Tube Cutter vs Pipe Cutter: Which One Should You Buy?
The Ridgid tubing cutter and the KNIPEX pipe cutter cover different capacity ranges and different adjustment styles, so the right pick depends on the tube and pipe sizes on the job.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Ridgid 31642 model 152 Quick-Acting Tubing Cutter9.7/10View on Amazon - 2
KNIPEX 90 31 02 SBA TubiX Pipe Cutter with Quick9.6/10View on Amazon
Verdict. Pick the Ridgid side for the wider stated capacity range and the lifetime warranty wording, and pick the KNIPEX side for one-handed adjustment and named cutting metals. Neither listing states a safety certification, so neither scores on that part of the card.
A clean cut on small tube or pipe starts before the wheel touches metal: the cutter has to fit the size in hand, turn without a fight, and leave an edge that joins cleanly. This tube cutter vs pipe cutter comparison puts the Ridgid tubing cutter against the KNIPEX pipe cutter on what each listing states, and where each listing stays quiet.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
The two cutters

Ridgid 31642 model 152 Quick-Acting Tubing Cutter
A hand-powered tubing cutter with a 1/4-inch to 2-5/8-inch cutting capacity, a quick-acting design, an X-Cel knob and a fold-away reamer.
Pros
- 1/4-inch to 2-5/8-inch cutting capacity, stated as 6 mm to 66 mm
- Quick-acting design with an X-Cel knob for cutting tubing more quickly
- I-beam construction with hardened wear surfaces and thrust-bearing slide assemblies
- Fold-away reamer to clean the cut end for a better connection
Cons
- No spare cutting wheel mentioned in the listing
- Names trades like plumbing and HVAC, but no tube materials
- Spec table lists color only as 1, with no useful finish detail
- Warranty covers material defects and workmanship only, for the normal life of the product

KNIPEX 90 31 02 SBA TubiX Pipe Cutter with Quick
A hand-powered pipe cutter with QuickLock single-handed quick adjustment, a magnesium body and a deburring tool, cutting copper, brass and high-grade steel from 1/4-inch to 1 3/8-inch.
Pros
- QuickLock single-handed quick adjustment, with one hand pushing the cutting wheel
- Cuts copper, brass, and high-grade steel, from 1/4-inch to 1 3/8-inch
- High-quality needle bearings let the cutting wheel and four guide rollers operate with ease
- Spare cutting wheel stored in the handle for quick replacement
Cons
- Warranty is listed only as Limited Warranty, with no term stated
- Top capacity is 1 3/8-inch, so larger sizes need another cutter
- Title says magnesium body while the spec table lists material only as Blend
Other welders and gear to compare
RIDGID 31622 Model 150 Constant Swing Tubing CutterCheck price on Amazon
Tubing Cutter 1/8" to 1-1/4"Check price on Amazon
HAUTMEC Pro 1/2 Inch Automatic Copper Tube CutterCheck price on Amazon
Mini Copper Pipe Cutter Adjustable Tubing Cutter 3-22mm TubeCheck price on Amazon
RIDGID 32985 Model 104 Close Quarters Tubing CutterCheck price on Amazon
Ridgid 32920 model 15 Screw Feed Tubing CutterCheck price on Amazon
Side by side
| Ridgid 31642 Tubing Cutter | KNIPEX TubiX Pipe Cutter | Takeaway | |
|---|---|---|---|
| Cutting capacity | 1/4-inch to 2-5/8-inch | 1/4-inch to 1 3/8-inch | Ridgid lists the wider top end |
| Weight | 1.8 pounds | 13.3 ounces | Different units in the listings |
| Adjustment | Quick-acting design, X-Cel knob | QuickLock single-handed quick adjustment | Both promise fast adjustment |
| Materials or trades named | Plumbing, HVAC, electrical work | Copper, brass, and high-grade steel | KNIPEX names metals; Ridgid names trades |
| Wheel change | Pin with ball detent, no tool needed | Spare wheel stored in the handle | Both keep wheel changes short |
| Edge finishing | Fold-away reamer | Deburring tool | Both include an edge-finishing tool |
| Build notes | I-beam construction, hardened wear surfaces | Magnesium body, needle bearings, four guide rollers | Different build stories |
| Dimensions | 10 x 5.1 x 2.7 inches | 7.25 x 2.5 x 1.13 inches | Ridgid lists the larger frame |
| Warranty | Lifetime warranty on material defects and workmanship | Limited Warranty | Ridgid states the longer term |
All specs here repeat what the maker rates and the listing prints, copied down 29 October 2026. Neither listing states a safety certification.
