Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Drill Bit to Drill Through Metal (2026): 5 Picks Compared

5 step and cobalt drill bits for drilling through metal, compared on size range, coating, shank and case, from 10 to 50 sizes.

Best Drill Bit to Drill Through Metal (2026): 5 Picks Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Forgeworx Cobalt 1/8 inBest OverallForgeworx Cobalt 1/8 in9.5/10View on Amazon
  2. 2EASTPACE 13-Piece CobaltBest SetEASTPACE 13-Piece Cobalt9.5/10View on Amazon
  3. 3NEIKO 10193ABest Step SetNEIKO 10193A9.5/10View on Amazon
  4. 4IRONANT Step Bit SetWidest Size CountIRONANT Step Bit Set9.5/10View on Amazon

A dull bit skating across steel wastes the afternoon and ruins the hole. When the job is a bracket, a hinge or a patch panel, the bit has to bite clean and hold its edge, and that is what the best drill bit to drill through metal has to do. This guide compares the bits below on size range, coating, shank and case.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall Forgeworx Cobalt 1/8 in: M35 cobalt with a TiAlN coating and a pilot point, in 1/8 in by 4 in, for hardened steel, stainless steel and cast iron. Check price on Amazon
  • Best Set EASTPACE 13-Piece Cobalt: 13 M35 cobalt bits from 1/16 to 1/4 in with a 135° split point and an indexed case. Check price on Amazon
  • Best Step Set NEIKO 10193A: 3 step bits covering 28 sizes from 1/8 to 3/4 in, with a two-flute design and a tri-flat shank. Check price on Amazon
  • Widest Size Count IRONANT Step Bit Set: 5 step bits with 50 sizes and an aluminum case, for sheet metal, aluminum, iron and plastic. Check price on Amazon

The machines

ForgeWorx 1/8 Inch Cobalt Drill Bits 2pcs

ForgeWorx 1/8 Inch Cobalt Drill Bits 2pcs

Forgeworx9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 2-piece set of 1/8 in by 4 in M35 cobalt bits with a TiAlN coating, a pilot point and a 1/4 in hex shank, made for hardened steel, stainless steel and cast iron.

Pros

  • M35 cobalt with a TiAlN coating for hardened steel, stainless steel and cast iron
  • Pilot point tip that prevents slipping and speeds drilling
  • 1/4 in hex shank for a firm grip in the chuck
  • 4 in length gives reach for deeper holes

Cons

  • Only 2 bits, both the same 1/8 in size
  • No case, so the bits need separate storage
  • One size only, so larger holes need another bit
  • Hex shank needs a chuck that accepts 1/4 in hex bits
EASTPACE 13Pcs M35 Cobalt Drill Bit Set

EASTPACE 13Pcs M35 Cobalt Drill Bit Set

EASTPACE9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 13-piece M35 cobalt set from 1/16 to 1/4 in with a 135° split point and an indexed case.

Pros

  • 13 sizes from 1/16 to 1/4 in in one set
  • M35 cobalt with 5% cobalt for wear resistance and durability
  • 135° split point for faster cutting and self-centering
  • Indexed case keeps the 13 bits in order

Cons

  • Largest size is 1/4 in, so bigger holes need another bit
  • No coating is stated, unlike the TiAlN coated sets here
  • The smallest sizes need care with speed, pressure and heat control
  • Small bits need a light touch to stay on line
Neiko 10193A Titanium Step Bits, Unibit Set

Neiko 10193A Titanium Step Bits, Unibit Set

NEIKO9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3-piece titanium step bit set that replaces 28 drill bits, with steps from 1/8 to 3/4 in and a tri-flat shank.

Pros

  • 3 step bits cover 28 sizes from 1/8 to 3/4 in
  • Titanium coated HSS with a two-flute spiral design
  • Tri-flat shank for a firm grip in the chuck
  • Cuts and deburrs as it drills, with only a small amount of pressure

Cons

  • Step bits suit sheet metal, not thick plate or hardened steel
  • Only 3 bits, so a damaged step loses a size range
  • No case, so the bits need separate storage
  • The largest step is 3/4 in, so bigger holes need another tool
IRONANT 5PCS Spiral Flute Titanium HSS Step Drill

IRONANT 5PCS Spiral Flute Titanium HSS Step Drill

IRONANT9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-piece spiral flute step bit set with 50 sizes, a titanium coating and an aluminum case, for sheet metal, aluminum, iron and plastic.

Pros

  • 50 sizes in 5 pieces, the widest size count here
  • 118° split point tip with a spiral dual-flute design
  • Aluminum case keeps the 5 bits organized
  • Self-centering tip prevents walking on sheet metal

Cons

  • Not recommended for stainless steel or any other harder metal
  • No size range is stated, only the count of 50 sizes
  • No warranty term is stated
  • Made for sheet metal and softer metals, so hard plate is out of range
Anfrere 10 Sizes Step Drill Bit for Metal Sheet

Anfrere 10 Sizes Step Drill Bit for Metal Sheet

Anfrere9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

One step bit with 10 sizes from 1/4 to 1-3/8 in, in titanium coated HSS with double flutes, for sheet metal, aluminum, copper, plastic and wood board.

