Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How to Clean Rusty Drill Bits: A Shop Guide

Surface rust comes off drill bits with the right wire brush on a drill, and this guide shows the steps, the brush shapes and when a bit is past saving.

How to Clean Rusty Drill Bits: A Shop Guide
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Holikme 12Pcs Wire Brush for DrillHolikme 12Pcs Wire Brush for Drill9.6/10View on Amazon
  2. 2Drill Wire Brush Set - 0.012 Carbon Steel WireDrill Wire Brush Set - 0.012 Carbon Steel Wire9.6/10View on Amazon
  3. 3SBGGRL 9 Pcs Wire Brush for Drill Set,Steel WoolSBGGRL 9 Pcs Wire Brush for Drill Set,Steel Wool9.5/10View on Amazon
  4. 4POLIWELL Nylon Wire Wheel Cup Brush SetPOLIWELL Nylon Wire Wheel Cup Brush Set9.5/10View on Amazon

Rusty drill bits still cut once the rust is off the flutes and the cutting edge, and the fix is simple hand work at the bench: brush the rust away, wipe the bit clean, dry it fully, then protect it so the rust does not come straight back. This guide shows how to clean rusty drill bits with a wire brush set on a drill, which brush shape suits each part of the bit, and when a bit is too far gone to save.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Holikme 12Pcs Wire Brush for Drill

Holikme 12Pcs Wire Brush for Drill

Holikme9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 12-piece set with 3 cup, 3 wheel, 3 pen and 3 straight brushes on a quarter-inch hex shank, with a stated limit of 4500 RPM.

Pros

  • 12 pieces cover cup, wheel, pen and straight shapes in one set
  • Pen and straight brushes reach corners and narrow recesses
  • Quarter-inch hex shank fits most drills and impact drivers
  • Reinforced base plate limits bristle shedding under heavy pressure

Cons

  • Cup brushes are wide for small bits and tight flutes
  • Carbon steel wire can mark a polished bit face
  • No nylon brush for delicate or coated bits
  • No warranty term is stated
Drill Wire Brush Set - 0.012 Carbon Steel Wire

Drill Wire Brush Set - 0.012 Carbon Steel Wire

Romeda9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-piece set with 0.012 inch carbon steel wire in 75 mm, 50 mm, 65 mm and 25 mm brush sizes, rated to 4500 RPM.

Pros

  • 0.012 inch carbon steel wire is stated for a known bite
  • 75 mm, 50 mm, 65 mm and 25 mm sizes cover large faces and small spots
  • Cup brush sits in a safety-designed metal holder
  • Rated for high-speed use at 4500 RPM

Cons

  • Only 5 pieces, fewer brushes than the larger sets
  • No pen or straight brush for narrow recesses
  • 75 mm wheel is wide for small bits
  • No warranty term is stated
SBGGRL 9 Pcs Wire Brush for Drill Set,Steel Wool

SBGGRL 9 Pcs Wire Brush for Drill Set,Steel Wool

SBGGRL9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 9-piece set of cup, wheel and end brushes with crimped carbon steel wire, made to run up to 4500 RPM.

Pros

  • 9 pieces give cup, wheel and end shapes for faces, edges and tight spots
  • Crimped carbon steel wire cuts tough rust, paint and corrosion
  • Reinforced wires resist shedding at high speed
  • Maker states the quarter-inch shank fits drills, angle grinders and rotary tools

Cons

  • Cup brush is wide for narrow flutes and small bits
  • Aggressive wire can scratch a polished bit face
  • Round shank holds less firmly than a hex shank in a worn chuck
  • No nylon brush for gentle cleaning of coated bits
POLIWELL Nylon Wire Wheel Cup Brush Set

POLIWELL Nylon Wire Wheel Cup Brush Set

POLIWELL9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 6-piece nylon abrasive set in cup, wheel and end shapes that will not spark and works wet or dry, with a stated limit of 4500 RPM.

Pros

  • Nylon abrasive will not spark and stays cool in use
  • Works wet or dry on damp bits and parts
  • Causes less surface damage than steel wire on delicate bits
  • 6 mm hex shank seats firmly in drills and impact drivers

Cons

  • Nylon cuts heavy rust slower than carbon steel wire
  • Only 6 pieces, in 3 brush shapes
  • No carbon steel brush in the set for thick scale
  • Smallest brush is the end brush, so very narrow flutes need hand work

How to Clean Rusty Drill Bits Step by Step

Start by looking the bit over in good light. Surface rust on the shank and flutes brushes off, while deep pitting on the cutting edge needs grinding back to a fresh edge and a bent shank means the bit will not cut true again. Clamp the bit or hold it firmly, fit the brush in the drill chuck, and keep your hands clear of the spinning brush. Wear eye protection and keep the bench clear, since a wire brush can throw rust and loose bristles.

