Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Drill Bits for Drilling Stainless Steel (2026)

Four M35 cobalt and step bit sets for drilling stainless steel, compared on size range, point design, shank and the claims each listing states.

Best Drill Bits for Drilling Stainless Steel (2026)
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1SEDIANAS M35 Cobalt SetBest OverallSEDIANAS M35 Cobalt Set9.6/10View on Amazon
  2. 2Pro Edge 7-Facet StubbyBest Stubby SetPro Edge 7-Facet Stubby9.6/10View on Amazon
  3. 3DelitonGude 1/4 Inch M35Best Single SizeDelitonGude 1/4 Inch M359.6/10View on Amazon
  4. 4KSEIBI 3-Piece Step BitBest Step BitsKSEIBI 3-Piece Step Bit9.5/10View on Amazon

Stainless steel looks friendly until the drill bit touches it. The bit skates across the surface, the tip dulls, the hole wanders off the mark, and the metal around the hole darkens from heat. A bracket, a hinge, a patch panel, a sink cutout: every one of them needs a clean round hole in metal that resists cutting. This guide covers the best drill bits for drilling stainless steel, four sets the listings describe for exactly that job, compared on what each listing states: material, point design, size range, shank and the claims the maker prints.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall SEDIANAS M35 Cobalt Set: The widest set here, 29 sizes in M35 cobalt steel with a 135 degree split point and an indexed metal box. Check price on Amazon
  • Best Stubby Set Pro Edge 7-Facet Stubby: A short M35 cobalt set with a 7-facet point and a 1/4 inch hex shank for fast changes. Check price on Amazon
  • Best Single Size DelitonGude 1/4 Inch M35: Ten bits of one size, 1/4 inch, in M35 cobalt steel with a 135 degree tip. Check price on Amazon
  • Best Step Bits KSEIBI 3-Piece Step Bit: Three step bits on a 1/4 inch impact shank for cordless drills, with a dual-flute design. Check price on Amazon

The machines

Cobalt Drill Bit Set - 29Pcs M35 HSS Twist Drill

Cobalt Drill Bit Set - 29Pcs M35 HSS Twist Drill

SEDIANAS9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A set of 29 sizes in M35 cobalt steel with a 135 degree split point, in a metal index box with a size index.

Pros

  • M35 cobalt steel with 5% cobalt for heat resistance in hard material
  • 135 degree split point self-centers and resists walk-off
  • 29 sizes in one indexed box cover most stainless steel drilling
  • Fully ground twist clears particles and runs cooler

Cons

  • A wide set takes more storage space than a small set
  • Round straight shank gives no extra grip against slipping in the chuck
  • No hex shank for fast bit changes
  • 29 sizes in one box means sorting to find the size needed
7pcs M35 HSS Cobalt Stubby Drill Bit Set 1/4" Hex

7pcs M35 HSS Cobalt Stubby Drill Bit Set 1/4" Hex

Pro Edge Technology9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A stubby M35 cobalt set with a 7-facet point on a 1/4 inch hex shank, in a storage case.

Pros

  • M35 cobalt steel for stainless steel and cast iron
  • Maker claims the 7-facet point extends tool life by 8-10 times
  • 1/4 inch hex shank changes fast and grips tighter for higher torque
  • Seven popular sizes from 3/32 to 3/8 inch cover common drilling needs

Cons

  • Seven sizes only, so larger holes need another set
  • Short bits cannot reach as deep as a standard length bit
  • Hex shank needs a chuck or driver that accepts a hex shank
  • No warranty term is stated
DelitonGude 1/4inch HSS M35 Cobalt Twist Drill

DelitonGude 1/4inch HSS M35 Cobalt Twist Drill

DelitonGude9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

Ten bits of a single size, 1/4 inch, in M35 cobalt steel with a 135 degree tip for steels, cast iron and stainless steel.

Pros

  • M35 high speed steel with 5% cobalt for hard metal
  • 135 degree tip self-centers and stops the bit walking
  • Full-grinding nitriding for wear resistance and chip removal
  • Ten bits of one size give spares for the size drilled most

Cons

  • One size only, so any other hole needs another bit
  • No storage box or case is stated
  • Not for glass or ceramic materials
  • No stated shank type, so chuck fit is not spelled out
KSEIBI 598240 Industrial Grade Unibit 3-Pieces

KSEIBI 598240 Industrial Grade Unibit 3-Pieces

KSEIBI9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3-piece step bit set in M2 high speed steel with a black oxide coating, on a 1/4 inch impact shank for stainless steel, aluminum and wood.

Pros

  • Step design drills several diameters with one bit
  • 1/4 inch impact shank for a secure fit in cordless drills
  • Maker claims up to 2X faster hole times and up to 4X longer life
  • Dual-flute design with a spiral flute for smooth drilling

Cons

  • M2 steel with black oxide, not M35 cobalt
  • No stated step diameters, so the hole sizes are not spelled out
  • Three bits only, so a worn step means replacing the bit
  • No warranty term is stated

Other welders and gear to compare

Spec sheet comparison

Model Material Sizes Point Shank
SEDIANAS M35 Cobalt Set M35 cobalt, 5% cobalt 29 sizes 135 degree split point Round straight shank
Pro Edge 7-Facet Stubby M35 cobalt Seven sizes, 3/32 to 3/8 inch 7-facet point 1/4 inch hex shank
DelitonGude 1/4 Inch M35 M35 cobalt, 5% cobalt Ten bits, 1/4 inch 135 degree tip Not stated
KSEIBI 3-Piece Step Bit M2 high speed steel, black oxide 3-piece step Dual-flute step 1/4 inch impact shank

All specs here repeat what the maker rates and the listing prints, copied down 15 November 2026.

