Best Annular Cutter for Magnetic Drill (2026)
Annular cutters and sets for a magnetic drill, compared on diameter range, cutting depth, shank fit and kit contents.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallS&F STEAD & FAST 13 Pc Set9.6/10View on Amazon - 2
Largest SetANGELSWORD 14 Pc Set9.6/10View on Amazon - 3
Compact SetPro Edge 6 Pc Set9.6/10View on Amazon - 4
Deepest Single CutterHARFINGTON 27/64 Inch Cutter9.5/10View on Amazon
A magnetic drill earns its keep when a hole lands clean in plate, on a frame rail or in a beam flange, without wandering or tearing the edge. Choosing the best annular cutter for magnetic drill work comes down to diameter, cutting depth, shank fit and what the kit actually includes, as stated on each listing.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall S&F STEAD & FAST 13 Pc Set: A 13 pc set covering 7/16 inch to 1-1/16 inch, with a 1 inch depth, a 3/4 inch Weldon shank and a carrying case. Check price on Amazon
- Largest Set ANGELSWORD 14 Pc Set: A 14 pc set covering 7/16 inch to 1-1/16 inch, with a 1 inch depth and an aluminum case. Check price on Amazon
- Compact Set Pro Edge 6 Pc Set: A 6 pc set covering 1/2 inch to 1-1/16 inch, with a 1 inch depth and 2 pilot pins. Check price on Amazon
- Deepest Single Cutter HARFINGTON 27/64 Inch Cutter: A 27/64 inch cutter with a 2 inch cutting depth and a 3/4 inch shank. Check price on Amazon
The machines

S&F STEAD & FAST Annular Cutter Set 13 Pcs
A 13 pc set covering 7/16 inch to 1-1/16 inch, with a 1 inch cutting depth, a 3/4 inch Weldon shank and a carrying case.
Pros
- 11 diameters from 7/16 inch to 1-1/16 inch in a set
- M2AL high speed steel, stated for durability, wear resistance and heat resistance
- 3/4 inch Weldon shank with 2 flats for firm clamping
- Kit includes 2 pilot pins, 1 hex wrench and a carrying case
Cons
- Title count and kit list do not line up when the wrench is counted
- Drill press use needs an additional arbor, not included in the set
- Annular bits are for drilling in a layer at a time only, per the caution in the listing
- No warranty term is stated in the listing

ANGELSWORD M2 HSS Annular Cutter Set 14
A 14 pc set covering 7/16 inch to 1-1/16 inch, with a 1 inch cutting depth, M2 high speed steel at 62-65 HRC and an aluminum case.
Pros
- 14 pc set with diameters from 7/16 inch to 1-1/16 inch
- M2 high speed steel at 62-65 HRC, stated for wear resistance and clean smooth cuts
- 3/4 inch Weldon shank with a pilot pin included
- Aluminum case for carrying the set
Cons
- Listing does not name the pilot pin count or a hex wrench
- No brand compatibility list is stated in the listing
- No warranty term is stated in the listing

6pcs Annular Cutter Set 1" Cutting Depth 1/2"
A 6 pc set covering 1/2 inch to 1-1/16 inch, with a 1 inch cutting depth, M2 high speed steel at 62-65 HRC and 2 pilot pins.
Pros
- 6 commonly used sizes from 1/2 inch to 1-1/16 inch
- M2 high speed steel at 62-65 HRC, stated for hardness, toughness and wear resistance
- Weldon shank stated to reduce vibration and deviation during cutting
- Includes 2 pilot pins at 6.35 mm by 77 mm and 1 hex wrench at 1/4 inch
Cons
- Range stops at 1/2 inch, so smaller diameters in the wider sets are absent
- No carrying case is named in the listing
- Metal list is limited to steel, aluminum and copper in the listing
- No warranty term is stated in the listing

SALI 2 pcs Annular Cutter Diameter 7/8 Inch
A 7/8 inch annular cutter with a 1 inch cutting depth, a 3/4 inch Weldon shank, a 1/4 inch by 3 inch pilot pin and a plastic case.
Pros
- M20AL high speed steel, stated for durability, wear resistance, high efficiency and superior service life
- CNC-machined cutter stated for smooth, reamed, burr-free edges
- Plastic case holding a cutter and a pilot pin
- Compatibility list names Alfra, BDS, Dewalt, Euroboor, Hougen and Ruko
Cons
- Drill press use needs an extra arbor, not included in the pack
- Diameter choice is limited to 7/8 inch in this listing
- No warranty term is stated in the listing

