Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Cobalt vs HSS Drill Bits for Steel: Which One Should You Buy?

Cobalt vs HSS drill bits for steel: what four M35 cobalt listings claim about hardness, life and heat resistance, and when HSS is enough.

Cobalt vs HSS Drill Bits for Steel: Which One Should You Buy?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1BOSCH CO21B 21-Piece Assorted Set with Included Case CobaltBOSCH CO21B 21-Piece Assorted Set with Included Case Cobalt9.7/10View on Amazon
  2. 2DEWALT Cobalt Alloy Steel Drill Bit Set with Pilot PointDEWALT Cobalt Alloy Steel Drill Bit Set with Pilot PointView on Amazon
  3. 3IRWIN Drill Bit SetIRWIN Drill Bit SetView on Amazon
  4. 4View on Amazon
  5. 58PCS Cobalt Drill Bits Set HSSCO M35 S&D Twist Drill Bits for8PCS Cobalt Drill Bits Set HSSCO M35 S&D Twist Drill Bits forView on Amazon
  6. 65PCS M35 Cobalt Stubby Drill Bit Set for Stainless Steel &5PCS M35 Cobalt Stubby Drill Bit Set for Stainless Steel &View on Amazon
  7. 7Metric M42 8% Cobalt Twist Drill Bits Set for Stainless SteelMetric M42 8% Cobalt Twist Drill Bits Set for Stainless SteelView on Amazon

For steel, the listings in this guide say cobalt: all four sets here are M35 cobalt, and the listings claim hardness up to 67 and up to 12 times the life of an average HSS titanium coated bit, with superior heat resistance over ordinary bits. No plain-HSS set is in this group, so the HSS side is represented only by what the cobalt listings say about it. This guide compares cobalt vs HSS drill bits for steel on what the listings actually state, then ranks the four cobalt sets.

Other welders and gear to compare

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Cobalt vs HSS drill bits for steel: the short answer

M35 is high speed steel with about 5% cobalt added, per the SEDIANAS listings. The listings claim the cobalt adds hardness and heat resistance: the Sinyeenglon states hardness up to 67 and up to 12 times the life of the average HSS titanium coated bit, and the SEDIANAS states superior heat resistance and greater hardness compared to ordinary drill bits. The VALYRIANTOOL listing calls M35 HSSCO good for most general purpose applications with a combination of hardness and toughness. In these listings, HSS is the baseline that cobalt is measured against, not a separate pick.

Side by side

Cobalt (M35) HSS Listing note
Material M35: HSS with about 5% cobalt (SEDIANAS) High speed steel, no cobalt stated All four sets are M35
Hardness claim Up to 67 stated (Sinyeenglon) Average HSS titanium coated bit, per that comparison No scale stated for 67
Life claim Up to 12 times the average HSS titanium coated bit (Sinyeenglon) Baseline in that comparison Sinyeenglon comparison only
Heat resistance Superior heat resistance stated (SEDIANAS) Ordinary bits, per that comparison Compared to ordinary bits
Point angle 135-degree split point on all four sets Not stated here Split point on all four sets
Aimed at Stainless, cast iron, hardened metal (per listings) Not separated here; the M35 listing calls M35 itself good for general purpose applications Also wood and plastic in some listings

Figures are the listings’ own claims, not our measurements; always read the listing of the exact set you buy.

The four cobalt sets in this guide

Ranked by what each listing states, the Sinyeenglon 99-piece set leads: M35 cobalt from 1/16 to 3/8 inch, with 16 pieces each of the small 1/16 and 5/64 sizes, a 135-degree split point, gold oxide finish and a plastic index case. Next is the VALYRIANTOOL 8-piece set, the only one here for large holes: 9/16 to 1 inch with a 1/2-inch reduced shank and 135-degree split point. The SEDIANAS 15-piece set covers 1/16 to 3/8 inch with doubles of the three smallest sizes, and the GMTOOLS 13-piece set covers 1/16 to 1/4 inch in single pieces. All four state 135-degree split points and gold oxide finish.

When cobalt is worth it

  • Stainless and hardened steel. Every listing here aims its M35 set at stainless steel, cast iron and hardened metal; the Sinyeenglon adds titanium and zinc alloy, the VALYRIANTOOL adds copper.
  • Long runs in hard material. The claimed edge is life and heat resistance: up to 12 times the average HSS titanium coated bit per the Sinyeenglon, with cutting fluid recommended and 200 to 1000 rpm stated.
  • Big holes in steel. The VALYRIANTOOL 9/16 to 1 inch set with a 1/2-inch reduced shank is the only pick here for large-diameter work.

When HSS is enough

  • General purpose drilling. The VALYRIANTOOL listing itself calls M35 good for most general purpose applications.
  • Wood, plastic and aluminum. Three listings name wood and plastic among their uses; none of the cobalt listings claims cobalt is needed for those materials.
  • Small holes you break often. The 99-piece set includes 16 pieces each of the small 1/16 and 5/64 sizes, and the Sinyeenglon listing itself notes cobalt’s high cost.

Reading a drill bit listing

Two listings contradict themselves. Both SEDIANAS sets are titled and bulleted as M35 cobalt with 5% cobalt, but their spec tables say Material Type: High Speed Steel (HSS); we trust the titles and bullets. The VALYRIANTOOL bullets say round shanks while its spec table says 3-Flat shank; again the bullets win. Also note what is missing: no listing here states a warranty term, and the Sinyeenglon’s hardness of up to 67 states no scale.

Drilling steel safely. Clamp the work, wear eye protection, and run the speeds the listing states: the Sinyeenglon lists 200 to 1000 rpm with cutting fluid to keep the bit cool. Let the bit cut instead of leaning on it, and keep fingers clear of the chuck. See our metal fab tools hub for more shop gear.

The 135-degree split point

All four sets here state a 135-degree split point, and it is the feature that matters most on the first touch of the work. The split point is stated to center accurately and penetrate fast, which means the bit starts where you put it instead of walking across the steel. On stainless and hardened metal, the listings state the split point is self-centering to prevent walk-off. If a cobalt listing does not state a split point, that is a gap worth noticing. Every set here states one, which is part of why these four were picked.

Set size and storage

The listings here describe index storage cases with a size index for easy organizing, so the bit you need is findable in the shop. A bigger set covers more hole sizes without a second trip to the store, but every size in the case should be one you actually drill: a large set where you use only five sizes is a drawer filler. For steel work, the common sizes live in the middle of the set, and the case keeps them sorted.

FAQ for welders

Is cobalt better than HSS for steel?

Per these listings, yes for hard steel: M35 cobalt claims greater hardness and heat resistance than ordinary HSS, with up to 12 times the life of an average HSS titanium coated bit stated by the Sinyeenglon.

What does M35 mean?

M35 is high speed steel with about 5% cobalt, per the SEDIANAS listings. All four sets here are M35.

Do I need cobalt for mild steel?

The listings aim cobalt at stainless, cast iron and hardened metal. None of them claims cobalt is needed for mild steel, wood or plastic.

What point angle do these use?

All four sets state a 135-degree split point, which the listings say centers accurately and resists walking.

Why do the SEDIANAS spec tables say HSS?

Their spec tables list Material Type as High Speed Steel (HSS) while the titles and bullets say M35 cobalt with 5% cobalt. We trust the titles and bullets over the spec tables.

Related: the best hole saw for metal, hacksaw vs band saw for metal, the best die grinder for weld cleanup, wire wheel vs wire cup brush and the metal fab tools hub.

More buying guides