks Compared

Four step drill bits for stainless steel, compared on hole sizes, shank, coating, flute and the warranty each listing states.

Best Step Drill Bit for Stainless Steel (2026): 4 Picks Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1FRITZFURT M35 3-PieceBest OverallFRITZFURT M35 3-Piece9.5/10View on Amazon
  2. 2Klein Tools KTSB15Best Single BitKlein Tools KTSB159.4/10View on Amazon
  3. 3BOYOUYS M35 3-PieceMost Hole SizesBOYOUYS M35 3-Piece9.4/10View on Amazon
  4. 4SS SHOVAN M35 3-PieceBest for Thin StainlessSS SHOVAN M35 3-Piece9.4/10View on Amazon

A stainless panel waits on the bench with a hole to punch for a switch, a gland or a conduit fitting, and a twist bit would wander, chatter and leave a ragged edge. A step bit cuts the hole cleanly, widening it ring by ring until the size lands where the fitting needs it, and the best step drill bit for stainless steel is the bit that holds its edge through that cut without grabbing or burning the metal.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall FRITZFURT M35 3-Piece: CBN ground M35, 29 hole sizes, AlTiN coating and a stackable case. Check price on Amazon
  • Best Single Bit Klein Tools KTSB15: Klein AlTiN bit, 7/8 to 1-3/8 inch, 3/8 inch hex shank, 1 year warranty. Check price on Amazon
  • Most Hole Sizes BOYOUYS M35 3-Piece: 30 sizes across 3 M35 bits, four spiral flutes, TiAlN coating. Check price on Amazon
  • Best for Thin Stainless SS SHOVAN M35 3-Piece: M35 with 5% cobalt, TiAlN, 118 degree tip, for stainless under 1 mm. Check price on Amazon

The machines

FRITZFURT 3-Piece M35 Cobalt Step Drill Bit Set

FRITZFURT 3-Piece M35 Cobalt Step Drill Bit Set

FRITZFURT9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3-piece M35 cobalt set with 29 hole sizes from 1/8 to 3/4 inch, CBN ground edges, AlTiN coating and a stackable interlocking case.

Pros

  • CBN ground M35 cobalt steel with about 5% cobalt content
  • 29 hole sizes in 6, 10 and 13 step bits, 1/8 to 3/4 inch
  • 25 to 28 degree spiral flute angle keeps chips moving
  • Stackable interlocking case with a clear lid

Cons

  • No warranty term in the listing
  • Largest hole is 3/4 inch, so bigger holes need another bit
  • No stated sheet thickness limit for stainless steel
  • Three separate bits to store and keep track of
Klein Tools KTSB15 Step Drill Bit, Straight Flute

Klein Tools KTSB15 Step Drill Bit, Straight Flute

KLEIN TOOLS9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A single Klein AlTiN step bit from 7/8 to 1-3/8 inch with a 3/8 inch hex shank, double straight flutes and a 1 year warranty.

Pros

  • 1 year manufacturer warranty, the only stated term here
  • AlTiN coating stated as 10 times the durability of black oxide
  • Thick 3/8 inch hex shank resists rounding in the chuck
  • Laser-etched markings for the primary hole sizes

Cons

  • Starts at 7/8 inch, so small holes need another bit
  • Straight flutes where the other picks here use spiral flutes
  • No case or storage stated in the listing
  • Stated for 16-gauge steel, with no thicker stock stated
Four Spiral Flute M35 Step Drill Bit Set 1/4"-1"

Four Spiral Flute M35 Step Drill Bit Set 1/4"-1"

BOYOUYS9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3-piece M35 set with 30 sizes from 1/8 to 1-1/8 inch, four spiral flutes, TiAlN coating and a 1/4 inch shank.

Pros

  • 30 sizes across 3 bits, the most here
  • Four spiral flutes, stated for faster, smoother cutting
  • TiAlN coating for hardness and wear resistance
  • Largest top size of the 3-piece sets here, 1-1/8 inch

Cons

  • Warranty wording gives no concrete term
  • No case or storage stated in the listing
  • No stated sheet thickness limit for stainless steel
  • Three separate bits to store and keep track of
SS SHOVAN 3PCS M35 Cobalt Step Drill Bit Set

SS SHOVAN 3PCS M35 Cobalt Step Drill Bit Set

ss shovan9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3-piece M35 set from 1/4 to 7/8 inch with 5% cobalt, TiAlN coating, a 118 degree tip and a 1/4 inch hex shank.

Pros

  • M35 with 5% cobalt content, stated in the listing
  • 118 degree X-type opening design for precise holes
  • Spiral flute for smooth drilling and chip removal
  • Ships in a box for storage

Cons

  • No warranty term in the listing
  • Range stops at 7/8 inch, below the Klein and BOYOUYS top sizes
  • Stated for stainless steel under 1 mm, so thicker stock is not covered
  • Three separate bits to store and keep track of

Other welders and gear to compare

Spec sheet comparison

Model Gear Score Hole range Bits and sizes Shank Coating Flute Warranty
FRITZFURT M35 3-Piece 9.5/10 1/8 to 3/4 in 3 bits, 29 sizes 1/4 in hex AlTiN Spiral, 25 to 28 degrees None stated
Klein Tools KTSB15 9.4/10 7/8 to 1-3/8 in 1 bit 3/8 in hex AlTiN Straight, double flute 1 year
BOYOUYS M35 3-Piece 9.4/10 1/8 to 1-1/8 in 3 bits, 30 sizes 1/4 in TiAlN Four spiral flute None stated
SS SHOVAN M35 3-Piece 9.4/10 1/4 to 7/8 in 3 bits 1/4 in hex TiAlN Spiral None stated

Treat the specs as maker ratings pulled straight from the listings; we gathered them on 18 November 2026.

