Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Screw Extractor Size Chart for Broken Bolts

A screw extractor size chart matches the extractor to the broken fastener, and this guide lays out the stated size ranges of four sets, from 2 mm to 23 mm, so you can pick the right one.

Screw Extractor Size Chart for Broken Bolts
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 139-Piece Damaged Screw Extractor Set with 3/8"39-Piece Damaged Screw Extractor Set with 3/8"9.5/10View on Amazon
  2. 2NEIKO 04204A Hex-Head Multispline Screw and BoltNEIKO 04204A Hex-Head Multispline Screw and Bolt9.5/10View on Amazon
  3. 3VEVOR 49-Piece Bolt Extractor Kit and Easy OutVEVOR 49-Piece Bolt Extractor Kit and Easy Out9.4/10View on Amazon
  4. 4GEARWRENCH 4 PC. Bolt Biter Screw Extraction SetGEARWRENCH 4 PC. Bolt Biter Screw Extraction Set9.4/10View on Amazon

A bolt snaps off flush with the surface, and the stub left behind will not turn with pliers or a wrench. A screw extractor size chart matches the extractor to the broken fastener, so the drilled hole and the extractor fit the stub instead of splitting it. This guide lays out what the four extractor sets state about size and shows how to read the chart.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

39-Piece Damaged Screw Extractor Set with 3/8"

39-Piece Damaged Screw Extractor Set with 3/8"

THINKWORK9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 39-piece set covering 2 mm to 21 mm, with Cr-Mo steel and HSS 6542 extractors at 68 HRC and a blow-mold case.

Pros

  • Widest stated low end here, starting at 2 mm
  • Cr-Mo steel and HSS 6542 at 68 HRC, the only stated hardness here
  • Includes a knockout pin, drill adapter, extractor adapter and bit holder
  • Clear laser-etched markings for identification in low light

Cons

  • No drill bits are listed in the set
  • No warranty term is stated
  • The listing gives no weight or case dimensions
  • Drive size is stated as a fraction with no metric figure
NEIKO 04204A Hex-Head Multispline Screw and Bolt

NEIKO 04204A Hex-Head Multispline Screw and Bolt

NEIKO9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 25-piece CrMo set covering 3.5 mm to 23 mm, with hex heads for wrenches or sockets and laser-etched markings.

Pros

  • Widest stated top end here, up to 23 mm
  • Precision-machined hex heads for use with wrenches or sockets
  • Laser-etched marking on each piece for easy identification
  • Comes in a durable storage case

Cons

  • No warranty term is stated
  • No drill bits are listed in the set
  • No weight or case dimensions are stated
  • The listing gives no hardness figure
VEVOR 49-Piece Bolt Extractor Kit and Easy Out

VEVOR 49-Piece Bolt Extractor Kit and Easy Out

VEVOR9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 49-piece kit with nut extractors, screw extractors, spiral extractors, drill bits and adapters in an organized case.

Pros

  • Most pieces here: 49 in one kit
  • Includes drill bits: 10 small drill bits and 6 drill bits
  • Includes 13 nut extractors alongside the screw extractors
  • Laser-etched markings and an organized case

Cons

  • No size range is stated for the extractors
  • Steel type is not named beyond selected steels
  • The listing gives no hardness figure
  • Drill bits and adapters take up much of the 49-piece count
GEARWRENCH 4 PC. Bolt Biter Screw Extraction Set

GEARWRENCH 4 PC. Bolt Biter Screw Extraction Set

GEARWRENCH9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 4-piece large bolt biter set in chrome, with a bi-directional design and hex base for hand and power tools.

Pros

  • Bi-directional design loosens or tightens damaged fasteners
  • Hex base works with hand and power tools
  • High-visibility laser markings for size identification
  • Tapered side and tip cutting edges for extraction

Cons

  • Only 4 pieces, the fewest here
  • No size range is stated beyond Large
  • No drill bits or storage case are listed
  • The maker claims up to 50 times longer life with no basis stated in the listing

The screw extractor size chart

Start with the size of the broken screw or bolt, then find a set whose stated range covers it. The chart below lists what each listing states. Two sets state a size range in millimeters, and two state no range at all, so the range column reads as stated rather than guessed.

