How to Use Pipe Threader: A Step-by-Step Guide
A manual ratchet pipe threader cuts threads on pipe with a die head matched to the pipe size, and this guide covers the steps, the die ranges and the kits in this guide.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
RIDGID 36475 Exposed Ratchet Threader Set9.7/10View on Amazon - 2
VEVOR Ratchet Pipe Threader Kit with 6 Dies9.6/10View on Amazon - 3
Yaegoo Ratchet Pipe Threader Kit with 6 Dies9.6/10View on Amazon - 4
36475 12-R Manual Exposed Ratchet Pipe Threader9.6/10View on Amazon
A pipe run needs a threaded end, and the fitting will not start on a bad thread. How to use pipe threader comes down to one thing: pick the die head that matches the pipe size, fit it in the ratchet, and turn the handle until the thread runs true. The steps below use the manual ratchet kits in this guide, from the small-pipe kits to the large-pipe sets.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

RIDGID 36475 Exposed Ratchet Threader Set
A RIDGID 12-R exposed ratchet threader set with 6 die heads from 1/2 in to 2 in NPT, ductile cast iron heads and a lifetime warranty.
Pros
- 6 die heads from 1/2 in to 2 in NPT, each fitting the ratchet without extra pieces
- Ductile cast iron die heads with alloy dies
- Lifetime warranty against defects in material or workmanship
- Carrying case with labeled compartments for each die head
Cons
- Heaviest here at 35.12 pounds
- No certification is stated in the listing
- Included heads start at 1/2 in, not 1/8 in
- No extension bar is listed, unlike the VEVOR

VEVOR Ratchet Pipe Threader Kit with 6 Dies
A VEVOR ratchet pipe threader kit with 6 dies from 1/4 in to 1-1/4 in NPT, a handle with an extension bar and a carrying case.
Pros
- 6 dies from 1/4 in to 1-1/4 in NPT in one kit
- Handle with an extension bar for more torque
- Cast iron hinge plate head with 9SICR die head teeth
- 13.2 pounds with a portable carrying case
Cons
- No warranty term is stated in the listing
- No certification is stated in the listing
- Largest die is 1-1/4 in, below the 12-R sets
- No labeled compartments are listed for the case

Yaegoo Ratchet Pipe Threader Kit with 6 Dies
A Yaegoo ratchet pipe threader kit with 6 dies from 1/4 in to 1-1/4 in NPT, a long handle and a red ABS plastic case.
Pros
- 6 dies from 1/4 in to 1-1/4 in NPT in one kit
- Long handle for more torque with less effort
- Galvanized iron, durable and wear-resistant, per the listing
- Red ABS plastic case holds the heads and the handle
Cons
- Listing names the after-sales brand as Geeyae, not Yaegoo
- No warranty term is stated in the listing
- No certification is stated in the listing
- Largest die is 1-1/4 in, below the 12-R sets

