Carbide vs Cobalt Drill Bits: Which One Should You Buy?
Two M35 cobalt sets face off here: the Crosstar set with its coated three-flute design and the SEDIANAS set with its split-point twist design, weighed on what each listing states.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Crosstar M35 Cobalt Drill Bit Set,Three-Flute9.6/10View on Amazon - 2
29Pcs Cobalt Drill Bit Set M35 High Speed Steel9.6/10View on Amazon
Verdict. For carbide vs cobalt drill bits, the sets featured here are cobalt sets, so this comparison weighs cobalt approaches against each other and against what a carbide choice would need to state before it could claim an edge. The Crosstar set is the pick for a reader who wants a coated design with a shank made to lock in the chuck. The SEDIANAS set is the pick for a reader who wants more sizes in its box with a split point made to center on the mark.
Drilling hardened metal in a small shop usually comes down to a bench job that punishes a dull edge: stainless plate, cast iron, or a repair on a high-carbon part. This comparison looks at carbide vs cobalt drill bits through the sets featured here, and it stays close to what each listing states rather than what a catalog might promise.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
The Two Sets

Crosstar M35 Cobalt Drill Bit Set,Three-Flute
A 21-piece M35 cobalt set from 1/16 to 1/2 in, with a TiAlN coating, a three-flute design on sizes 3/32 and up, and a three-flat shank made to lock in the chuck.
Pros
- M35 cobalt steel with 5% cobalt, stated for stainless steel, hardened cast iron, high-carbon steel and titanium alloys
- TiAlN coating stated to withstand cutting temperatures up to 1472 degrees F (800 degrees C)
- Three-flute design on sizes 3/32 and up, with a maker claim of approximately 40% improved chip ejection
- Three-flat shank made to lock in the chuck under high-torque conditions
Cons
- No warranty term is stated in the listing
- Sizes from 1/16 through 7/64 use a two-flute design, not the three-flute design
- Listing recommends the set for standard depth of cut applications, with no deeper-cut claim
- 21 pieces against the SEDIANAS set at 29 pieces, so fewer sizes in the box

29Pcs Cobalt Drill Bit Set M35 High Speed Steel
A 29-piece M35 cobalt set from 1/16 to 1/2 in, with a 135 degree split point, a fully ground twist design, and a metal index storage box.
Pros
- 29 sizes from 1/16 to 1/2 in, the most sizes among the featured sets
- 135 degree split point that self-centers to prevent walk-off
- Fully ground twist design that helps clear particles and decreases friction and heat
- Metal index storage box with a size index for storage and organizing
Cons
- No warranty term is stated in the listing
- No coating is stated, unlike the Crosstar set
- No hardness figure is stated, so the listing leaves hardness unclear against the Crosstar figure
- Round straight shank with no three-flat grip claim
Other welders and gear to compare
1/8" Solid Carbide Jobber Drill Bits with Straight Shank andCheck price on Amazon
LU&MN Solid Carbide Jobber Drill BitCheck price on Amazon
Carbide Drill Bit Set : 1/16 3/16 1/8 1/4 for Hardened SteelCheck price on Amazon
1/8 Carbide Drill Bit : Max 700 Holes For Hardened &Check price on Amazon
Drill Bit Set 4 Pcs Solid Carbide Drill BitsCheck price on Amazon
Carbide vs Cobalt Drill Bits Side by Side
| Product | Gear Score | Pieces | Design |
|---|---|---|---|
| Crosstar M35 Cobalt Drill Bit Set | 9.6/10 | 21 | Three-flute on 3/32 and up, TiAlN coated, three-flat shank |
| SEDIANAS M35 Cobalt Drill Bit Set | 9.6/10 | 29 | 135 degree split point, fully ground twist, round straight shank |
Ratings in this table are the makers’ own claims taken from each product page. Neither listing states a safety standard or a warranty term.
What the Cobalt Listings State
Each featured set is an M35 cobalt high-speed steel set with 5% cobalt. The Crosstar listing states its set for stainless steel, hardened cast iron, high-carbon steel, and titanium alloys. The SEDIANAS listing states its set for stainless steel, cast iron, high temperature alloy, titanium alloy, hard plastics and woods.
A carbide set is not among the featured sets, so this article gives no carbide hardness or coating figure. A reader weighing carbide against cobalt should ask a carbide listing to state the same points these cobalt listings state: material, hardness, coating, size range, and shank. Without those stated points, a carbide claim cannot be weighed against the figures below.
Size Range and Set Size
Each set spans 1/16 to 1/2 in. The Crosstar set holds 21 pieces in that range. The SEDIANAS set holds 29 pieces in that range.
The Crosstar maker claims its set covers over 90% of common metal drilling tasks. The SEDIANAS listing names each size from 1/16 to 1/2 in, so a reader who wants fine steps between sizes gets more choice from the SEDIANAS box. A reader who wants a smaller kit to keep on the bench may prefer the Crosstar box.
