Best Drill Bit to Drill Through Steel (2026): 5 Picks Compared
5 cobalt and titanium drill bits for steel compared on material, sizes, point angle, shank and warranty, with every figure taken from the listings.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallAugTouf M35 Step Bit9.7/10View on Amazon - 2
Best Twist SetSabre 1/4 in Cobalt Bits9.7/10View on Amazon - 3
Best Metric SetMACXCOIP M35 Cobalt Set9.6/10View on Amazon - 4
Best Step SetSEDIANAS Titanium Step Bits9.6/10View on Amazon - 5
Best One-Bit StepIRONANT Spiral Step Bit9.5/10View on Amazon
A bracket needs holes, the steel is already cut, and the best drill bit to drill through steel is the one that cuts clean without wandering off the mark. This article compares drill bits for steel on material, sizes, point angle, shank and warranty, with every figure taken from the listings. The AugTouf cobalt step bit leads because it states cobalt, a TiAlN coat and a warranty, while the twist-bit sets suit repeated holes of one size.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall AugTouf M35 Step Bit: M35 cobalt with TiAlN coat and a 90-day warranty Check price on Amazon
- Best Twist Set Sabre 1/4 in Cobalt Bits: 5 cobalt bits in 1/4 in size for steel and cast iron Check price on Amazon
- Best Metric Set MACXCOIP M35 Cobalt Set: 13 metric cobalt bits from 1.5 to 6.5 mm Check price on Amazon
- Best Step Set SEDIANAS Titanium Step Bits: 50 sizes across 5 step bits with a storage case Check price on Amazon
- Best One-Bit Step IRONANT Spiral Step Bit: 10 sizes on one bit from 1/4 to 1-3/8 in Check price on Amazon
The machines

toolant M35 Cobalt Step Drill Bit, 3/16"-7/8"
One M35 cobalt step bit with TiAlN coating, 12 step sizes from 3/16 to 7/8 in and a 1/4 in hex shank.
Pros
- M35 cobalt HSS with TiAlN coating and 89HRC surface hardness stated
- 12 step sizes from 3/16 to 7/8 in on one bit
- Suits 1/8 in thick stainless steel and metal sheet, per the listing
- 90 days warranty of free replacement or refund stated
Cons
- One bit only, so one size range covers the job
- No certification is stated
- 3.34 inches long, shorter than the 4 in Sabre bits
- The maker notes the hex shank can snap off

Sabre Tools 1/4 Inch Cobalt Drill Bits 5pcs
5 cobalt twist bits in 1/4 in size, 4 in long, with a pilot point tip for steel and cast iron.
Pros
- M35 cobalt with a pilot point tip that prevents slipping
- Suits steel, cast iron, stainless steel and titanium alloy
- 5 bits in the same 1/4 in size for repeated holes
- Heavy-duty build with resistance against abrasion and high heat, as the maker states
Cons
- No warranty term is stated
- No certification is stated
- Only one size: 1/4 in, with no other diameters in the box
- No storage case is stated

MACXCOIP Metric 13Pcs(1.5mm-6.5mm)
A 13-piece metric M35 cobalt twist bit set from 1.5 to 6.5 mm with a 135 degree point and a storage box.
Pros
- 13 metric sizes from 1.5 to 6.5 mm in one box
- M35 cobalt for hardened metals, stainless steel and cast iron
- 135 degree point tip with a twist design for faster cutting and self-centering
- Storage box with size indexes for sorting
Cons
- No warranty term is stated
- No certification is stated
- Not applicable to quenched bolts, per the listing
- Largest bit is 6.5 mm, so bigger holes need another set

5PCS Titanium Step Drill Bit
A 5-piece titanium step bit set with four spiral flutes, 50 sizes from 3/16 to 1-3/8 in and a storage case.
Pros
- 50 sizes across 5 step bits, from 3/16 to 1-3/8 in
- 135 degree split point tip with self-centering to prevent walking
- Four-spiral flute design clears chips and reduces clogging
- Storage case with clear size markings on each bit
Cons
- Not recommended for stainless steel or harder metal, per the listing
- HSS with a titanium coating, not cobalt, for hard steel
- No shank size is stated
- No hardness figure is stated, unlike the 89HRC on the AugTouf bit