36475 12-R Manual Exposed Ratchet Pipe Threader
A Yoursme 12-R manual ratchet pipe threader kit with 6 dies from 1/2 in to 2 in NPT and a carrying case.
Pros
- 6 die heads from 1/2 in to 2 in NPT, each fitting the ratchet without extra pieces
- Ductile cast iron die heads with alloy dies
- 1/8 in to 2 in pipe capacity with 12-R die heads
- Carrying case for organized use on job sites
Cons
- Listing uses the RIDGID 36475 number and the 12-R name
- No warranty term is stated in the listing
- No certification is stated in the listing
- No weight or dimensions are stated in the listing
How to Use Pipe Threader: The Steps
- Pick the die for the pipe size. Match the die head to the pipe: the 6-die kits in this guide cover 1/4 in to 1-1/4 in NPT, and the 12-R sets cover 1/2 in to 2 in NPT. A die that does not match the pipe will not cut a thread the fitting can use.
- Fit the die head in the ratchet. Each die head fits in the ratchet without any additional pieces, per the RIDGID and Yoursme listings. Seat it all the way home before you start turning.
- Oil the cut as the manual directs. The listings here name no cutting oil, so follow the manual for the cut. Oil keeps the dies cool and the thread clean.
- Turn the handle. The long handle gives the torque, and the VEVOR adds an extension bar for more leverage. Turn steady and let the die do the cutting.
- Swing the handle back with the ratchet. Turn the handle forward to cut, then reverse the ratchet to swing the handle back for the next pull. The die head stays on the pipe, so the thread keeps cutting in the same direction without taking the head off.
- Check the thread. Run a fitting onto the threaded end by hand to check the thread. If it binds or will not start, clean the thread and check the die size again.
- Repair a damaged thread with the matching die. The VEVOR and Yaegoo listings name repairing damaged threads as a use. Pick the die for the pipe size and run it over the damaged thread to clean it up.
| Gear Score | Die range | Weight | Warranty | |
|---|---|---|---|---|
| RIDGID 12-R Set | 9.7/10 | 1/2 in to 2 in NPT | 35.12 pounds | Lifetime |
| VEVOR 6-Die Kit | 9.6/10 | 1/4 in to 1-1/4 in NPT | 13.2 pounds | Not stated |
| Yaegoo 6-Die Kit | 9.6/10 | 1/4 in to 1-1/4 in NPT | 12.38 pounds | Not stated |
| Yoursme 12-R Kit | 9.6/10 | 1/2 in to 2 in NPT | Not stated | Not stated |
The chart above ranks the kits by their Gear Score, with the die range, weight and warranty beside each one. The RIDGID set leads on the lifetime warranty, while the 6-die kits lead on weight: the Yaegoo has the lowest stated weight here at 12.38 pounds, and the VEVOR follows at 13.2 pounds.
Pick the Right Die
Die range is the first choice, and it splits the kits in this guide by size. The VEVOR and Yaegoo kits each hold 6 dies from 1/4 in to 1-1/4 in NPT, which covers small pipe for plumbing repair. The RIDGID and Yoursme sets each hold 6 die heads from 1/2 in to 2 in NPT, and both take any 12-R die head for a 1/8 in to 2 in pipe capacity.
Pipe material matters too. The VEVOR suits aluminum, iron, galvanized steel and copper, per the listing, and the Yoursme suits aluminum, iron, galvanized and copper. The Yaegoo suits steel, galvanized, iron and plastic pipes. Match the die to the pipe size first, then check the listing for the pipe material you are threading.
What the Handle and the Case Do
The handle is where the torque comes from. Three of the kits list a long handle: the VEVOR, the Yaegoo and the Yoursme. The VEVOR adds an extension bar for more leverage. The Yaegoo handle is shaped for grip, and the RIDGID set is listed as purpose built for professionals. A longer handle gives more torque with less effort, per those listings, which matters on a long run of pipe.
The case keeps the set together. All 4 kits list a carrying case, and the RIDGID case (on Amazon) has labeled compartments for each die head, so the right head is easy to find. The Yaegoo case is red ABS plastic, and the VEVOR case is built for carrying the kit to the job. Keep the dies in the case so they stay clean and easy to find.
The Threaders in This Guide
Each threader below fits a different job: the RIDGID set for a professional who wants a lifetime warranty, the VEVOR kit for small pipe with an extension bar, the Yaegoo kit for the lowest stated weight, and the Yoursme kit (on Amazon) for a 12-R set that states no warranty.
Before You Thread
Clamp the pipe before you thread it. A pipe held by hand will turn with the die, so hold it in a pipe vise and check that it cannot move. See the best vise for pipe for vises that hold pipe while you work. Wear eye protection, keep hands clear of the die head while it turns, and keep the work area clear of anything the handle can hit as it swings.
FAQ for welders
What size pipe threader do I need?
Match the die to the pipe size. The 6-die kits in this guide cover 1/4 in to 1-1/4 in NPT, and the 12-R sets cover 1/2 in to 2 in NPT, with a 1/8 in to 2 in capacity for any 12-R head. Measure the pipe first, then pick the kit whose dies cover it.
Can I repair a damaged thread with a pipe threader?
Yes. The VEVOR and Yaegoo listings name repairing damaged threads as a use. Pick the die that matches the pipe size and run it over the damaged thread to clean it up, then check the thread with the fitting it joins.
Do I need cutting oil to thread pipe?
Follow the manual for the cut. The listings here name no cutting oil, so the manual is the authority on the cut. Oil keeps the dies cool and the thread clean.
What is the difference between the 6-die kits and the 12-R sets?
The 6-die kits cover 1/4 in to 1-1/4 in NPT and weigh 13.2 pounds for the VEVOR and 12.38 pounds for the Yaegoo. The 12-R sets cover 1/2 in to 2 in NPT, and the RIDGID set adds a lifetime warranty while the Yoursme kit states none. The RIDGID set weighs 35.12 pounds, and the Yoursme kit states no weight.
How heavy is a manual pipe threader kit?
It depends on the set. The Yaegoo kit weighs 12.38 pounds, the VEVOR kit weighs 13.2 pounds, and the RIDGID set weighs 35.12 pounds. The Yoursme kit states no weight, so there is no figure to compare against the rest.
Related: tube cutter vs pipe cutter, best combination bench and pipe vise, steel pipe cutter vs hacksaw and the metal fab tools hub.