Flute, Point and Shank
The Crosstar set uses a three-flute design on sizes 3/32 and up, and the maker claims approximately 40% improved chip ejection over a conventional two-flute bit, with superior hole roundness and wall finish and reduced bit walk. The Crosstar sizes from 1/16 through 7/64 use a precision two-flute design for delicate work, so the three-flute claim does not cover the smallest sizes. The listing note overlaps at 3/32, which falls in both ranges, so the flute design at that size is left unclear by the listing.
The SEDIANAS set uses a 135 degree split point with a round straight shank, and the listing says the point self-centers to prevent walk-off. The SEDIANAS set uses a fully ground twist design that helps clear particles and decreases friction and heat for cooler drilling performance.
The Crosstar set uses a three-flat shank that the listing says ensures a complete lock in the drill chuck and eliminates spin-out under high-torque conditions from impact drivers and heavy-duty drills. The SEDIANAS listing states a round straight shank and makes no flat-grip claim, so a reader who worries about spin-out has a stated reason to favor the Crosstar shank.
Heat and Hardness
The Crosstar listing states a Titanium Aluminum Nitride (TiAlN) nano-coating that withstands cutting temperatures up to 1472 degrees F (800 degrees C), and it states effective drilling hardness up to 60 HRC. The SEDIANAS listing states superior heat resistance and cooler drilling performance in words, with no temperature figure and no hardness figure.
That gap leaves the heat and hardness comparison one-sided. The Crosstar figures can be quoted because the listing states them. The SEDIANAS listing leaves its own heat and hardness figures unclear, so this article does not rank the SEDIANAS set on heat or hardness against the Crosstar figures.
Choose the Crosstar Set If
- A coated three-flute design matters to the work, with the small sizes understood as two-flute.
- A stated hardness figure matters, and up to 60 HRC fits the hardened metal on the bench.
- A three-flat shank that locks in the chuck matters under high-torque conditions.
- An index storage case for 21 pieces fits the bench kit.
Choose the SEDIANAS Set If
- More sizes matter, with 29 pieces from 1/16 to 1/2 in.
- A 135 degree split point that self-centers matters for starting holes on the mark.
- A fully ground twist design for chip clearing matters.
- A metal index storage box with a size index matters for keeping sizes in order.
How the Sets Were Scored
Each set is scored on performance, build, value, safety and warranty. The site method page explains the weights.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Crosstar M35 Cobalt Drill Bit Set | 9.6 | 30 | 21 | 20 | n/a | 0 |
| SEDIANAS M35 Cobalt Drill Bit Set | 9.6 | 28 | 20 | 21 | n/a | 0 |
The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure. Safety points apply to gear that runs on power or lists safety features. Without either, we score out of 90 instead of 100.
Before You Strike an Arc
- For the Crosstar set, seat the three-flat shank fully in the chuck so it locks before drilling.
- For the SEDIANAS set, check that the round straight shank seats true in the chuck, since the listing states a round straight shank with no flat.
- Match the bit size to the hole from the index case or box, and keep the small sizes apart, since the Crosstar sizes from 1/16 through 7/64 use a two-flute design.
- Keep to standard depth of cut work with the Crosstar set, since the listing recommends it for standard depth of cut applications.
- Clear chips often and let the bit cool, since the SEDIANAS listing points to chip clearing and cooler drilling performance.
FAQ for welders
Which drill bit material suits stainless steel work?
Each featured cobalt set states stainless steel among its uses, so the cobalt side is documented here for that work. The Crosstar listing states effective drilling hardness up to 60 HRC. No carbide set is featured here, so this article states no carbide figure for stainless steel work.
What does the Crosstar three-flute design change?
The maker claims superior hole roundness and wall finish, approximately 40% improved chip ejection, and reduced bit walk over a conventional two-flute bit. The claim covers sizes 3/32 and up. Sizes from 1/16 through 7/64 use a precision two-flute design for delicate work.
How many sizes come in each set?
The Crosstar set holds 21 pieces from 1/16 to 1/2 in. The SEDIANAS set holds 29 pieces from 1/16 to 1/2 in. The size range matches, and the SEDIANAS box holds more steps between sizes.
Do either of these sets state a warranty term?
Neither listing states a warranty term, so the warranty field is left empty for each set. A reader who wants a written warranty term should ask the seller to state one before buying. The absence of a term is not a promise of cover.
Which set suits a reader who wants the most sizes?
The SEDIANAS set suits that reader, with 29 pieces from 1/16 to 1/2 in against 21 pieces in the Crosstar set. The Crosstar set suits a reader who values the coated three-flute design and the three-flat shank over extra sizes.
Related: best cobalt drill bit set, best drill bits for steel, cobalt vs HSS drill bits for steel, and the metal fab tools hub.




