Best Annular Cutter Set (2026): 5 Picks for a Magnetic Drill
Five annular cutter sets for a magnetic drill, compared on cutting depth, diameter range, shank fit, pilot pins and case.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallKEENTECH 14-PC9.7/10View on Amazon - 2
Most Sizes at 2-Inch DepthS&F 13-Pc9.7/10View on Amazon - 3
Largest DiametersS&F 6-Pc9.6/10View on Amazon - 4
Hardened HSS 65 HRCZELCAN 11-Pc9.6/10View on Amazon
A mag drill earns its keep when a plate needs a clean, round hole and a twist bit would wander, chatter and take all morning. The best annular cutter set for that job cuts only the rim of the hole, leaves the center behind, and clears chips instead of packing them. This roundup compares five sets for a magnetic drill on cutting depth, diameter range, shank fit, pilot pins and case.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall KEENTECH 14-PC: Carbide-tipped cutters, a 1-3/8 inch cutting depth, 3 pilot pins and a 1/4-inch wrench for stainless steel and cast iron. Check price on Amazon
- Most Sizes at 2-Inch Depth S&F 13-Pc: 11 cutters from 7/16 to 1-1/16 inch with a 2 inch cutting depth in a solid metal case. Check price on Amazon
- Largest Diameters S&F 6-Pc: 6 cutters from 7/8 to 2 inches with a 2 inch cutting depth in a sturdy aluminum case. Check price on Amazon
- Hardened HSS 65 HRC ZELCAN 11-Pc: M2 HSS hardened to 65 HRC, 11 cutters from 7/16 to 1-1/16 inch and a custom molded case. Check price on Amazon
The machines

KEENTECH 14-PC Carbide-Tipped Annular Cutter Set
A carbide-tipped set with 11 cutters from 7/16 to 1-1/16 inch, a 1-3/8 inch cutting depth, 3 pilot pins and a 1/4-inch wrench.
Pros
- Carbide-tipped cutters for stainless steel, cast iron and carbon steel
- 1-3/8 inch cutting depth across all 11 cutters
- 3 pilot pins and a 1/4-inch wrench in the box
- Triple-edge design spreads the workload across the cutter
Cons
- No warranty term is stated
- Needs cutting fluid for long life; the maker says water limits the cutter to 3 to 5 cuts
- 1-3/8 inch cutting depth is less than the 2 inch depth the S&F sets state
- Diameters stop at 1-1/16 inch, so larger holes need another set

S&F STEAD & FAST Annular Cutter Set 13 Pc
An 11-cutter M2AL HSS set from 7/16 to 1-1/16 inch with a 2 inch cutting depth, 2 pilot pins and a solid metal case.
Pros
- 2 inch cutting depth across all 11 cutters
- 3/4 inch Weldon shank with 2 flats for a secure clamp
- CNC-machined cutters for burr-free holes with minimal deformation
- Solid metal case with 2 pilot pins and a hex wrench
Cons
- For single-layer drilling only, per the maker's caution
- Drill press use needs an additional arbor, not included
- Diameters stop at 1-1/16 inch, so larger holes need another set
- Repeats the common 7/16 to 1-1/16 inch range, so it adds no large diameters

S&F STEAD & FAST Annular Cutter Set 6 Pcs
A 6-cutter M2AL HSS set from 7/8 to 2 inches with a 2 inch cutting depth, 2 pilot pins and a sturdy aluminum case.
Pros
- The only set here that reaches 2 inch diameters
- 2 inch cutting depth on every cutter
- 3/4 inch Weldon shank with 2 flats, stated to fit major mag drill brands
- Sturdy aluminum case keeps 6 cutters and 2 pilot pins organized
Cons
- Only 6 cutters, so the common small sizes need another set
- No hex wrench in the box
- For single-layer drilling only, per the maker's caution
- Drill press use needs an additional arbor, not included