HARFINGTON Annular Cutter 27/64" Cutting Diameter
A 27/64 inch annular cutter with a 2 inch cutting depth, a 3/4 inch shank and a locating pin, for plate or pipe work.
Pros
- 2 inch cutting depth, deeper than the 1 inch depth stated for the sets here
- M2 high speed steel, stated for durability, wear resistance, efficiency and long service life
- Shank with 4 flat faces for firm clamping
- Metal list covers mild steel, structural steel, cast iron, stainless steel, aluminum and copper, in plate or pipe form
Cons
- Diameter is limited to 27/64 inch, with no range in the listing
- Title wording around depth and locating pin is unclear; bullets give the clearer figures
- Package lists a cutter and a locating pin, with no spare pin named
- No warranty term is stated in the listing
Other welders and gear to compare
SALI 4 pcs Annular Cutter Diameter 5/8 Inch with Weldon ShankCheck price on Amazon
SALI 2 pcs Annular Cutter Diameter 11/16 Inch with WeldonCheck price on Amazon
SALI 2 pcs Annular Cutter Diameter 5/8 Inch with Weldon ShankCheck price on Amazon
SALI 2 pcs Annular Cutter Diameter 7/16 Inch with WeldonCheck price on Amazon
SALI Annular Cutter Diameter 1-1/4 Inch with Weldon Shank 3/4"Check price on Amazon
Spec sheet comparison
| Model | Gear Score | Diameter | Cutting depth | Shank | Kit |
|---|---|---|---|---|---|
| S&F STEAD & FAST 13 Pc Set | 9.6/10 | 7/16 inch to 1-1/16 inch | 1 inch | 3/4 inch Weldon | 11 cutters, 2 pilot pins, 1 hex wrench, carrying case |
| ANGELSWORD 14 Pc Set | 9.6/10 | 7/16 inch to 1-1/16 inch | 1 inch | 3/4 inch Weldon | 14 pc set, pilot pin, aluminum case |
| Pro Edge 6 Pc Set | 9.6/10 | 1/2 inch to 1-1/16 inch | 1 inch | Weldon shank | 6 cutters, 2 pilot pins, 1 hex wrench |
| SALI 7/8 Inch Cutter | 9.5/10 | 7/8 inch | 1 inch | 3/4 inch Weldon | Cutter, pilot pin, plastic case |
| HARFINGTON 27/64 Inch Cutter | 9.5/10 | 27/64 inch | 2 inch | 3/4 inch shank | Cutter, locating pin |
All specs here repeat what the maker rates and the listing prints, copied down 2 November 2026.
Buying guide: the best annular cutter for magnetic drill
Diameter range
Diameter range decides whether a set covers the holes a shop drills often. The S&F set and the ANGELSWORD set cover 7/16 inch to 1-1/16 inch, while the Pro Edge set covers 1/2 inch to 1-1/16 inch. The SALI cutter covers 7/8 inch, and the HARFINGTON cutter covers 27/64 inch, so those cutters suit a narrow hole size rather than a range of sizes. Match the diameter on the listing to the hole size on the job, and do not assume a set includes a diameter outside its stated range.
Cutting depth
Cutting depth decides how thick a plate a cutter can pass through in a pass. The sets here and the SALI cutter state a 1 inch cutting depth, while the HARFINGTON cutter states a 2 inch cutting depth. A deeper cutter does not replace a wider set, and a shallow depth does not suit thick plate work. Compare depth alongside diameter, since a cutter that fits the hole size may still fall short on depth for the plate on the bench.
Shank fit and pilot pin
Shank fit decides whether a cutter clamps firmly in the drill. The listings here state a 3/4 inch Weldon shank for the S&F set, the ANGELSWORD set, the SALI cutter and the HARFINGTON cutter, while the Pro Edge listing names a Weldon shank without stating a shank size. Pilot pins are named for the SALI cutter at 1/4 inch by 3 inch, for the Pro Edge set at 6.35 mm by 77 mm, and for the HARFINGTON cutter as a locating pin at 102 mm by 4.02 inch and 5 mm by 0.2 inch. Confirm the shank and the pin on the listing before ordering, since a missing pin or a mismatched shank stalls the job.
Kit contents and carrying case
Kit contents decide how much of the job can be done from the case as delivered. The S&F set lists 11 cutters, 2 pilot pins, 1 hex wrench and a carrying case. The ANGELSWORD set is a 14 pc set with a pilot pin and an aluminum case. The Pro Edge set lists 6 cutters, 2 pilot pins and 1 hex wrench, with no case named in the listing. The SALI pack lists a cutter and a pilot pin in a plastic case, and the HARFINGTON package lists a cutter and a locating pin, with no case named. Count the kit from the bullets, not from the title alone, since title counts and kit lists can differ.
Fit checks before drilling