Set Stated size range Pieces
NEIKO 04204A 3.5 mm to 23 mm 25
VEVOR YMWJ49 Not stated 49
THINKWORK W6081 2 mm to 21 mm 39
GEARWRENCH 84787 Not stated 4

Millimeter ranges read small to large. A set that starts low covers small screws, and a set that ends high covers larger bolts. When a listing states no range, the piece count and the contents list are all you have to judge it by.

How to read the chart

Match the extractor to the fastener, not to the drill. The extractor must bite into the stub, so the set needs a size close to the broken fastener. Laser-etched markings on the extractor show its size, and every set here states laser-etched markings of some kind. Check the marking before you drill, and keep the set in its case so the sizes stay in order.

  • Measure the fastener. Find the size of the broken screw or bolt before you pick an extractor.
  • Check the range. The set must list a size that covers the fastener.
  • Read the marking. Laser-etched markings show the size on each piece.

Side by side

Size range Pieces Material Case
THINKWORK W6081 2 mm to 21 mm 39 Cr-Mo steel, HSS 6542 Blow-mold case
NEIKO 04204A 3.5 mm to 23 mm 25 CrMo Storage case
VEVOR YMWJ49 Not stated 49 Steel, type not stated Organized case
GEARWRENCH 84787 Not stated 4 High strength steel Not stated

The two sets with stated ranges cover different ground. The THINKWORK set starts lower, and the NEIKO set ends higher. The VEVOR kit (on Amazon) trades a stated range for the most pieces, including drill bits and adapters, while the GEARWRENCH set is the smallest kit here.

Screw extractor sets for broken bolts

Two sets below state a size range and two state none, so the right pick depends on the fastener sizes on your bench, and the kit contents decide what else you need for the job.

How to pick the right size

Pick by the fasteners you face most often. A set that starts at 2 mm suits small screws, and a set that ends at 23 mm suits larger bolts. If your bench sees both, the two ranged sets together cover the spread, while the VEVOR kit adds drill bits and adapters for jobs where the extractor alone is not enough.

For a closer look at complete kits, see the best screw extractor set guide, and for the wider family of tools, the best bolt extractor set roundup.

FAQ for welders

What size screw extractor do I need for a broken bolt?

Match the extractor to the size of the broken fastener. The THINKWORK set covers 2 mm to 21 mm, and the NEIKO set covers 3.5 mm to 23 mm. Sets with no stated range need the listing checked before you buy.

Do I need a drill bit with a screw extractor set?

Most sets here list no drill bits, so you supply your own. The VEVOR kit is the exception, with 10 small drill bits and 6 drill bits in the box, plus adapters. Check the contents list before you buy, since a set without drill bits leaves you short on the day.

What is the difference between a screw extractor and a bolt extractor?

Screw extractors bite into a drilled hole in the broken fastener, while bolt extractors grip the outside of a rounded head or nut. The VEVOR kit includes both kinds, with 13 nut extractors alongside its screw extractors. The screw extractor vs bolt extractor guide covers the difference in full.

Can one extractor set cover every broken fastener?

No single set here covers every size. The stated ranges stop at 21 mm and 23 mm, and two sets state no range at all. Pick the set whose stated range covers the fasteners on your bench, and add a second set if your work spans small screws and large bolts.

How do I tell extractor sizes apart in a set?

Read the laser-etched marking on each piece. Every set here states laser-etched markings, and the NEIKO set marks each piece for easy identification. Keep the pieces in the case in size order so the right one is easy to find.

Related: best screw extractor set, screw extractor set how to use, best bolt extractor set, and the metal fab tools hub. Also see the screw extractor vs bolt extractor.

More buying guides

Metal Fab Tools ·

Best Screw Extractor (2026)

Five screw extractors, pliers and kits, compared by size range, steel, hardness and warranty, for stripped, rusted and broken fasteners.