IRONANT Spiral Flute 1/4" to 1-3/8" Step Drill Bit
One HSS step bit with a titanium coat, 10 sizes from 1/4 to 1-3/8 in and a 118 degree split point.
Pros
- 10 sizes on one bit, from 1/4 to 1-3/8 in
- 118 degree split point tip with self-centering to prevent walking
- Spiral dual-flute design clears chips faster
- 0.33 pounds, light in the hand for sheet work
Cons
- Not recommended for stainless steel or harder metal, per the listing
- HSS with a titanium coat, not cobalt, for hard steel
- No shank size is stated
- No storage case is stated
Other welders and gear to compare
ZELCAN 10 Sizes Titanium Step Drill BitCheck price on Amazon
Anfrere 10 Sizes Step Drill Bit for Metal SheetCheck price on Amazon
NEIKO 10047A Extra Long Drill Bit SetCheck price on Amazon
EZARC M35 Cobalt Stubby Drill Bit Set for Hard MetalCheck price on Amazon
Crosstar 21Pcs M35 Cobalt Drill Bit SetCheck price on Amazon
Spec sheet comparison
| Bit | Gear Score | Type | Sizes | Material | Shank | Warranty |
|---|---|---|---|---|---|---|
| AugTouf M35 Step Bit | 9.7/10 | Step bit | 12 sizes, 3/16-7/8 in | M35 cobalt, TiAlN | 1/4 in hex | 90 days |
| Sabre 1/4 in Cobalt Bits | 9.7/10 | Twist bits | 5 bits, 1/4 in | M35 cobalt | Not stated | Not stated |
| MACXCOIP M35 Cobalt Set | 9.6/10 | Twist bits | 13 pcs, 1.5-6.5 mm | M35 cobalt | Not stated | Not stated |
| SEDIANAS Titanium Step Bits | 9.6/10 | Step bits | 50 sizes, 3/16-1-3/8 in | HSS, titanium coat | Not stated | Not stated |
| IRONANT Spiral Step Bit | 9.5/10 | Step bit | 10 sizes, 1/4-1-3/8 in | HSS, titanium coat | Not stated | Not stated |
Treat the specs as maker ratings pulled straight from the listings; we gathered them on 15 November 2026.
Buying guide: the best drill bit to drill through steel
Cobalt or titanium-coated HSS
3 bits here state M35 cobalt: the AugTouf step bit, the Sabre twist bits and the MACXCOIP set. The SEDIANAS and IRONANT bits state HSS with a titanium coat. Cobalt suits stainless steel and harder metal, and the AugTouf bit states it suits 1/8 in thick stainless steel sheet, while the SEDIANAS and IRONANT listings say they are not recommended for stainless steel or harder metal. See our HSS vs cobalt drill bit guide for the full comparison.
Step bits or twist bits
Step bits drill many hole sizes with one bit: the AugTouf bit covers 12 sizes, the IRONANT bit 10 sizes and the SEDIANAS set 50 sizes across 5 bits. Twist bits drill one size each: the Sabre set holds 5 bits in 1/4 in size, and the MACXCOIP set holds 13 metric bits from 1.5 to 6.5 mm. Step bits suit sheet metal; twist bits suit repeated holes and deeper work. See our step drill bit vs twist drill bit guide for the trade-offs.
Point angle and split points
The SEDIANAS set and the MACXCOIP set state a 135 degree point, and the IRONANT bit states a 118 degree split point. Split points center themselves and prevent walking, which matters when the bit bites into steel. The AugTouf bit states a 135 degree split point tip as well, while the Sabre bits state a pilot point tip that prevents slipping.
Thickness the bit can handle
Only the AugTouf bit states a thickness: it suits 1/8 in thick stainless steel and metal sheet. The SEDIANAS and IRONANT bits state sheet metal, aluminum and iron, and the Sabre and MACXCOIP bits state hard metals, stainless steel and cast iron without a thickness figure. A step bit cuts thin sheet well and struggles as the metal gets thicker, so match the bit to the thickness on the job and check the listing before ordering.
Shank and chuck fit
