Best Step Drill Bit for Auto Body (2026): 5 Bits Compared
Five step drill bits for auto body panels compared by size range, flute design, coating and shank, from a 10-step TiN bit to a 2 inch unibit.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallNEIKO 10174A Step Bit9.5/10View on Amazon - 2
Best PairBosch IMSDC002 Step Bit Set9.5/10View on Amazon - 3
Largest HolesJerax 1/4 to 2 in Step Bit9.4/10View on Amazon - 4
Best Small SetLOOTOOLS 3pc Step Bit Set9.3/10View on Amazon
Auto body work asks a drill bit to do something rude: punch a clean, round hole through thin painted steel without grabbing, tearing the edge or wandering off the mark. A twist bit skates and snags on sheet metal. A step bit walks up in stages, shaving the hole wider one ledge at a time, and leaves an edge that needs little more than a touch to finish.
This roundup compares the best step drill bit for auto body across five listings: four single bits and sets in high speed steel, with titanium coatings, spiral and straight flutes, and size ranges that run from small trim holes to a full two inches. Each is scored on the sizes, steel and shank its listing actually states.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall NEIKO 10174A Step Bit: 10 steps from 1/4 to 1-3/8 in, TiN coated HSS, spiral flutes, hex shank. Check price on Amazon
- Best Pair Bosch IMSDC002 Step Bit Set: Two Swiss-made impact-ready bits covering 3/16 to 1-1/8 in holes. Check price on Amazon
- Largest Holes Jerax 1/4 to 2 in Step Bit: 10 sizes up to 2 in for firewall and conduit holes, straight flutes. Check price on Amazon
- Best Small Set LOOTOOLS 3pc Step Bit Set: Three Ti coated bits for holes from 3/16 to 1/2 in, hex shanks. Check price on Amazon
The machines

NEIKO 10174A Step Drill Bit
A 10-step bit in #4241 HSS with a titanium nitride coating, spiral flutes and a 1/4 in hex shank, covering holes from 1/4 to 1-3/8 in.
Pros
- 10 stated sizes on one bit: 1/4, 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1-1/8, 1-1/4 and 1-3/8 in
- 135-degree split-point tip stated to prevent walking from the center line
- Two-flute spiral design stated to deburr as it expands the hole
- 1/4 in hex shank snaps into quick change chucks and impact drivers
Cons
- Set name in the table says 10-Piece for a single bit with 10 steps
- Item weight is listed as 0.27 g, which cannot be right for a steel bit
- No warranty term is stated

BOSCH IMSDC002 2 pc. High-Speed Steel Impact Tough
A two-piece Swiss-made HSS step bit set for cordless drills and impact drivers, covering 3/16 to 7/8 in and 1/4 to 1-1/8 in.
Pros
- Two bits split the range: 3/16 to 7/8 in and 1/4 to 1-1/8 in
- Hex shank, impact-ready and drill/driver compatible
- Balanced double flute stated to eliminate chatter and vibration
- Swiss engineered and manufactured, per the listing
Cons
- Durability figures (2X cutting edges, 2X life, 2X holes per charge) are maker claims with no stated basis
- Individual step sizes are not enumerated, only the two ranges
- No warranty term is stated

1/4" - 2" HSS Step Drill Bit Unibit for Hole
A large HSS unibit with 10 marked sizes from 1/4 to 2 in, double straight flutes and a self-starting split point, for sheet metal and softer metals.
Pros
- Widest range here: 10 sizes from 1/4 in up to a full 2 in
- Self-starting, non-walking split point: no pilot hole required, per the listing
- Polished steps with size highlights readable during drilling
- Stated for iron, aluminum, copper, plastic and wood
Cons
- Straight flutes, where the spiral listings claim smoother cutting and better chip clearing
- Uncoated HSS, the plainest finish in this group
- Table calls the point a brad point against the bullets' split point, and lists a 2 in minimum bore
- Brand is spelled Jearx once in its own listing text

3 PCS Step Drill Bit Set
A three-piece set of titanium coated HSS step bits with 1/4 in hex shanks, covering holes from 3/16 to 1/2 in.
Pros
- Three bits in the set for the small-hole range
- Titanium coated, heat-treated HSS per the bullets
- 1/4 in hex shanks fit drills, impact drivers and electric screwdrivers
- Precision ground spiral flutes stated for clean holes without burring
Cons
- Range stops at 1/2 in, the smallest ceiling in this group
- Each bit's own size steps are not itemized in the listing
- Spec table recommends aluminum only, narrower than the bullets' material list
- No warranty term is stated