How the picks were scored

Each bit is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on the How We Pick page. Step drill bits carry no electrical safety listing, so every bit here scores zero on that criterion; the ranking comes from the other four.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
FRITZFURT M35 3-Piece 9.5 32 22 21 0 0
Klein Tools KTSB15 9.4 28 21 18 0 2
BOYOUYS M35 3-Piece 9.4 29 21 21 0 0
SS SHOVAN M35 3-Piece 9.4 29 20 21 0 0

Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score.

How to pick the best step drill bit for stainless steel

Material and coating

Three of the four picks state M35 cobalt steel, the cobalt high speed steel the makers state for stainless work. The Klein listing does not state the steel grade, only the AlTiN coating. AlTiN coats the FRITZFURT and Klein bits, while TiAlN coats the BOYOUYS and SS SHOVAN sets. Both coatings are stated to cut friction and resist heat, which matters because stainless builds heat in the cut.

Hole range and steps

The FRITZFURT set covers 1/8 to 3/4 inch in 29 sizes, the BOYOUYS set covers 1/8 to 1-1/8 inch in 30 sizes, and the SS SHOVAN set covers 1/4 to 7/8 inch. The Klein bit covers 7/8 to 1-3/8 inch on its own. Match the range to the holes the job needs: panel knockouts and conduit fittings sit inside the set ranges, while larger holes call for the Klein bit.

Shank and flute

Three picks use a 1/4 inch hex shank that snaps into an impact driver or drill chuck, while the Klein uses a thicker 3/8 inch hex shank. Spiral flutes move chips out of the cut; the FRITZFURT states a 25 to 28 degree spiral angle, and the BOYOUYS uses a four spiral flute design. The Klein uses double straight flutes, which the maker states for chip removal and cleaner cuts.

Stainless thickness

Only the SS SHOVAN listing states a thickness for stainless steel, under 1 mm, and the Klein states 16-gauge steel. The other two sets state stainless steel without a thickness figure. For thin sheet and panels, any pick here fits the stated range. For thicker stock, no listing gives a figure, so check the maker notes before ordering.

Use as directed. Wear eye and face protection, clamp the work before drilling, and keep gloves away from rotating parts. Use cutting oil on stainless steel and keep the speed low to medium with steady pressure, as the FRITZFURT maker advises. Keep the area clear of anything that can burn, and never exceed the stated limits. See the OSHA machine guarding page and the Safety Disclaimer.

Before You Strike an Arc

  • Check the shank fits the drill: 1/4 inch hex on three picks, 3/8 inch hex on the Klein.
  • Have cutting oil on hand for stainless steel; the SS SHOVAN maker advises oil or water spray.
  • Check the step sizes against the fitting before drilling; the FRITZFURT set covers 1/8 to 3/4 inch.
  • Confirm the bits arrived complete: 3 bits in each set, 1 bit for the Klein, and a case with the FRITZFURT set.
  • Clamp the work and wear eye protection before drilling.

FAQ for welders

Can a step drill bit cut stainless steel?

Yes, when the bit is made for it. The three M35 sets here state stainless steel in the title, and the Klein states 16-gauge steel. Use cutting oil and steady pressure at low to medium speed, as the FRITZFURT maker advises.

What is the difference between a spiral flute and a straight flute step bit?

A spiral flute winds around the bit and moves chips out of the cut; the FRITZFURT states a 25 to 28 degree spiral angle. A straight flute runs along the bit; the Klein uses double straight flutes, stated for chip removal and cleaner cuts. Both cut stainless steel when the bit is M35 and the speed stays low.

Can I use a step drill bit in an impact driver?

Yes, when the shank fits. The FRITZFURT and SS SHOVAN bits use a 1/4 inch hex shank that snaps into an impact driver or drill chuck, and the Klein uses a 3/8 inch hex shank. Check the chuck size before ordering.

Do I need cutting oil with a step drill bit for stainless steel?

The makers say yes. The SS SHOVAN maker advises cutting oil or water spray to prevent overheating, and the FRITZFURT maker advises cutting oil with steady pressure at low to medium speed for stainless. Oil keeps the edge cooler and the cut smoother.

How many hole sizes does a step drill bit set cover?

It depends on the set. The FRITZFURT set covers 29 hole sizes and the BOYOUYS set covers 30 sizes, while the SS SHOVAN set lists sizes per bit without a total. The Klein is a single bit covering 7/8 to 1-3/8 inch. Match the set to the hole sizes the job needs.

Related: best step drill bit for thick metal, best cutting oil for drilling metal, best drill bits for drilling stainless steel, HSS vs cobalt drill bit and the drill press safety guide.

More buying guides