Drill Bit Tips for Metal and Fabrication
Drill bit tips for metal work: pick the right twist bit, clamp the work, mark the hole, and drill with steady pressure while the flutes clear the chips.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
BOSCH CO21B 21-Piece Assorted Set with Included Case Cobalt9.7/10View on Amazon - 2
MACXCOIP 29Pcs9.7/10View on Amazon - 3
MACXCOIP 60Pcs9.7/10View on Amazon
A drill bit only cuts well when the bit, the metal and the setup agree. Get the bit choice wrong and the hole wanders, the edge dulls, and the bit squeals instead of cutting. These drill bit tips cover picking the right bit for metal, setting up the hole, and drilling it clean, using the sizes and figures the listings below actually state.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Drill bit tips for metal, in short
Start with a sharp bit that matches the metal. A 135-degree split point starts on contact and resists walking, and the Drill America, Makita, DEWALT and HURRICANE listings below state that point angle, while the COMOWARE titanium set does not state one. Clamp the work, mark the hole, and drill with steady pressure while the flutes clear the chips. Stop when the bit gets hot, clear the chips, and let the bit cool before the next pass.
Pick the right bit for the metal
High speed steel twist bits are the baseline for metal work. The Drill America set in the reference listings runs from 1/16 to 1/2 inch in 1/64 inch steps, which covers small pilot holes up to bolt holes in plate. Its black and gold oxide finish resists corrosion, and the self-centering 135-degree split point penetrates hard material without a pilot hole.
Titanium coated bits add a hard surface to the same high speed steel. The COMOWARE set lists a titanium coating over high speed steel with 2 flutes that clear chips and cut friction and heat, while the Makita set lists a titanium nitride coating and a 135-degree split point for faster starts. The COMOWARE set covers 1/16 to 1/4 inch with a 1/4 inch hex shank that locks into a quick change chuck.
Black oxide bits sit in the middle on finish: the DEWALT 21-piece set lists a black oxide coating that helps resist corrosion, a 135-degree split point, and a 31-degree helix that the maker lists for deep holes. Its parabolic flute design moves chips out of the hole in metal and wood.
Big combo kits trade focus for range. The COMOWARE 246-piece (on Amazon) set lists 57 titanium drill bits, 30 black oxide twist bits, 21 masonry bits and 17 brad point bits alongside screwdriver bits, while the HURRICANE 230-piece (on Amazon) set lists titanium twist bits from 3/64 to 1/2 inch. These kits suit a home garage that drills a little of everything, but the size counts list the most pieces in the smallest sizes, so check the set holds the sizes you drill most.
Screwdriver bits are not drill bits, even when they share a case. The DEWALT 40-piece set lists driver bits, nut drivers and a bit holder for driving screws, not for drilling holes. The DEWALT 100-piece (on Amazon) set and the CRAFTSMAN 140-piece (on Amazon) set mix both: they list 14 and 21 drill bits respectively alongside driver bits, so check the contents before assuming a set is drivers only. Keep driver bits out of the drill when the job needs a hole.
Side by side
| HSS twist bit | Titanium coated bit | Black oxide bit | |
|---|---|---|---|
| Point | 135-degree split point | 135-degree split point (Makita); not stated (COMOWARE) | 135-degree split point |
| Sizes listed | 1/16 to 1/2 inch | 1/16 to 1/4 inch (COMOWARE); not stated (Makita) | 1/16 to 1/2 inch |
| Flutes | Not stated | 2 flutes (COMOWARE); not stated (Makita) | Parabolic flute |
| Coating | Black and gold oxide | Titanium or titanium nitride | Black oxide |
| Shank | Not stated | 1/4 inch hex shank | Not stated |
| Sets in the listings | 29-piece set | 16-piece and 14-piece sets | 21-piece set |
The table above lines up the 3 twist bit finishes from the reference listings. The Drill America, Makita and DEWALT sets state a 135-degree split point, so the choice comes down to coating, sizes and shank.
Set up the hole before you drill
Clamp the work to the table so it cannot spin when the bit breaks through. Mark the hole with a center punch so the split point has a seat to start in. A 1/4 inch hex shank bit seats in a quick change chuck, while a round shank bit needs the chuck jaws tightened on the shank itself. Check that the bit runs true before you touch metal: a wobbling bit drills an oversize hole and dulls fast.
Eye and face protection comes before anything else on every drilling job, and the work stays clamped for the whole hole. Keep gloves away from rotating parts, keep guards in place, and keep the chuck key out of the chuck before you pull the trigger. See the OSHA machine guarding page for the guarding rules that cover drill presses and rotating tools.
Drill the hole
Start slow so the split point bites, then feed with steady pressure and let the bit cut. Back the bit out often to clear chips from the flutes, since packed chips rub, heat the bit and dull the edge. The COMOWARE listing notes that 2 flutes help clear chips away from the bit and cut friction and heat, which is the same reason to peck rather than push straight through.
Watch the chips: long curls mean the bit is cutting, while dust or blue chips mean heat is building and the edge is suffering. Stop, clear the hole, and let the bit cool. A dull bit needs sharpening or replacing, not more pressure.
Keep the bits sharp and stored
Bits dull from heat and from knocking against each other in a drawer. The COMOWARE 246-piece set ships in a portable storage case with a sponge cushion that the maker lists to stop bits falling out or mixing, and the HURRICANE set ships in a hard storage box. Keep bits in the indexed holder or case they came with, with the size labels facing out so you grab the right bit without hunting.
Sharpening is a separate skill, but the sign of a dull bit is plain: it squeals, it pushes hard, and it leaves a ragged hole. Swap in a fresh bit from the set rather than forcing a dull bit, and keep a spare of the sizes you use most. The DEWALT 21-piece set lists 1/16 and 1/8 and 1/4 inch bits in pairs.
FAQ for welders
What drill bit is best for metal?
A high speed steel twist bit with a 135-degree split point is the usual pick for metal, and the Drill America, Makita, DEWALT and HURRICANE listings state that point angle. Titanium coating adds surface hardness, while black oxide helps resist corrosion. Match the bit to the metal and the hole size, and keep the bit sharp.
Why does my drill bit keep walking?
A bit walks when the point has no seat to start in, or when the point angle is wrong for the metal. A 135-degree split point starts on contact and resists walking, and a center punch mark gives the point a seat. Clamp the work and start slow so the point bites before you add pressure.
Can I use a titanium drill bit on stainless steel?
The Makita set lists drilling in ferrous metal, wood, plastic, non-ferrous metal, cast iron and stainless steel, and its titanium nitride coating is listed for longer life than non-coated bits. Start slow, keep the bit cool, and clear the chips so heat does not build in the hole.
What size drill bit do I need for a bolt hole?
Pick the bit size from the bolt size, not from a rule of thumb, and check the set you own. The Drill America set runs from 1/16 to 1/2 inch in 1/64 inch steps, and the HURRICANE set runs from 3/64 to 1/2 inch, so a full index set covers most bolt holes without a special order. For a larger hole, drill a pilot hole before the full-size hole.
How do I keep a drill bit from getting dull?
Keep the bit cool, clear the chips, and do not force it. The COMOWARE listing notes that 2 flutes clear chips away from the bit and cut friction and heat, and the same habit keeps any twist bit cutting longer. Store bits in the indexed case they came with so the edges do not knock against each other.
Related: best twist drill bit set, best drill bit set for wood and metal, best step drill bit for sheet metal, and the metal fab tools hub.