ZELCAN Annular Cutter Set
An 11-cutter M2 HSS set from 7/16 to 1-1/16 inch, hardened to 65 HRC, with a 1 inch cutting depth and a custom molded case.
Pros
- M2 HSS hardened to 65 HRC
- Multi-cut geometry teeth for fast, precise drilling
- 3/4 inch Weldon shank, stated to fit most major mag drill brands
- Spiral groove clears chips to prevent clogging
Cons
- 1 inch cutting depth is less than the 2 inch depth the S&F sets state
- Diameters stop at 1-1/16 inch, so larger holes need another set
- No hex wrench in the box
- No warranty term is stated

VEVOR Annular Cutter Set
An 11-cutter M2AL HSS set from 7/16 to 1-1/16 inch with a 1 inch cutting depth, 2 pilot pins, a hex wrench and a portable foam case.
Pros
- M2AL high-speed steel for wear and heat resistance
- Pointed and flat blades share the cutting load
- Circular groove ejects chips for smooth discharge
- Portable case with a foam lining and a comfortable handle
Cons
- 1 inch cutting depth is less than the 2 inch depth the S&F sets state
- Diameters stop at 1-1/16 inch, so larger holes need another set
- No shank diameter is stated, so check the fit with your magnetic drill
- Two pilot pin sizes, 4.74 mm and 6.35 mm, to keep track of
Other welders and gear to compare
13 pcs Annular Cutter Set OSCARBIDECheck price on Amazon
OSCARBIDE Annular Cutter Set 7pcCheck price on Amazon
TCT Hole Saw SetCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Cutters | Diameter range | Cutting depth | Shank | Pilot pins | Warranty |
|---|---|---|---|---|---|---|---|
| KEENTECH 14-PC | 9.7/10 | 11 | 7/16 to 1-1/16 in | 1-3/8 in | 3/4 in Weldon | 3 | None stated |
| S&F 13-Pc | 9.7/10 | 11 | 7/16 to 1-1/16 in | 2 in | 3/4 in Weldon | 2 | None stated |
| S&F 6-Pc | 9.6/10 | 6 | 7/8 to 2 in | 2 in | 3/4 in Weldon | 2 | None stated |
| ZELCAN 11-Pc | 9.6/10 | 11 | 7/16 to 1-1/16 in | 1 in | 3/4 in Weldon | 2 | None stated |
| VEVOR 13-Pc | 9.6/10 | 11 | 7/16 to 1-1/16 in | 1 in | Not stated | 2 | None stated |
Treat the specs as maker ratings pulled straight from the listings; we gathered them on 18 November 2026.
Buying guide: the best annular cutter set
Cutting depth
Cutting depth decides how thick a plate the cutter can pass in one pass. The sets here state 1, 1-3/8 or 2 inches of cutting depth: the VEVOR and ZELCAN sets state 1 inch, the KEENTECH set states 1-3/8 inches, and both S&F sets state 2 inches. Match the depth to the plate you drill, and check the depth before you order, since a shallow cutter cannot finish a thick plate in one pass.
Diameter range
The diameter range decides which holes the set can drill. Four sets here cover 7/16 to 1-1/16 inch, the common range for plate work, while the 6-piece S&F set covers 7/8 to 2 inches for larger holes. That large set starts at 7/8 inch, so it needs a small set beside it for the common sizes. Pick the range that matches the holes you drill most.
Shank and mag drill fit
The shank decides whether the cutter fits your magnetic drill. The ZELCAN, KEENTECH and both S&F sets state a 3/4 inch Weldon shank, and the KEENTECH listing says to line up the two flats of the shank with the set screws at install. The VEVOR listing states no shank diameter, so check the fit with your drill before ordering. The S&F sets also note that drill press use needs an arbor the set does not include.
Carbide tip vs HSS
Four sets here use high-speed steel, while the KEENTECH set is carbide-tipped. The maker claims the carbide tips cut 3 to 5 times the speed of standard HSS cutters and suit carbon steel, stainless steel, cast iron and tough alloys. The same listing says to use cutting fluid, which enables over 1000 cuts, and says water may limit the cutter to 3 to 5 cuts. Match the tip to the metal you cut most.
Pilot pins and chip clearing
