Cutting Torch Repair Kit: What to Buy
A cutting torch repair kit restores a leaking hose or a worn torch with seals, fittings and ferrules, and the right kit depends on the hose size or the torch model.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
YESWELDER 60-Piece PT31 Plasma Consumables Kit forView on Amazon - 2
YESWELDER 110-Piece PT31 Plasma Consumables Kit forView on Amazon - 3
Kodilin Brazing Torch Kit for MAPP Gas & PropaneView on Amazon - 4
RX WELD Heavy Duty Oxy Acetylene Torch Kit with Check ValvesView on Amazon
A cutting torch that hisses at the handle, pops when it lights, or weeps gas where the hose meets the fitting is telling you a seal or a hose end has given up. A cutting torch repair kit is the box of seals, fittings, and ferrules that puts that torch back to work without buying a whole new torch. The trick is buying the kind that matches the failure: a hose splice kit for a damaged hose, a rebuild kit for a leaking torch body, or an O-ring set for a head that no longer seals to the handle.
Other welders and gear to compare
YESWELDER 60-Piece PT31 Plasma Consumables Kit forCheck price on Amazon
YESWELDER 110-Piece PT31 Plasma Consumables Kit forCheck price on Amazon
Kodilin Brazing Torch Kit for MAPP Gas & PropaneCheck price on Amazon
RX WELD Heavy Duty Oxy Acetylene Torch Kit with Check ValvesCheck price on Amazon
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
What a cutting torch repair kit fixes
Most failures happen in 2 places. Hoses fail at the ends, where the fitting works loose, and along the run, where a cut, kink, or burn opens a leak. Torch bodies fail at the seals inside the valves and at the joint where the cutting head meets the handle. A hose kit and a torch rebuild kit fix different failures, so the first step is finding where the gas escapes: soapy water brushed on a joint that bubbles under pressure shows a leak plainly. Start with the torch model and the hose size. See the parts of a cutting torch to match each part to its place on the torch.
Hose splice kits: what is in the box
A hose splice kit is built around brass fittings that join a cut hose back together. The ZGTools 24 piece kit holds 6 barbed nipples, 12 ferrules, and 6 hose nuts in brass rated for 200 psi, sized for 1/4 inch ID hose, and its fittings comply with CGA standards for oxy-acetylene and acetylene and propane gases. The larger 49 piece kits add a handheld crimper and a storage box: one lists 12 ferrules, 8 splicers, 8 nipples, 4 oxygen nuts, and 4 acetylene nuts, while the other adds 8 braces, 2 oxygen couplers, and 2 acetylene couplers. Both fit 3/16 inch and 1/4 inch ID hose with Type B 9/16 inch fittings, and the crimper presses each ferrule with a squeeze, so the repair needs no vise and no shop press. Measure the hose ID before ordering, because a 1/4 inch kit does not fit a 3/16 inch hose. See the welding hose repair kit guide for more on hose work.
Cutting torch repair kit: match the torch model first
Rebuild kits are model specific, and the part number matters more than the brand on the box. The TWSupply and Pidnsrozo kits built around part number 0390-0057 fit Victor CA2460 and CA2470 cutting torches, with valve stems, bushings, seats, sleeves, O-rings, a PTFE washer, and a diaphragm seal in the full overhaul set. A separate TWSupply kit covers Harris 72-3 and 72-3A torches, with O-rings, a plunger, and a seat assembly. The high pressure oxygen valve seat kit, part number 0390-0043, fits ST900FC, CA411-1, CA1060, CA1050, HC1100C, HC1200, and most Victor straight cutting torches. For a leak at the torch head, the Cutetool O-ring (on Amazon) set fits Victor CA1350 and CA1260 torches and FC100 and FC150 handles, with 2 large 13A and 2 small 13B O-rings in each of 2 sets. Read the model stamp on the torch body before ordering.