Only the AugTouf bit states a shank: a 1/4 in hex shank. The other 4 bits state no shank size, so check the shank against the chuck before ordering. The AugTouf warranty note says to contact the maker if the hex shank snaps off, so seat the shank fully and keep the chuck tight.
Size range and count
Count the sizes, not just the bits. The SEDIANAS set covers 50 sizes from 3/16 to 1-3/8 in, the AugTouf bit covers 12 sizes from 3/16 to 7/8 in, and the IRONANT bit covers 10 sizes from 1/4 to 1-3/8 in. The MACXCOIP set covers 13 metric sizes from 1.5 to 6.5 mm, and the Sabre set covers one size, 1/4 in, with 5 bits. Match the range to the holes on the job, and check the size markings on the bit before drilling.
Use as directed. Clamp the work, wear eye protection, and keep gloves away from rotating parts. Never exceed the stated thickness the listing gives for a bit, and stop if the bit smokes or wanders. See our drill press safety guide.
Before You Strike an Arc
- Clamp the work before drilling: a bit that catches can spin the piece.
- Wear eye protection: chips fly off steel, and step bits throw them clear.
- Keep gloves away from rotating parts: no gloves near a spinning bit or chuck.
- Check the shank and size markings on arrival: the AugTouf bit states a 1/4 in hex shank, and the SEDIANAS bits carry clear size markings.
- Check the bit suits the metal: the SEDIANAS and IRONANT bits are not recommended for stainless steel or harder metal.
FAQ for welders
Which bit here suits stainless steel?
The AugTouf step bit, which states it suits 1/8 in thick stainless steel sheet, and the Sabre and MACXCOIP cobalt bits, which state stainless steel among the metals they suit. The SEDIANAS and IRONANT bits state they are not recommended for stainless steel.
What is the difference between a step bit and a twist bit?
A step bit drills many hole sizes with one bit: the AugTouf bit covers 12 sizes and the IRONANT bit 10 sizes. A twist bit drills one size: the Sabre set holds 5 bits in 1/4 in size and the MACXCOIP set holds 13 metric bits from 1.5 to 6.5 mm.
Which bit has the most sizes?
The SEDIANAS set, with 50 sizes across 5 step bits from 3/16 to 1-3/8 in.
Do any of these bits state a warranty?
Only the AugTouf bit, with a 90 days warranty of free replacement or refund. The other 4 bits state no warranty term.
What shank does the AugTouf bit use?
A 1/4 in hex shank. The other 4 bits state no shank size.
Related: best drill bit to drill hardened steel, best drill bits for drilling stainless steel, best drill bit for drilling metal, best cobalt drill bit set, best step drill bit for sheet metal, cobalt vs HSS drill bits for steel, titanium vs cobalt drill bits, annular cutter vs twist drill bit, best drill bit set for metal, drill bit tips, do drill bit sharpeners work, how to clean rusty drill bits, types of drill bit, best twist drill bit set, titanium vs black oxide drill bits, carbide vs cobalt drill bits, best step drill bit for auto body, best drill for metal, drill press speed chart, and the metal fab tools hub.
Scoring, line by line
Each bit is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. Drill bits have no electrical safety listing to state, so every bit here scores zero on that criterion; the ranking comes from the other four.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| AugTouf M35 Step Bit | 9.7 | 32 | 22 | 21 | n/a | 3 |
| Sabre 1/4 in Cobalt Bits | 9.7 | 30 | 22 | 21 | n/a | 0 |
| MACXCOIP M35 Cobalt Set | 9.6 | 30 | 21 | 21 | n/a | 0 |
| SEDIANAS Titanium Step Bits | 9.6 | 28 | 20 | 21 | n/a | 0 |
| IRONANT Spiral Step Bit | 9.5 | 27 | 20 | 20 | n/a | 0 |
Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.