Fit checks matter because annular cutters remove only the edge of the hole, leaving a slug in the middle, and the listing for the S&F set warns that annular bits are for drilling in a layer at a time only. Hold the workpiece firmly, start with a low feed rate, and increase the feed rate once the cutter is 2-3 mm into the material, as that listing directs. For drill press use, the SALI listing and the S&F listing state that an extra arbor is needed, and that the arbor is not included. Wear safety glasses, gloves and protective clothing, as the Pro Edge listing directs, and keep hands and other body parts away from the working tool while it is in operation.
Before You Strike an Arc
- Confirm the shank on the listing matches the magnetic drill on the bench, and confirm the pilot pin is named in the kit.
- Hold the workpiece firmly before starting, and start with a low feed rate until the cutter is into the material.
- Wear safety glasses, gloves and protective clothing, and keep hands away from the working tool while it is in operation.
- Confirm whether drill press use needs an extra arbor, since the listings that mention an arbor state that it is not included.
- Check the kit contents on arrival against the bullets, including the case, pins and wrench where the listing names them.
FAQ for welders
What diameter range do these annular cutter sets cover?
The S&F set and the ANGELSWORD set cover 7/16 inch to 1-1/16 inch, and the Pro Edge set covers 1/2 inch to 1-1/16 inch. The SALI cutter covers 7/8 inch, and the HARFINGTON cutter covers 27/64 inch. Choose a set for a range of hole sizes, and choose a cutter on its own for a narrow hole size that matches the listing.
Can a cutter from this list be used on a drill press?
The SALI listing and the S&F listing state that drill press use needs an extra annular cutter arbor, and that the arbor is not included in the pack or the set. The other listings here do not state drill press use, so do not assume an arbor is included or that drill press use is covered. Confirm the arbor need on the listing for the cutter being ordered.
What shank do these cutters state?
The S&F set, the ANGELSWORD set, the SALI cutter and the HARFINGTON cutter all state a 3/4 inch Weldon shank, with flats named for firm clamping on the S&F set, the SALI cutter and the HARFINGTON cutter. The Pro Edge listing names a Weldon shank without stating a shank size. Compatibility brand lists differ by listing, so match the shank and the brand list to the drill on the bench.
How deep can these cutters cut?
The sets here and the SALI cutter state a 1 inch cutting depth. The HARFINGTON cutter states a 2 inch cutting depth, with a length of 83 mm by 3.27 inch and a locating pin of 102 mm by 4.02 inch and 5 mm by 0.2 inch. Compare depth with diameter and plate thickness, since depth alone does not decide whether a cutter suits a job.
What should be checked on arrival?
Check the cutter diameter, the pilot pin or locating pin, and the case and wrench where the listing names them. For the SALI cutter, check the flat count, since the title says 2 flats while the bullets say 20 flats. For the ANGELSWORD set, check the piece count, since the spec table lists NumberOfItems as 1 against a 14 pc title. For the S&F set, count the kit from the bullets, since the title count and the kit list do not line up when the wrench is counted.
Related: annular cutter vs twist drill bit, magnetic drill vs hand drill, annular cutter vs hole saw, magnetic drill vs benchtop drill press.
Scoring, line by line
Each cutter is scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. Annular cutters have no electrical safety listing stated here, and no warranty term is stated for any pick here, so every cutter here scores zero on those criteria; the ranking comes from performance, build and value.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| S&F STEAD & FAST 13 Pc Set | 9.6 | 30 | 21 | 21 | n/a | 0 |
| ANGELSWORD 14 Pc Set | 9.6 | 29 | 21 | 20 | n/a | 0 |
| Pro Edge 6 Pc Set | 9.6 | 28 | 20 | 21 | n/a | 0 |
| SALI 7/8 Inch Cutter | 9.5 | 27 | 20 | 19 | n/a | 0 |
| HARFINGTON 27/64 Inch Cutter | 9.5 | 26 | 20 | 18 | n/a | 0 |
A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number. Unpowered items with no stated safety features skip the safety line, and their score comes from the 90 points that are left.