Side by side
| Hose splice kit | Torch rebuild kit | O-ring seal kit | |
|---|---|---|---|
| What it fixes | Cut or leaking hose ends | Leaking valves and worn internal seals | Leaks at the torch head to handle joint |
| Fits | 3/16 inch and 1/4 inch ID hose, Type B 9/16 inch fittings | Victor CA2460 and CA2470, Harris 72-3 and 72-3A | Victor CA1350 and CA1260, FC100 and FC150 handles |
| Parts inside | Ferrules, nipples, nuts; 49-piece kits add splicers, couplers, braces and a crimper | O-rings, valve stem, bushings, seats, washers | 2 large 13A and 2 small 13B O-rings per set |
| Count | 49 pieces or 24 pieces | 1 kit per torch model | 2 sets |
| Check before ordering | Measure the hose ID and fitting size | Match the torch model and part number 0390-0057 | Match the 13A and 13B sizes to the torch head |
The table above shows the split at a glance: hose kits are sized by hose ID, torch kits are matched by model and part number. A kit that covers one side does not cover the other, so check both the hose and the torch before ordering. If the torch itself is worn out, see the best heavy duty cutting torch guide for a replacement.
How a hose splice repair goes
Cut out the damaged section with a clean square cut, then slide a ferrule onto each hose end and push a barbed splicer or nipple into the hose until it seats. Crimp the ferrule over the barb with the handheld crimper from the kit, then reconnect the hose ends to the torch and the regulator, keeping the oxygen and acetylene ends on their matching sides. Open the gas slowly and brush soapy water over each joint; bubbles mean the joint needs another look before the torch lights. See the oxy fuel cutting setup guide for hoses, regulators, and tips.
How to pick the right kit
- Find the leak first. A hose leak calls for a splice kit, a valve leak calls for a rebuild kit, and a head joint leak calls for an O-ring set.
- Measure the hose. The 49 piece kits fit 3/16 inch and 1/4 inch ID hose with Type B 9/16 inch fittings, while the 24 piece kit fits 1/4 inch ID hose only.
- Match the model and part number. Read the model stamp on the torch body, such as part number 0390-0057 for Victor CA2460 and CA2470 torches.
- Check what is in the box. The 49 piece kits include a handheld crimper and a storage box, while the 24 piece kit lists nipples, ferrules and hose nuts, with no crimper named.
- Check the warranty. The ZGTools 24 piece kit states a 1 year warranty.
The metal fab tools section holds more cutting torch repair kit buying guides for shop work.
Safety notes for oxy-fuel repair
Oxy-fuel gas burns hot, and a leak is easy to miss until the torch pops or the flame goes unsteady. Shut the torch off and disconnect the gas supply before changing O-rings or opening a valve, and clean the sealing surfaces before fitting new seals. Worn O-rings can let gas slip past the seal and raise the risk of flashback, so a head that leaks at the handle joint needs new seals before it goes back to work. The brass fittings in the ZGTools 24 piece kit are rated for 200 psi. Keep cylinders upright and chained, clear flammable material from the area, and work with ventilation. Read oxy acetylene torch safety and the cutting torch tips sizes charts before lighting up after a repair.
FAQ for welders
Can a cutting torch repair kit fix a leaking hose?
Yes, when the damage is a cut, a kink, or a bad hose end. Cut out the damaged section, splice in new brass fittings with the ferrules from the kit, and check each joint with soapy water before lighting the torch.
How do I know which rebuild kit fits my torch?
Read the model stamp on the torch body and match it to the kit. Part number 0390-0057 fits Victor CA2460 and CA2470 torches, the Harris kit fits 72-3 and 72-3A torches, and part number 0390-0043 fits the high pressure oxygen valve on ST900FC, CA411-1, CA1060, CA1050, HC1100C, and HC1200 torches.
What size hose does a hose repair kit fit?
The 49 piece kits fit 3/16 inch and 1/4 inch ID hose with Type B 9/16 inch fittings, and the 24 piece kit is sized for 1/4 inch ID hose. Measure the hose ID before ordering, since a kit sized for one ID does not fit the other.
Do I need a crimper for a hose repair kit?
The 49 piece kits include a handheld crimper that presses each ferrule with a squeeze, so no vise and no shop press is needed. The 24 piece kit lists nipples, ferrules and hose nuts, with no crimper named.
When should I replace the torch instead of repairing it?
Repair makes sense when the failure is a seal, a valve seat, or a hose end. When the torch body is cracked, the valve threads are stripped, or the same leak returns after new seals, the torch has no repair left in the kits and a replacement is the safer call.
Related: parts of a cutting torch, welding hose repair kit, cutting torch tips sizes charts, and welding torch types.




