Best Cutting Fluid for Steel (2026): 4 Picks for Drilling, Tapping and Sawing
Four cutting fluids for steel, compared on form, size, metals covered, dilution and the warranty each listing states.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallTap Magic EP-Extra Cutting Oil9.7/10View on Amazon - 2
Best for Annular CuttersJancy Slugger Cutting Fluid9.6/10View on Amazon - 3
Best Gallon SizeAnchorlube All-Purpose Metalworking Compound9.6/10View on Amazon - 4
Best Spout BottleJD Commercial Cutting Fluid9.6/10View on Amazon
Cutting steel without fluid wears the edge fast and leaves a rough hole, so the best cutting fluid for steel keeps the cut cool and the tool turning through drilling, tapping and sawing. This guide compares the fluids on what each listing states: form, size, the metals covered, dilution and warranty, so you can match the bottle to the job.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall Tap Magic EP-Extra Cutting Oil: Works on all steels plus aluminum, titanium, nickel, cast iron, brass and inconel, for drilling, tapping, milling and more, in two 16 oz squeeze bottles. Check price on Amazon
- Best for Annular Cutters Jancy Slugger Cutting Fluid: Water-based fluid for galvanized, steel, aluminum, brass and copper, with a stated 8:1 dilution ratio and a 1 quart size. Check price on Amazon
- Best Gallon Size Anchorlube All-Purpose Metalworking Compound: A water-based, 1 gallon jug for drilling, tapping and sawing, great on stainless steel, with no oil in the mix. Check price on Amazon
- Best Spout Bottle JD Commercial Cutting Fluid: A 16 oz bottle with a yorker-style spout and twist cap, for drilling, milling and threading all metals. Check price on Amazon
The machines

Tap Magic Cutting Fluid, 2 Pack
An EP cutting oil in two 16 oz squeeze bottles, for drilling, tapping, milling and more on all steels and a long list of other metals, from a maker in the trade since 1953.
Pros
- Works on all steels plus aluminum, titanium, nickel, cast iron, brass and inconel
- Covers drilling, tapping, milling, boring, reaming, turning, threading, engraving and sawing
- Two 16 oz squeeze bottles put the oil where the cut happens
- A maker in the trade since 1953
Cons
- Oil-based, so wipe the work after cutting
- Two 16 oz bottles hold less fluid than the 1 gallon jug here
- No dilution ratio is stated
- No warranty term in the listing

Slugger by Fein Cutting Fluid, Water-Based
A water-based fluid in a 1 quart bottle, for galvanized, steel, aluminum, brass and copper, with a stated 8:1 dilution ratio that stretches the bottle.
Pros
- Stated 8:1 dilution ratio with water
- Lists galvanized, steel, aluminum, brass, copper and alloys
- Maker says it extends cutter life and cuts heat and friction
- 1 quart bottle at 2.0 lb, easy to carry to the drill press
Cons
- Only 1 quart in the bottle
- Needs mixing at 8:1 before use
- No size larger than 1 quart is listed
- No warranty term in the listing

Anchorlube All-Purpose Metalworking Compound 1
A water-based, all-purpose metalworking compound in a 1 gallon jug, for drilling, tapping and sawing, great on stainless steel, with no oil in the mix.
Pros
- A 1 gallon jug for a busy shop
- Water-based with no oil, and non-hazardous
- Great on stainless steel, per the maker
- Maker says it gives a fast, smooth cut even on exotic metals
Cons
- No weight in the listing
- No dilution ratio is stated
- A gallon jug takes more shelf space than a 16 oz bottle
- No applicator is listed, so you supply your own brush or bottle