Tube Cutter vs Pipe Cutter: Capacity First
Both cutters start at the same bottom end: 1/4-inch. The difference is the top end. The Ridgid listing states a 1/4-inch to 2-5/8-inch range, stated as 6 mm to 66 mm, while the KNIPEX listing states 1/4-inch to 1 3/8-inch. On stated capacity alone, the Ridgid covers the wider range, and the KNIPEX tops out where larger work would need another cutter.
Adjustment and Wheel Changes
Both listings promise fast adjustment, in different words. The Ridgid uses a quick-acting design with an X-Cel knob for cutting tubing more quickly, plus thrust-bearing slide assemblies for smooth operation. The KNIPEX uses QuickLock single-handed quick adjustment, so one hand pushes the cutting wheel while the other holds the work. On wheel changes, the Ridgid pin uses a ball detent design, so the wheel changes with no tool needed and no lost clips, while the KNIPEX stores a spare cutting wheel in the handle for quick replacement.
Weight and Build
The stated weights do not line up directly: the Ridgid listing states 1.8 pounds, while the KNIPEX listing states 13.3 ounces, and neither listing converts the figure. On build, the Ridgid lists I-beam construction with hardened wear surfaces and a metal material, plus Made in USA in its bullets. The KNIPEX listing names a magnesium body, with needle bearings and four guide rollers in its bullets, though its spec table lists material only as Blend, so the body metal reads differently depending on which line is trusted. Dimensions are 10 x 5.1 x 2.7 inches for the Ridgid and 7.25 x 2.5 x 1.13 inches for the KNIPEX.
What Each Listing Leaves Unclear
The Ridgid listing names trades, not metals: plumbing, HVAC, electrical work, DIY projects, professional use and home improvement, with no copper, brass or steel named anywhere. The KNIPEX listing does the opposite, naming copper, brass and high-grade steel, but its spec table lists usage as Cable and Housing Tools, which does not match a pipe cutter at all. The Ridgid spec table also lists color only as 1, with no useful finish detail. On warranty, the Ridgid states a lifetime warranty on material defects and workmanship for the normal life of the product, while the KNIPEX states only a Limited Warranty, with no term. Neither listing states a safety certification, so both score zero on that part of the card.
Choose the Ridgid 31642 Tubing Cutter if
- You cut tubing across a 1/4-inch to 2-5/8-inch range.
- You want a fold-away reamer on the tool for a cleaner connection.
- You want a wheel change with no tool needed and no lost clips.
- A stated lifetime warranty on defects and workmanship matters to you.
Choose the KNIPEX TubiX Pipe Cutter if
- You want QuickLock single-handed quick adjustment.
- Your pipe is copper, brass or high-grade steel inside the stated range.
- You want a spare cutting wheel stored in the handle.
- You want a deburring tool on the cutter itself.
Before You Cut
- Match the cutter to a size inside the range its listing states.
- Check the wheel and the reamer or deburring tool on arrival, plus the spare wheel stored in the KNIPEX handle.
- Wear eye protection and gloves when handling freshly cut metal edges.
- Keep cut ends deburred before fitting, so a rough edge does not spoil the joint.
FAQ for welders
What sizes does each cutter cover?
The Ridgid listing states 1/4-inch to 2-5/8-inch, stated as 6 mm to 66 mm. The KNIPEX listing states 1/4-inch to 1 3/8-inch.
Which cutter adjusts with one hand?
The KNIPEX listing states QuickLock single-handed quick adjustment, with one hand pushing the cutting wheel. The Ridgid listing states a quick-acting design with an X-Cel knob, but does not say one-handed.
What metals does each listing name?
The KNIPEX listing names copper, brass, and high-grade steel. The Ridgid listing names trades like plumbing, HVAC and electrical work, but no tube materials.
What warranty does each listing state?
The Ridgid listing states a lifetime warranty on material defects and workmanship for the normal life of the product. The KNIPEX listing states only a Limited Warranty, with no term stated.
Do these cutters need power?
No. Both listings state a hand-powered source, so neither needs a battery, a cord or an outlet. The cutting force comes from the hand turning the tool.
Related: best angle grinder for cutting metal, best cut off wheels for metal, and the metal fab tools hub.
Scoring, line by line
Both cutters are scored on performance, build, value, safety listing and warranty, with the weights published on the How We Pick page.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Ridgid 31642 Tubing Cutter | 9.7 | 29 | 21 | 21 | n/a | 4 |
| KNIPEX TubiX Pipe Cutter | 9.6 | 28 | 21 | 20 | n/a | 0 |
A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number. Where safety does not apply (unpowered gear with no listed safety features), it is left out and the remaining 90 points make up the score.