Buying guide: best drill bits for drilling stainless steel

Cobalt grade

Three sets here state M35 cobalt steel, and two of them state 5% cobalt. M35 is the grade the listings pitch for hard material: the SEDIANAS listing says its M35 steel offers heat resistance and greater hardness than ordinary bits, and the DelitonGude listing makes the same claim for its M35 steel with 5% cobalt. The KSEIBI step set is the odd one out, built from M2 high speed steel with a black oxide coating instead of M35 cobalt.

Point design

The point decides whether the bit starts where you put it. Two listings state a 135 degree point: the SEDIANAS set calls it a 135 degree split point with a round straight shank, and the DelitonGude set calls it a 135 tip with a twist design, and both say the point self-centers and stops the bit walking. The Pro Edge set takes a different route with a 7-facet point the maker says cuts better than a standard twist drill. The KSEIBI step bits use a dual-flute stepped design instead of a single point, so each step cuts its own diameter.

Size range

The SEDIANAS set is the only wide range here, with 29 sizes in one indexed box. The Pro Edge set covers seven popular sizes from 3/32 to 3/8 inch, which the maker says covers the most common drilling needs. The DelitonGude set is ten bits of a single size, 1/4 inch, so it suits a reader who drills that size again and again and wants spares on hand. The KSEIBI set is three step bits, so one bit drills several diameters and replaces a handful of twist bits.

Shank and chuck fit

Two sets state a 1/4 inch shank: the Pro Edge set uses a 1/4 inch hex shank the maker says changes fast and grips tighter for higher torque, and the KSEIBI set uses a 1/4 inch impact shank for cordless drills. The SEDIANAS set uses a round straight shank, which fits a standard chuck and gives no extra grip. Check the shank against the chuck before ordering, and check whether the drill is a standard drill or an impact driver, since the KSEIBI set is built for impact-ready use.

Heat and chip clearing

Stainless steel punishes a bit that rubs instead of cutting, and the listings here talk about heat in plain terms. The SEDIANAS listing says its fully ground twist clears particles faster and cuts friction and heat for cooler drilling. The Pro Edge listing says its 7-facet point improves heat dissipation and chip clearance. The KSEIBI listing claims its dual-flute design gives faster hole times and more holes per battery charge, up to 2X faster and up to 50% more, which is the maker talking about cordless work rather than a promise about stainless steel alone. Keep the bit cutting, clear the chips, and let the bit cool between holes.

Use as directed. Clamp the work before drilling, wear eye protection, and keep gloves away from a spinning bit. Keep guards in place on the drill press or hand drill, and keep the area clear of anything that can catch a hot chip. Never exceed the stated limits of the tool, and follow OSHA machine guarding guidance for rotating equipment.

Before You Strike an Arc

  • Check the shank size against the chuck before the first hole: two sets here use a 1/4 inch shank, and one uses a round straight shank.
  • Count the bits on arrival and check the sizes against the stated count: three listings here give more than one count, so check before ordering.
  • Clamp the work and mark the hole center so the bit starts where you mean it to.
  • Keep the index box or storage case closed between jobs so the sizes stay in order.

FAQ for welders

What drill bit material works for stainless steel?

Three sets here use M35 cobalt steel, and the listings pitch M35 for hard material such as stainless steel and cast iron. The SEDIANAS and DelitonGude listings both state 5% cobalt with heat resistance. The KSEIBI step set uses M2 high speed steel with a black oxide coating instead.

What point angle should a bit for stainless steel have?

Two listings here state a 135 degree point, one as a split point and one as a tip with a twist design, and both say the point self-centers and stops the bit walking. The Pro Edge set uses a 7-facet point instead. A point that starts true matters more than the angle alone, since a wandering bit dulls fast on stainless steel.

Do I need one size or a set?

That depends on the holes you drill. The SEDIANAS set carries 29 sizes, the Pro Edge set covers seven sizes from 3/32 to 3/8 inch, and the DelitonGude set is ten bits of one size, 1/4 inch. If every hole is the same size, a single-size set gives spares; if the sizes vary, a wide set saves a second order.

Can I use these bits in a cordless drill?

The KSEIBI set is built for cordless drills, with a 1/4 inch impact shank and a dual-flute design the maker says gives up to 2X faster hole times and up to 50% more holes per battery charge. The Pro Edge set uses a 1/4 inch hex shank for fast changes. The other two sets use a round straight shank or state no shank type, so check the shank against the drill before ordering.

What should I check when the set arrives?

Count the bits and check the sizes against the stated count, since three listings here give more than one count. Check that the shank fits the chuck, that the point is sharp and centered, and that the storage box or case holds the sizes in order.

Related: best drill bit set for metal, best twist drill bit set, best countersink bit cobalt, best cutting fluid for stainless steel, best step drill bit for auto body, best hole saw for stainless steel, best drill bits for steel, cobalt vs HSS drill bits for steel, best drill for metal, best deburring tool for stainless steel, and the metal fab tools hub.

Scoring, line by line

Each bit is scored on performance, build, value, safety listing and warranty, with the weights published on the How We Pick page. Drill bits carry no electrical safety listing, so every set here scores zero on that criterion. No listing here states a warranty term, so every set scores zero on warranty too, and the ranking comes from performance, build and value.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
SEDIANAS M35 Cobalt Set 9.6 30 21 21 n/a 0
Pro Edge 7-Facet Stubby 9.6 29 21 20 n/a 0
DelitonGude 1/4 Inch M35 9.6 28 20 20 n/a 0
KSEIBI 3-Piece Step Bit 9.5 27 19 20 n/a 0

A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number. Safety points apply to gear that runs on power or lists safety features. Without either, we score out of 90 instead of 100.

More buying guides