JD Commercial Cutting Fluid 16 OZ, Cutting
A 16 oz cutting fluid for drilling, milling and threading all metals, with anti-wear and anti-rust properties, in a bottle with a yorker-style spout and twist cap.
Pros
- Lists all metals, for drilling, milling and threading
- Anti-wear and anti-rust properties, per the maker
- Yorker-style spout puts fluid at the cut
- Twist cap for storage between jobs
Cons
- Only 16 oz in the bottle
- No dilution ratio is stated
- Sold as a single bottle, with no multi-pack listed
- No warranty term in the listing
Other welders and gear to compare
Slugger by Fein Cutting FluidCheck price on Amazon
Forney 20857 Tap Magic Industrial Pro Cutting FluidCheck price on Amazon
Tap Magic 30004P ProTap Cutting FluidCheck price on Amazon
TapMagic 16 oz. Can New Improved Cutting Fluid Brand: TapCheck price on Amazon
Rapid Tap Heavy Duty Cutting Fluid 4 Ounce Brand: ReltonCheck price on Amazon
Hot Max 27050 Tap Magic Cutting FluidCheck price on Amazon
Spec sheet comparison
| Product | Gear Score | Form | Size | Metals | Dilution |
|---|---|---|---|---|---|
| Tap Magic EP-Extra Cutting Oil | 9.7/10 | EP oil | 2 x 16 oz | All steels, aluminum, brass | Not stated |
| Jancy Slugger Cutting Fluid | 9.6/10 | Water-based | 1 quart | Steel, aluminum, brass, copper | 8:1 |
| Anchorlube All-Purpose Metalworking Compound | 9.6/10 | Water-based | 1 gallon | Steel, stainless steel | Not stated |
| JD Commercial Cutting Fluid | 9.6/10 | Cutting fluid | 16 oz | All metals | Not stated |
These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 19 November 2026.
How to choose the best cutting fluid for steel
Water-based or oil
Two fluids here are water-based: the Anchorlube gallon and the Jancy quart. Tap Magic is an EP cutting oil, and the JD fluid lists no base. A water-based fluid suits a shop that wants no oil in the mix, while an EP oil suits cuts where the edge runs hot.
Dilution
Only the Jancy fluid states a dilution ratio: 8:1 with water, which stretches a quart across many cuts. The other three list no ratio, so check the label on the bottle you buy.
Metals covered
Tap Magic lists all steels plus aluminum, titanium, nickel, cast iron, brass and inconel. Jancy lists galvanized, steel, aluminum, brass, copper and alloys. Anchorlube is great on stainless steel, per the maker, and JD Commercial lists all metals. Match the fluid to the metal in the job.
Size and pack
Sizes here run from a 16 oz bottle to a 1 gallon jug. Tap Magic ships as two 16 oz squeeze bottles, the JD fluid as a single 16 oz bottle, the Jancy fluid as a 1 quart bottle, and the Anchorlube as a 1 gallon jug. A gallon suits a busy shop, while a 16 oz bottle suits a bench drawer.
Use as directed. Wear eye protection when drilling, tapping or sawing, and keep chips clear of the cut. Wipe up spills so the floor stays dry, and keep oil-based fluid away from open flame. Follow the maker label on the bottle, and see the OSHA welding overview and our Safety Disclaimer.
Before You Strike an Arc
- Check the bottle cap and seal on arrival, and confirm the fluid matches the metal in the job.
- Check the dilution on the label before mixing; the Jancy fluid lists an 8:1 water ratio.
- Check the applicator: squeeze bottles and the yorker spout on the JD bottle put fluid where the cut happens.
- Keep chips clear of the cut and the fluid off the bench edge before you start.
FAQ for welders
Can I use cutting fluid on stainless steel?
Yes. Anchorlube is great on stainless steel, per the maker, and Tap Magic works on all steels, which covers stainless. Match the fluid to the job, and keep the cut fed with fluid while the tool turns.
Do I need to dilute cutting fluid with water?
Only the Jancy fluid here states a dilution ratio, 8:1 with water. The other three list no ratio, so use them as the label directs. Mix the Jancy fluid in a separate container before it reaches the cut.
What size cutting fluid should I buy?
Sizes here run from a 16 oz bottle to a 1 gallon jug. A gallon suits a shop that cuts steel every day, while a 16 oz bottle suits a bench drawer or occasional jobs. Tap Magic ships as two 16 oz squeeze bottles, which split the supply across the bench and the tool bag.
Does cutting fluid extend tool life?
Three makers here state it directly: Anchorlube prolongs tool life, Jancy extends cutter life, and JD Commercial extends tool and tap life. Tap Magic lists drilling, tapping and milling among its operations. Fluid cools the cut and cuts friction, which is what wears an edge.
Does cutting fluid work on aluminum and brass?
Yes. Jancy lists aluminum and brass among its metals, and Tap Magic lists aluminum and brass too. JD Commercial lists all metals, which covers both. Anchorlube is listed for drilling, tapping and sawing, with stainless steel called out by the maker.
Related: best cutting oil for drilling metal, best tapping fluid, cutting oil vs tapping fluid, best drill bits for steel, best drill bits for drilling stainless steel, best annular cutter for magnetic drill, and annular cutter vs twist drill bit.
Scoring, line by line
Each fluid is scored on performance, build, value, safety and warranty, with the weights published on our How We Pick page. No listing here states a safety certification, so the ranking comes from performance, build and value.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Tap Magic EP-Extra Cutting Oil | 9.7 | 32 | 21 | 21 | n/a | 0 |
| Jancy Slugger Cutting Fluid | 9.6 | 30 | 21 | 20 | n/a | 0 |
| Anchorlube All-Purpose Metalworking Compound | 9.6 | 29 | 20 | 21 | n/a | 0 |
| JD Commercial Cutting Fluid | 9.6 | 28 | 20 | 20 | n/a | 0 |
Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score. Unpowered items with no stated safety features skip the safety line, and their score comes from the 90 points that are left.




