Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Drill for Drilling Steel (2026): 4 Picks Compared

Four drill bit sets for steel, compared on material, tip angle, size range and shank, with the warranty each listing states.

Best Drill for Drilling Steel (2026): 4 Picks Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Diablo DMD-T29Best OverallDiablo DMD-T299.7/10View on Amazon
  2. 2STROTON M35 13-PieceBest Cobalt SetSTROTON M35 13-Piece9.6/10View on Amazon
  3. 3GuardPro 29-PieceWidest Size RangeGuardPro 29-Piece9.5/10View on Amazon
  4. 4ForgeWorx 1/4 Inch 2-PieceBest 1/4 Inch PairForgeWorx 1/4 Inch 2-Piece9.5/10View on Amazon

A bracket needs holes, the plate is steel, and the bit on the bench is the wrong kind for the job. The hole wanders, the edge goes dull, and the work stalls before the weld even starts. Picking the best drill for drilling steel starts with the bit itself: the material it is made from, the point it carries, and the sizes it covers. This guide compares bit sets on what each listing states, so the choice comes down to stated facts rather than guesswork.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall Diablo DMD-T29: A 29 piece set for mild, hardened and stainless steel, with a Thermal Shield coating, a 130 degree hybrid split point and a 3-flats shank. Check price on Amazon
  • Best Cobalt Set STROTON M35 13-Piece: Stated 5 percent cobalt M35 steel at 68 HRC, 13 pieces from 1/16 to 1/4 inch, with a split point and fully ground flutes. Check price on Amazon
  • Widest Size Range GuardPro 29-Piece: 29 pieces from 1/16 to 1/2 inch, a 135 degree split point, a black and gold oxide finish and a metal indexed storage case. Check price on Amazon
  • Best 1/4 Inch Pair ForgeWorx 1/4 Inch 2-Piece: Two 1/4 inch M35 cobalt bits with a TiAlN coating, a pilot point tip and a 1/4 inch hex shank. Check price on Amazon

The machines

Diablo Metal Demon Drill Bit Set

Diablo Metal Demon Drill Bit Set

Diablo9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 29 piece set built for metal only, with a Thermal Shield coating, a 130 degree hybrid split point and a 3-flats shank, made to drill mild, hardened and stainless steel.

Pros

  • Covers mild, hardened and stainless steel in one set, instead of separate titanium, cobalt and black oxide bits
  • Thermal Shield coating, claimed to extend bit life up to 30 times longer than standard metal drill bits
  • 130 degree hybrid split point for quick starts in stationary and handheld drills
  • The maker claims drilling speeds up to 2 times faster than other bits

Cons

  • Bit sizes are not stated in the listing
  • No steel grade is stated, only the coating name
  • No storage case is mentioned
  • No warranty term in the listing
STROTON Cobalt Drill Bit Set

STROTON Cobalt Drill Bit Set

STROTON9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 13 piece M35 cobalt set, 1/16 to 1/4 inch, with a stated 5 percent cobalt content and 68 HRC hardness, split point tips and a fully ground finish.

Pros

  • Stated 5 percent cobalt M35 steel at 68 HRC, the hardest stated material here
  • 13 sizes in 1/64 inch steps from 1/16 to 1/4 inch
  • Split point design with fully ground flutes, suited to heavy duty work in stainless steel, steel plate, iron sheet and cast iron
  • The maker claims 3 times the heat, wear and chip resistance and 3 times the tool life of ordinary bits

Cons

  • Top size is 1/4 inch, so larger holes need a different set
  • No storage case is mentioned
  • No shank type is stated
  • Jobber length only, so no stubby or extra long bits for tight or deep holes
GuardPro 29Pcs Cobalt Drill Bit Set

GuardPro 29Pcs Cobalt Drill Bit Set

GuardPro9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 29 piece high speed steel set covering 1/16 to 1/2 inch, with 135 degree split point tips, a black and gold oxide finish and a metal indexed storage case.

Pros

  • Widest size range here, 1/16 to 1/2 inch in 29 sizes
  • 135 degree split point with a self centering design that resists walking
  • Metal indexed storage case keeps the set sorted
  • 30 day money back term, the only stated money back term here

Cons

  • No cobalt content is stated
  • Largest bits need a chuck that opens to 1/2 inch
  • No bit length is stated
  • Only a 30 day money back term, no longer warranty
ForgeWorx 1/4 Inch Cobalt Drill Bits 2pcs

ForgeWorx 1/4 Inch Cobalt Drill Bits 2pcs

Forgeworx9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

Two 1/4 inch M35 cobalt bits with a TiAlN coating, a pilot point tip and a 1/4 inch hex shank, made for steel, cast iron and stainless steel.

Pros

  • M35 cobalt with a TiAlN coating, built for hard metals and high heat
  • Pilot point tip resists slipping and helps drilling speed, per the maker
  • Suited to steel, stainless steel, cast iron, titanium alloy and hard plastics
  • 4 inch length reaches deeper holes than a stubby bit

Cons

  • Only one size, 1/4 inch, so it covers a single hole size
  • Only 2 bits in the pack
  • No warranty term in the listing
  • No storage case is mentioned

Spec sheet comparison

Model Gear Score Bit count Size range Tip Material Shank Warranty
Diablo DMD-T29 9.7/10 29 Not stated 130 degree hybrid split point Not stated 3-flats None stated
STROTON M35 13-Piece 9.6/10 13 1/16 to 1/4 in Split point M35 HSS, 5% cobalt Not stated None stated
GuardPro 29-Piece 9.5/10 29 1/16 to 1/2 in 135 degree split point HSS, black and gold finish Round straight 30 day money back
ForgeWorx 1/4 Inch 2-Piece 9.5/10 2 1/4 in Pilot point M35 cobalt, TiAlN coating 1/4 in hex None stated

These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 20 November 2026.