Pros

  • 10 sizes from 1/4 to 1-3/8 in on one bit
  • Titanium coated HSS for durability and sharpness
  • Double flutes let particles escape for clean drilling
  • Weighs 0.31 pounds as listed

Cons

  • Stated uses exclude steel or harder metal, so it is a sheet metal bit only
  • One bit only, so a damaged step ends the set
  • No case, so the bit needs separate storage
  • No warranty term is stated

Other welders and gear to compare

Spec sheet comparison

Model Bit type Sizes Material Shank Case
Forgeworx Cobalt 1/8 in Cobalt twist bit 1/8 in M35 cobalt, TiAlN 1/4 in hex Not stated
EASTPACE 13-Piece Cobalt Cobalt twist bit set 13 sizes, 1/16 to 1/4 in M35 cobalt, 5% Not stated Indexed case
NEIKO 10193A Step bit set 28 sizes, 1/8 to 3/4 in Titanium coated HSS Tri-flat Not stated
IRONANT Step Bit Set Step bit set 50 sizes Titanium coated HSS Not stated Aluminum case
Anfrere 10-Size Step Bit Step bit 10 sizes, 1/4 to 1-3/8 in Titanium coated HSS Not stated Not stated

All specs here repeat what the maker rates and the listing prints, copied down 15 November 2026.

Buying guide: best drill bit to drill through metal

Step bits or twist bits

Step bits open a hole in stages, so one bit covers many sizes: the NEIKO set covers 28 sizes with 3 bits, the IRONANT set covers 50 sizes with 5 pieces, and the Anfrere bit covers 10 sizes on its own. Twist bits cut one size each, so the EASTPACE set covers 13 sizes from 1/16 to 1/4 in. For hardened steel, the cobalt twist bits are the stated match.

Cobalt or titanium coating

M35 cobalt is the harder material here, stated for hardened steel, stainless steel, cast iron and titanium alloy on the Forgeworx bits, and for stainless steel, cast iron and hardened steel on the EASTPACE set, which states 5% cobalt. Titanium coated HSS is the step bit material, stated for sheet metal, aluminum, copper and plastic.

Size range

Match the range to the holes you drill. The NEIKO set runs from 1/8 to 3/4 in, the Anfrere bit from 1/4 to 1-3/8 in, and the EASTPACE set from 1/16 to 1/4 in. The IRONANT set states a count of 50 sizes without a stated range, and the Forgeworx set is one 1/8 in size.

Shank and grip

The Forgeworx bits use a 1/4 in hex shank, and the NEIKO set uses a tri-flat shank, both made to grip firm in the chuck. Check the shank against the chuck before ordering.

Sheet metal or hardened steel

Sheet metal is the step bit’s home ground: the NEIKO, IRONANT and Anfrere bits all state sheet metal as a use, and the NEIKO set also states stainless steel. Hardened steel, cast iron and titanium alloy are the cobalt bits’ ground, stated on the Forgeworx and EASTPACE bits.

Use as directed. Clamp the work before drilling, wear eye and face protection, keep gloves away from rotating parts, and keep guards in place on the drill press. Let the bit cut at its own pace and clear chips before the hole closes. OSHA machine guarding guidance covers guards and clamping.

Before You Strike an Arc

  • Check the shank before ordering: the Forgeworx bits use a 1/4 in hex shank and the NEIKO set uses a tri-flat shank, so both need a chuck that grips them.
  • Match the size range to the hole: the step sets cover 1/8 to 3/4 in and 1/4 to 1-3/8 in.
  • Check the stated metals: the cobalt bits list hardened steel and stainless steel, while the IRONANT and Anfrere bits exclude harder metal.
  • Keep the case with the set: the IRONANT set comes in an aluminum case and the EASTPACE set in an indexed case, so the sizes stay in order.
  • Check the count on arrival: the NEIKO set has 3 bits, the IRONANT set has 5 pieces and the EASTPACE set has 13 pieces.

FAQ for welders

What is the best drill bit to drill through metal?

For hardened steel, stainless steel and cast iron, the cobalt twist bits here are the match: the Forgeworx 1/8 in bits and the EASTPACE 13-piece set, both in M35 cobalt.

Can a step drill bit drill through steel?

The step sets here suit sheet metal. The IRONANT set is not recommended for stainless steel or any other harder metal, and the Anfrere bit excludes steel or any other harder metal, so for steel plate use a cobalt twist bit.

Do I need a cobalt drill bit for stainless steel?

The two cobalt sets here state it as a use: Forgeworx lists stainless steel, cast iron and titanium alloy, and EASTPACE lists stainless steel, cast iron and hardened steel.

How many sizes does a step drill bit cover?

The sets here cover 10, 28 and 50 sizes: Anfrere covers 10 sizes from 1/4 to 1-3/8 in, NEIKO covers 28 sizes with 3 bits, and IRONANT covers 50 sizes with 5 pieces.

What does a TiAlN coating do?

TiAlN is the coating stated on the Forgeworx bits, and the maker states it gives resistance against abrasion and high heat. The IRONANT set also states a titanium coating for sharpness and durability.

Related: best twist drill bit set, best drill bit set for metal, best drill bit to drill through steel, best step drill bit for sheet metal, HSS vs cobalt drill bit, step drill bit vs hole saw for sheet metal, best drill bit for drilling metal, and the metal fab tools hub.

Scoring, line by line

Each bit is scored out of 10 on performance, build, value, safety and warranty, using only what each maker states. The weights are on our How We Pick page. No safety listing or warranty term is stated for any bit here, so the ranking comes from performance, build and value.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Forgeworx Cobalt 1/8 in 9.5 32 22 21 0 0
EASTPACE 13-Piece Cobalt 9.5 30 21 22 0 0
NEIKO 10193A 9.5 30 21 21 0 0
IRONANT Step Bit Set 9.5 29 21 21 0 0
Anfrere 10-Size Step Bit 9.4 26 20 20 0 0

A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number.

More buying guides