Milwaukee Electric Tool 48-89-9209 Electric Step
A single HSS step bit with a black oxide finish and a 3-flat round shank, sold as the No 9, with no size range stated in the listing.
Pros
- 3-flat secure grip shank stated to reduce slippage
- Black oxide finish on high speed steel
- Spiral flute design per the spec table
- A known tool brand's step bit line
Cons
- No size range or step count is stated anywhere in the listing
- Bullets are boilerplate: no sizes, coating or point details
- Round shank only: no hex for quick change chucks
- No warranty term is stated
Other welders and gear to compare
MilwaukeeCheck price on Amazon
TEMO M35 Cobalt Spiral Step Drill Unibit Bit 1/4"-3/4" 9 SizeCheck price on Amazon
NEIKO 10185A Step Drill BitCheck price on Amazon
NEIKO 10194A Step Drill BitCheck price on Amazon
NEIKO 10182A Titanium Step Drill BitCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Steps | Size range | Material / finish | Shank | Flutes | Warranty |
|---|---|---|---|---|---|---|---|
| NEIKO 10174A Step Bit | 9.5/10 | 10 | 1/4 to 1-3/8 in | HSS, titanium nitride | 1/4 in hex | 2, spiral | Not stated |
| Bosch IMSDC002 Step Bit Set | 9.5/10 | 2 bits | 3/16 to 1-1/8 in | HSS | Hex | 2, double | Not stated |
| Jerax 1/4 to 2 in Step Bit | 9.4/10 | 10 | 1/4 to 2 in | HSS, uncoated | Straight | 2, straight | Not stated |
| LOOTOOLS 3pc Step Bit Set | 9.3/10 | 3 bits | 3/16 to 1/2 in | HSS, titanium | 1/4 in hex | 2, spiral | Not stated |
| Milwaukee No 9 Step Bit | 9.2/10 | Not stated | Not stated | HSS, black oxide | Round with flats | 2, spiral | Not stated |
Treat the specs as maker ratings pulled straight from the listings; we gathered them on 21 October 2026. None of the five listings states a warranty term.
Buying guide: choosing the best step drill bit for auto body
Size range: match the holes you actually drill
Body work is mostly small and medium holes: trim clips, fasteners, antenna and sensor holes, and access holes in inner panels. The NEIKO covers that ground in one bit, 1/4 to 1-3/8 in across 10 steps. The Bosch pair splits it across two bits, 3/16 to 7/8 in and 1/4 to 1-1/8 in. The Jerax runs to a full 2 in, which is conduit and firewall territory more than panel work, and the LOOTOOLS set stops at 1/2 in, so it covers only the small end. The Milwaukee listing states no range at all, which leaves its coverage unverifiable from the page.
Spiral or straight flutes
Three of these bits are spiral fluted (NEIKO, LOOTOOLS and the Milwaukee) and two are straight fluted (Jerax, and the Bosch per its table). The NEIKO listing makes the spiral case directly: its two-flute spiral design is stated to cut smoother with less chatter, pull chips up and out, run cooler and deburr as it expands the hole. The Jerax counters with polished steps and printed size highlights so the target size can be read mid-drilling. For thin body panels, the chatter and chip claims are the ones that matter.
Shank: hex for drivers, round for chucks
The NEIKO and LOOTOOLS bits and the Bosch set use 1/4 in hex shanks that snap into quick change chucks and impact drivers, which suits the cordless workflow of a body shop bay. The Jerax uses a straight shank and the Milwaukee a round shank with three flats, which the listing says reduces slippage in a standard chuck. Neither is wrong; match the bit to the driver you already reach for.
Steel and coatings
All five are high speed steel. The NEIKO adds a titanium nitride coating and names its steel grade, #4241 HSS; the LOOTOOLS bits are titanium coated and heat treated per their bullets. The Bosch bits are uncoated HSS with the maker’s 2X life claims stated as claims. The Milwaukee wears black oxide. On painted panels the coating story matters less than the point: the NEIKO and Jerax both state split-point, self-starting tips that resist walking across a finished surface.
FAQ for welders
Can a step bit drill auto body panels without tearing them?
That is the job the design suits: each step shaves the hole wider in a shallow cut instead of augering through, and the NEIKO listing states its spiral flutes automatically deburr while expanding the hole. Thin panels still need support behind them and a light feed, whatever the bit.
Do step bits need a pilot hole?
Two listings say no for their bits: the Jerax states a self-starting, non-walking split point tip that needs no pilot hole, and the NEIKO states a 135-degree split-point tip that prevents walking away from the center line. The other listings make no pilot claim.
Step bit or hole saw for large holes?
The Jerax reaches 2 in, the top of step bit territory in this group, and drills its 10 sizes with one bit and no changes. Past the stated ranges here, a hole saw is the tool; our hole saw for metal picks cover that side.
How many sizes should one bit cover?
Count the marked steps, not the marketing. The NEIKO and Jerax each state 10 sizes on one bit; the Bosch set spreads its range over two bits, and the LOOTOOLS set over three smaller ones. For panel work, one bit that spans 1/4 to 1-3/8 in, the NEIKO pattern, means the fewest changes mid-job.
Do any of these bits carry a warranty?
None of the five listings states a warranty term. The Bosch listing makes durability claims (2X longer life, as the maker’s claim) but states no term, and the others are silent as well.
Related: our best drill bits for steel, the best hole saw for metal and the best deburring tool for steel.
Scoring, line by line
Each bit is scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. Step bits carry no safety listing to state and none of these listings states a warranty, so those two criteria score zero throughout; the ranking comes from stated sizes, steel, coatings and shanks.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| NEIKO 10174A Step Bit | 9.5 | 30 | 21 | 21 | 0 | 0 |
| Bosch IMSDC002 Step Bit Set | 9.5 | 29 | 22 | 20 | 0 | 0 |
| Jerax 1/4 to 2 in Step Bit | 9.4 | 28 | 19 | 21 | 0 | 0 |
| LOOTOOLS 3pc Step Bit Set | 9.3 | 23 | 18 | 21 | 0 | 0 |
| Milwaukee No 9 Step Bit | 9.2 | 20 | 19 | 16 | 0 | 0 |
Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score.




