Oxy Acetylene Torch Safety: Gear and Practices
Oxy acetylene torch safety starts with a flashback arrestor on each gas line: torch-end and regulator-end sets compared on pressure figures, threads and fit.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Vaphy Oxygen Acetylene Flashback Arrestors Set9.6/10View on Amazon - 2
Uenede Oxygen & Acetylene Flashback Arrestors Set9.6/10View on Amazon - 3
VAPHY Oxygen Acetylene Flashback Arrestors Set9.5/10View on Amazon - 4
Victor Technologies 0656-0004 FBR-1 300 Series9.5/10View on Amazon
Oxy acetylene torch safety is about stopping a flame from running back down the hose into the cylinders. A flashback arrestor with a one-way valve sits between the torch and the hose or at the regulator, and it lets gas flow one way only. This guide covers where arrestors go, the pressure figures the listings state, and the gear that does the job.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Vaphy Oxygen Acetylene Flashback Arrestors Set
A 2-pack of pure copper torch-end flashback arrestors with one-way check valves, rated to 20bar/290PSI for oxygen and 1.5bar/21PSI for acetylene.
Pros
- 2-pack covers both gas lines
- Pure copper construction, per the listing
- Oxygen check valve rated to 20bar/290PSI
- 9/16-18 B size threads, per the listing
Cons
- No warranty term is stated
- No weight or size is stated
- No fitting size beyond the 9/16-18 thread is stated
- Torch end only; a regulator-end set is a separate purchase

Uenede Oxygen & Acetylene Flashback Arrestors Set
A solid brass regulator-end flashback arrestor set with internal check valves for oxygen and acetylene, rated to 15bar/210PSI for oxygen and 1.5bar/21PSI for acetylene.
Pros
- Internal check valves for oxygen and acetylene
- Solid brass construction, per the listing
- Acetylene arrestor also works for propane or Mapp gas, per the listing
- 9/16-18 threads, B size, per the listing
Cons
- No warranty term is stated
- No weight or size is stated
- Oxygen figure of 15bar/210PSI is lower than the Vaphy listings
- Regulator end only; a torch-end set is a separate purchase

VAPHY Oxygen Acetylene Flashback Arrestors Set
A pure copper torch-end flashback arrestor set with one-way check valves, rated to 20bar/290PSI for oxygen and 1.5bar/21PSI for acetylene.
Pros
- Pure copper construction, per the listing
- Oxygen check valve rated to 20bar/290PSI
- Acetylene check valve rated to 1.5bar/21PSI
- 9/16-18 B size threads, per the listing
Cons
- No warranty term is stated
- No weight or size is stated
- One set only, unlike the 2-pack listing
- Torch end only; a regulator-end set is a separate purchase

Victor Technologies 0656-0004 FBR-1 300 Series
A regulator-mount flashback arrestor pair for 400 and 300 Series handles and attachments, with no pressure figure or thread size stated.
Pros
- Regulator-mount type, per the listing
- Made for 400 and 300 Series handles and attachments
- Weighs 0.4 pounds, per the spec table
- Manufacturer warranty stated
Cons
- No pressure figure is stated
- No thread size is stated
- No material is stated
- Warranty term is not given, only Manufacturer Warranty
Oxy acetylene torch safety: the short answer
Fit a flashback arrestor on each gas line, check the pressure figure on the listing, and match the thread to the torch or regulator. Torch-end arrestors sit between the torch and the hoses, and regulator-end arrestors attach at the regulator. The listings here state oxygen figures of 20bar/290PSI and 15bar/210PSI, and an acetylene figure of 1.5bar/21PSI, all on 9/16-18 B size threads where stated.
Torch end or regulator end
The mounting point is the first choice. The Vaphy listings are torch-end arrestors, made to sit between the torch and the hoses. The Uenede listing is a regulator-end set that attaches at the regulator, and the Victor listing is a regulator-mount arrestor for use with 400 and 300 Series handles and attachments. A torch-end arrestor guards the hose, and a regulator-end arrestor guards the regulator and cylinder. Fit one on each gas line, oxygen and acetylene, since the listings sell them as sets for both gases.
Flashback arrestors side by side
| Gear Score | End | Oxygen max | Acetylene max | |
|---|---|---|---|---|
| Vaphy 2-Pack Torch End | 9.6/10 | Torch end | 20bar/290PSI | 1.5bar/21PSI |
| Uenede Regulator End | 9.6/10 | Regulator end | 15bar/210PSI | 1.5bar/21PSI |
| Vaphy Torch End Single | 9.5/10 | Torch end | 20bar/290PSI | 1.5bar/21PSI |
| Victor FBR-1 300 Series | 9.5/10 | Regulator mount | Not stated | Not stated |
Pressure figures are the maximum the arrestor bears, as stated in each listing. The Victor listing states no pressure figure and no thread size, so check the listing and the manual before ordering.
Check the pressure figures and the threads
Match the arrestor to the gas and the pressure. The Vaphy listings state an oxygen check valve rated to 20bar/290PSI and an acetylene check valve rated to 1.5bar/21PSI, on 9/16-18 B size threads. The Uenede listing states an oxygen figure of 15bar/210PSI and the same acetylene figure of 1.5bar/21PSI, on 9/16-18 threads, B size. The Victor listing states no pressure figure and no thread size. The Uenede acetylene arrestor (on Amazon) also works for propane or Mapp gas, per the listing.
Before you order
Check the listing for the end type, the thread size and the pressure figures before you buy. Torch-end arrestors fit between the torch and the hoses, and regulator-end arrestors fit at the regulator. Match the thread to the torch or regulator: the Vaphy and Uenede listings state 9/16-18 threads, B size, while the Victor listing states no thread size. Count the sets: the Vaphy 2-pack gives two sets in one order, while the single set and the regulator sets give one set each.
The gear for oxy acetylene torch safety
Each arrestor below handles one part of the job: the torch-end sets guard the hose, and the regulator-end sets guard the regulator. The cards carry the specs and the scores. For the torch itself, see the oxy acetylene torch setup guide.
Flashback and cylinders. A flashback can run back through the hose toward the regulator and the cylinders, which is why the arrestor sits in the line. Keep gas cylinders upright and chained, and clear anything flammable from the area. See the OSHA welding overview and our Safety Disclaimer.
For more options, see our welding safety gear guides.
FAQ for welders
Where does a flashback arrestor go?
Between the torch and the hoses, or at the regulator. The Vaphy listings are torch-end arrestors, and the Uenede and Victor listings are regulator-end arrestors. Fit one on each gas line, oxygen and acetylene.
What thread size do these arrestors use?
The Vaphy and Uenede listings state 9/16-18 threads, B size. The Victor listing states no thread size, so check the listing and the manual before ordering.
What pressure do the arrestors bear?
The Vaphy listings state 20bar/290PSI for oxygen and 1.5bar/21PSI for acetylene. The Uenede listing states 15bar/210PSI for oxygen and 1.5bar/21PSI for acetylene. The Victor listing states no pressure figure.
Can an acetylene arrestor work with propane?
The Uenede listing states its acetylene arrestor can also be used for propane or Mapp gas. The other listings state no other gas use, so check the listing before using one with another gas.
Do I need an arrestor on both gas lines?
Yes. The listings sell arrestors as sets for oxygen and acetylene, with a check valve for each gas. A torch-end set sits between the torch and the hoses, and a regulator-end set attaches at the regulator.
Related: oxy acetylene torch setup, oxy fuel cutting setup, acetylene regulators for torches, and heavy duty cutting torches. Also see our cutting torch tip sizes charts.