The pilot pin centers the cutter, and the listings say it also controls coolant and clears chips. The KEENTECH set carries 3 pilot pins, while the other four sets carry 2 each. Grooves and flutes clear the chips: the VEVOR set states a circular groove, and the ZELCAN set states a spiral groove. The S&F listings add a caution: annular bits are for single-layer drilling only, so secure the workpiece firmly and start with a low feed rate.
Use as directed. Clamp the work firmly, wear eye and face protection, keep guards in place, and keep gloves away from rotating parts. Annular bits are for single-layer drilling only, so secure the workpiece firmly and start with a low feed rate before increasing it once the cutter is 2 to 3 mm into the material. See the drill press safety page for more on safe drilling.
Before You Strike an Arc
- Check that the Weldon shank fits your magnetic drill and that the two flats line up with the set screws.
- Check the pilot pins are in the case and seated before the first hole: the KEENTECH set carries 3, the other four sets carry 2.
- Clamp the work firmly; annular bits are for single-layer drilling only.
- Have cutting fluid on hand for the carbide-tipped set; the maker says water may limit the cutter to 3 to 5 cuts.
- Check the case contents on arrival: 11 cutters in four of the sets, 6 in the large S&F set.
FAQ for welders
How do you use an annular cutter?
Fit the cutter in the magnetic drill with the pilot pin seated, and clamp the work firmly. Start with a low feed rate and increase it once the cutter is 2 to 3 mm into the material. The cutter removes only the hole edge instead of the entire hole area, so it cuts faster than a standard drill bit.
What is an annular cutter bit?
An annular cutter bit is a hollow cutter that drills a hole by cutting only its rim, rather than removing all the material in the hole. It fits a magnetic drill on a Weldon shank, with a pilot pin that centers the cut. The sets here run from 7/16 to 2 inches in diameter.
How do you sharpen annular cutters?
None of the listings here states a sharpening method. The KEENTECH listing says to use cutting fluid, which the maker says enables over 1000 cuts, and says water may limit the cutter to 3 to 5 cuts. When the edge dulls, follow the maker’s guidance for that set.
What is an annular hole cutter?
An annular hole cutter is another name for an annular cutter: a hollow cutter that cuts a hole by its rim. The sets here call the tool an annular cutter, a mag drill bit and a core drill. It fits a magnetic drill on a Weldon shank.
What is an annular cutter set?
A set of annular cutters in a case, in a range of diameters for one magnetic drill. The sets here hold 6 or 11 cutters, with 2 or 3 pilot pins and, in three sets, a hex wrench. The diameters run from 7/16 to 2 inches across the five sets.
Related: best magnetic drill press, best annular cutter for magnetic drill, annular cutter vs twist drill bit, annular cutter vs hole saw, and the sheet metal and tubing hub.
Scoring, line by line
Each set is scored on performance, build, value, safety listing and warranty, with the weights published on the How We Pick page. Annular cutters have no electrical safety listing to state, and none of the listings here states a warranty term, so every set here scores zero on those two criteria; the ranking comes from performance, build and value.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| KEENTECH 14-PC | 9.7 | 33 | 22 | 21 | n/a | 0 |
| S&F 13-Pc | 9.7 | 32 | 22 | 21 | n/a | 0 |
| S&F 6-Pc | 9.6 | 30 | 21 | 20 | n/a | 0 |
| ZELCAN 11-Pc | 9.6 | 29 | 20 | 21 | n/a | 0 |
| VEVOR 13-Pc | 9.6 | 29 | 20 | 20 | n/a | 0 |
Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score. Safety points apply to gear that runs on power or lists safety features. Without either, we score out of 90 instead of 100.




