Portable Mig vs Portable Stick Welder: Which One Should You Buy?
Portable mig vs portable stick welder: a 160A 3-in-1 MIG machine and three stick welders described from the listings, with four machines compared.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
VEVOR 50FT Welder Extension Cord 40 Amp 250V 10 Gauge9.6/10View on Amazon - 2
Portable 2000 Watt Engine Driven Welder 130 Amp Stick Welder9.2/10View on Amazon - 3
VEVOR Welder Extension Cord 30 Amp 50 Feet9.4/10View on Amazon - 4
160A MIG WelderView on Amazon - 5
GNI Multiprocess Portable MINI WelderView on Amazon - 6
ARCCAPTAIN 130A Flux Core Welder MIG Welder 110V Gasless MIGView on Amazon - 7
FEIFANKE 135A Flux Core MIG Welder 3 in 1 Portable WeldingView on Amazon - 8
AWT MIG Welder 140AView on Amazon - 9
ARCCAPTAIN 160A MIG Welder 110V 220V Gasless Gas MIG StickView on Amazon
Portable mig vs portable stick welder comes down to process and portability: the one MIG-capable listing here is a 160A 3-in-1 machine for flux-cored MIG, Lift TIG and stick at 9.15 lb, while the stick side runs from two 3.3 lb handheld units to a 200A dual-voltage machine with a 2-year warranty. One honest note up front: only one listing welds MIG, so this guide describes each machine from its listing and tells you how to weigh the process question.
Other welders and gear to compare
160A MIG WelderCheck price on Amazon
GNI Multiprocess Portable MINI WelderCheck price on Amazon
ARCCAPTAIN 130A Flux Core Welder MIG Welder 110V Gasless MIGCheck price on Amazon
FEIFANKE 135A Flux Core MIG Welder 3 in 1 Portable WeldingCheck price on Amazon
AWT MIG Welder 140ACheck price on Amazon
ARCCAPTAIN 160A MIG Welder 110V 220V Gasless Gas MIG StickCheck price on Amazon
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Portable mig vs portable stick welder: the difference in one paragraph
From the listings, portable MIG means the PANERGYRIC 160A 3-in-1: gasless flux-cored MIG plus Lift TIG and stick, 110/220V dual voltage, with synergic control that matches voltage and wire speed to the wire diameter and current. Portable stick means three machines: the HGNVGZ and Protmex handhelds (110V, 20-120A, 3.3 lb each, rods included) and the Rotvik 200A (20-200A, 110/220V, stick plus Lift TIG with an argon arc gun). If you want wire feed, the PANERGYRIC is the only listing that offers it.
Side by side
| Product | Processes | Output | Voltage | Weight | Warranty |
|---|---|---|---|---|---|
| Rotvik 200A Dual Voltage | Stick / Lift TIG | 20-200A | 110/220V | 12.03 lb | 2 Year Manufacturer |
| PANERGYRIC 160A 3-in-1 | Flux MIG / Lift TIG / Stick | 160A max | 110/220V | 9.15 lb | Not stated |
| Protmex Handheld Stick | Stick | 20-120A | 110V | 3.3 lb | Not stated |
| HGNVGZ Handheld Stick | Stick | 20-120A | 110V | 3.3 lb | Not stated |
What portable MIG means here
The PANERGYRIC is the MIG side of this comparison: a 3-in-1 machine for gasless flux-cored MIG, Lift TIG and stick, with a maximum output of 160A. It runs 110/220V dual voltage with automatic input identification, carries a big LED digital display, and uses synergic control to match voltage and wire feed speed. The package includes the 14AK MIG torch, earth clamp, stick holder, flux-core wire, conductive nozzles, a 110V-to-220V adapter, brush and manual. At 9.15 lb it is the middleweight here: heavier than the handhelds, lighter than the Rotvik. No warranty term is stated.
What portable stick means here
Three listings weld stick. The HGNVGZ handheld runs 110V with 20-120A output, hot start, arc force and anti-stick, welding 1/8-inch steel with 3/32-inch rods and below, and accepts E6011, E6013, E6014 and E7018. The Protmex handheld is nearly its twin: 110V, 20-120A via a 5-position knob, 3.3 lb, hot start and anti-stick, with 20 rods and a full kit in a carry bag. The Rotvik is the heavyweight: 20-200A, 110/220V dual voltage, stick plus Lift TIG with an argon arc welding gun, four layers of safety protection, and a stated 2-year manufacturer warranty. The Rotvik is the only stick listing with a warranty term.