Work the brush along the flutes in short passes, letting the wire do the work instead of pressing hard. A cup brush covers the broad face of a large bit, a wheel brush follows edges and seams, and a pen or end brush reaches into tight spots the wide brushes cannot. Wipe the bit with a clean rag between passes so you can see what rust is left, and keep brushing until the flutes show clean metal.

When the rust is gone, wipe the bit dry and leave it out until every trace of damp is gone. A thin coat of oil on the flutes and shank keeps new rust from forming in storage, and a dry box or rack beats a damp drawer. Bits that still show pits on the cutting edge after brushing need resharpening on a grinder or replacing, since brushing alone cannot restore a pitted edge.

Side by Side

Pick Pieces Brush shapes Wire Top speed
Holikme 12Pcs 12 Cup, wheel, pen, straight Carbon steel 4500 RPM
Romeda 5-Piece 5 Wheel, cup and brush 0.012 inch carbon steel 4500 RPM
SBGGRL 9 Pcs 9 Cup, wheel, end Carbon steel 4500 RPM
POLIWELL 6 Pack 6 Cup, wheel, end Nylon abrasive 4500 RPM

All four sets state a top speed of 4500 RPM, so the choice comes down to brush shapes and wire. Carbon steel wire cuts heavy rust faster, while nylon suits delicate bits and wet work. A set with pen and straight brushes reaches places a cup and wheel set cannot, and a set with stated wire and sizes tells you what bite to expect.

Which Brush Shape for Which Bit

Cup brushes suit broad faces and the flat of a large bit, wheel brushes trace edges and seams, and end brushes reach tight spots and detail work. The Holikme set adds pen and straight brushes for narrow recesses and fine detail, which the other sets do not offer in the same shapes. Match the brush to the spot: a wide cup on a small bit wastes time, and a small end brush on a broad face takes many passes.

For a twist bit, brush along the flutes rather than across them, so the wire follows the cutting edge instead of rounding it. On a spade or brad point bit, use the wheel brush on the flat and the end brush around the point. A bit with rust packed in the flutes needs the pen brush first, then a pass with the wheel brush to clear what is left.

The Gear for Cleaning Rusty Drill Bits

Each set below handles a step of the job, from stripping heavy rust off large bits to easing rust off small or delicate ones.

When a Bit Is Past Saving

Brushing saves a bit with surface rust, but it cannot fix a pitted cutting edge, a chipped lip, or a bent shank. If the edge stays rough or pitted after the rust is gone, the bit will grab and cut oversize, and dressing it back takes more than a brush. A bit whose shank is bent so it wobbles in the chuck, or one that shows cracks near the shank, belongs in the scrap bin. Spend the brush time on bits with sound edges and straight shanks, and resharpen or replace the rest.

For more options, see our metal fab tools guides.

FAQ for welders

Can you clean rusty drill bits with a wire brush?

Yes. A wire brush on a drill strips surface rust from the flutes and shank in short passes, and a wipe between passes shows what is left. Cup brushes cover broad faces, wheel brushes follow edges, and end brushes reach tight spots. Stop when the flutes show clean metal, then dry the bit fully.

Will a wire brush damage a drill bit?

Carbon steel wire can mark a polished face, so use a light touch and let the wire do the work. Nylon abrasive brushes cut slower but leave less surface damage, which suits delicate or coated bits. Keep the brush moving and avoid pressing hard in one spot.

What speed should you run a wire brush at?

Stay at or under the limit the maker states. All four sets in this guide state a top speed of 4500 RPM, so keep the drill at or under that limit and let the brush work without forcing it.

How do you keep drill bits from rusting again?

Dry each bit fully after cleaning, add a thin coat of oil to the flutes and shank, and store bits in a dry box or rack. Damp storage brings rust back, so keep bits out of damp drawers and wipe them down after use in wet work.

Can nylon brushes remove rust from steel drill bits?

Yes, on light rust and delicate bits, and nylon will not spark and works wet or dry. Thick scale takes more passes with nylon than with carbon steel wire, so match the brush to the rust: nylon for light rust and delicate bits, steel wire for heavy rust.

Related: best twist drill bit set, best drill bit set for metal, HSS vs cobalt drill bit, and best rust converter for auto body. Also see our what is a file card.

More buying guides