Buying guide: picking the best drill for drilling steel

Bit material

The listings here split between cobalt and high speed steel. The ForgeWorx and STROTON sets state M35 cobalt, with STROTON adding a stated 5 percent cobalt content and 68 HRC hardness. STROTON claims 3 times the heat, wear and chip resistance of ordinary bits, and ForgeWorx points to M35 cobalt for abrasion and high heat. The Diablo set names its Thermal Shield coating rather than a steel grade, and the GuardPro bullets describe high speed steel with a black and gold oxide finish. When a listing states no grade, treat the bit as a general purpose steel drilling bit rather than a hardened steel bit.

Tip angle and point

The point decides whether the bit starts where it is aimed. The GuardPro set uses a 135 degree split point, the Diablo a 130 degree hybrid split point, and the STROTON a split point with fully ground flutes. The ForgeWorx pair uses a pilot point tip, which the maker says prevents slipping and helps drilling speed. The Diablo listing notes its split point works in both stationary and handheld drills, preventing walking and keeping holes accurate.

Size range and count

Range decides how many holes the set can drill without another purchase. The GuardPro set covers 1/16 to 1/2 inch in 29 sizes, the widest range here. The STROTON set covers 1/16 to 1/4 inch in 13 sizes, stepping in 1/64 inch increments. The Diablo set lists 29 pieces with no stated sizes, and the ForgeWorx pack holds two bits of 1/4 inch. Match the range to the holes the shop drills most, and check the largest size against the chuck.

Shank

The shank is what the chuck grips. The ForgeWorx bits have a 1/4 inch hex shank, the GuardPro bits a round straight shank, and the Diablo set a 3-flats shank. The STROTON listing states no shank type. Check the shank against the chuck before ordering, since the listings do not all state it.

Storage

Only the GuardPro set states a storage case, a metal indexed case that keeps the set sorted. The Diablo, STROTON and ForgeWorx listings state no case, so plan where the bits will live in the shop.

Use as directed. Clamp the work before drilling, wear eye and face protection, and keep gloves away from rotating parts. Keep guards in place on the drill press, and never exceed the rated capacity of the machine. See the OSHA machine guarding guide and our Safety Disclaimer.

Before You Strike an Arc

  • Check the shank fits the chuck: hex, round straight and 3-flats shanks all appear in this guide, and the STROTON listing states no shank type, so check it on arrival.
  • Clamp the work to the bench or the drill press table before the bit touches steel.
  • Wear eye and face protection, and keep gloves away from rotating parts.
  • Start the hole with the split or pilot point on the mark, and let the point center the bit before leaning on the feed.
  • Count the bits and check the sizes on arrival, since some listings in this guide give counts that disagree inside the listing.

FAQ for welders

What is the best drill for drilling steel?

The best drill for drilling steel in this guide is the Diablo DMD-T29, which scores highest on the stated coating, tip and range. It is a 29 piece set made for mild, hardened and stainless steel, with a Thermal Shield coating and a 130 degree hybrid split point. For a cobalt set, the STROTON 13 piece set states 5 percent cobalt at 68 HRC.

What size drill bit do I need for steel?

It depends on the hole. The GuardPro set covers 1/16 to 1/2 inch in 29 sizes, the widest range here, while the STROTON set covers 1/16 to 1/4 inch in 13 sizes. The ForgeWorx pack holds 1/4 inch bits only, so it suits a shop that drills that size often.

Are cobalt drill bits better than high speed steel for steel?

The cobalt listings here claim the edge. STROTON claims 3 times the heat, wear and chip resistance of ordinary bits, and ForgeWorx describes M35 cobalt as built for hard metals and high heat. The GuardPro set describes high speed steel with a black and gold oxide finish, which suits general steel drilling.

What tip angle works for drilling steel?

The sets here use 130 and 135 degree split points. The Diablo set uses a 130 degree hybrid split point, and the GuardPro set uses a 135 degree split point with a self centering design. The ForgeWorx pair uses a pilot point tip instead, which the maker says prevents slipping.

Do I need cutting fluid when drilling steel?

None of the listings here include a cutting fluid. For options, see our best cutting fluid for steel picks, which cover drilling, tapping and sawing.

Related: sheet metal and tubing hub, best drill for metal work, best drill bit for stainless steel metal, best drill bit to drill through steel, and best drill bit set for hard steel. Also see our best cutting fluid for steel. Also see our drilling tips for metal. Also see our best drill bit to drill through metal. Also see our drilling and tapping chart.

Scoring, line by line

Each bit set is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. Drill bits have no electrical safety listing to state, so every set here scores zero on that criterion; the ranking comes from the other four.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Diablo DMD-T29 9.7 32 22 21 n/a 0
STROTON M35 13-Piece 9.6 30 21 21 n/a 0
GuardPro 29-Piece 9.5 27 19 20 n/a 2
ForgeWorx 1/4 Inch 2-Piece 9.5 28 20 19 n/a 0

Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.

More buying guides