The gear: four portable welders, ranked
The Rotvik 200A tops the ranking: the highest output here (20-200A), dual voltage, stick plus Lift TIG, and the only stated warranty at 2 years. The PANERGYRIC 160A 3-in-1 follows as the only MIG-capable machine, with dual voltage and synergic control. The Protmex handheld is the kit pick: 20-120A, 3.3 lb, with mask, glasses, gloves, slag hammer, clamps, holder, 20 rods and a carry bag. The HGNVGZ handheld rounds out the set: 20-120A, 3.3 lb, with 20 rods, gloves, ground clamp, mask and case. Both handhelds plug into standard 110V outlets.
Weight and power
The weights split by form factor: 3.3 lb for each handheld (HGNVGZ and Protmex, per the bullets), 9.15 lb for the PANERGYRIC (spec table) and 12.03 lb for the Rotvik (spec table). Output runs 20-120A on the handhelds, 160A maximum on the PANERGYRIC and 20-200A on the Rotvik. Voltage: 110V only on the handhelds, 110/220V dual on the PANERGYRIC and Rotvik. Match the machine to the work: the handhelds for quick repairs, the dual-voltage machines for higher-output work.
What is in the box
The kits vary widely. The PANERGYRIC ships the machine with a 14AK MIG torch, earth clamp, stick holder, flux-core wire, two conductive nozzles, a 110V-to-220V adapter, brush and manual. The HGNVGZ ships the handheld welder with 20 3/32-inch rods, welding gloves, a ground clamp cable, a carrying case, a mask and instructions. The Protmex ships a mask, safety glasses, gloves, a slag hammer and brush, a ground clamp, an electrode holder, 20 rods and a manual in a durable carry bag. The Rotvik ships upgraded thick welding gloves, an argon arc welding gun, a 220V adapter, a welding helmet, an electrode holder, a ground clamp, a shoulder strap, a cleaning brush and 20 rods. The Protmex and Rotvik are the most complete out of the box.
Safety features
Three listings detail protection. The HGNVGZ states over-heating, over-current and over-load protection with 360-degree cooling vents for the IGBT inverter. The Protmex states an automated thermal management system with built-in overload protection, 360-degree cooling and an anti-stick function. The Rotvik states four layers of protection: overvoltage, overcurrent, overheating and anti-sticking strips. The PANERGYRIC states no safety features. For longer sessions, the stated thermal management on the three stick machines is the meaningful difference.
Current control
The HGNVGZ uses a 6-level current knob to match current to the job. The Protmex uses a 5-position rotary knob for 20 to 120 amps. The PANERGYRIC uses synergic control with a big LED digital display, matching voltage and wire speed to the wire diameter and current. The Rotvik uses a digital display panel with precise current regulation. Knobs suit gloved hands in the field; the digital displays suit the bench.
FAQ for welders
Which is better for a beginner, MIG or stick?
The listings describe the processes, not the learning curve. The PANERGYRIC is the only MIG-capable listing, with synergic control that matches voltage and wire speed. The HGNVGZ and Protmex run 3/32-inch rods; the Rotvik includes 20 rods with no size stated. Choose by the process you want to learn.
Can I run these on a normal outlet?
The HGNVGZ and Protmex are designed for standard 110V household outlets. The PANERGYRIC and Rotvik accept 110V and 220V with automatic identification, and both include a 110V-to-220V adapter.
Do the handheld welders really weigh 3.3 lb?
That is the figure in both handheld listings’ bullets. The spec tables list higher package weights (6.63 and 6.71 lb), which include the kits. The bare handheld is the 3.3 lb figure.
Which listing states a warranty?
Only the Rotvik: a 2-year manufacturer warranty. The HGNVGZ points to the Amazon order page for warranty details with no term stated; the PANERGYRIC and Protmex state no warranty term.
Related: the best portable stick welder, the best flux core welder and portable vs stationary welder.




