Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Spot Welder Parts: Electrodes and Replacement Guide

Spot welder parts are the wear and replacement pieces that carry current to the weld, and matching thread, tip size and material to the welder keeps welds consistent.

Spot Welder Parts: Electrodes and Replacement Guide
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1RALBIL Dent Puller Welder 3.5KW Spot Welder Dent PullerRALBIL Dent Puller Welder 3.5KW Spot Welder Dent Puller9.7/10View on Amazon
  2. 2Battery Spot WelderBattery Spot Welder9.5/10View on Amazon
  3. 3Spot Welder Dent Puller Machine Body Repair Dent RemovalSpot Welder Dent Puller Machine Body Repair Dent Removal9.5/10View on Amazon

Spot welder parts are the replaceable pieces that carry welding current from the arms to the sheet metal and form the weld spot. Electrodes and tips wear down, arms are swapped when reach is the problem, and caps and pins reach the end of their service life, so knowing each part, its thread and its tip size makes replacement a matter of matching the part to the welder instead of guessing. This guide explains electrodes, tips, arms, caps and pins, how to match them to a welder, and when to swap a worn part for a fresh part.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

What spot welder parts do

A spot welder squeezes sheet metal between electrodes and passes current through the joint for a short pulse, and the parts in that path decide where the heat goes. The electrode tip is the contact face, the arm holds the tip and sets the reach, and caps are the small wear pieces for the gun, and pins fit holders and pens for battery work. When a tip face mushrooms, the current spreads over a wider area and spots turn weak and uneven, so a fresh tip with a crisp contact face restores the same small, clean weld spot. Copper carries the current, and the listings here name solid copper, C18200 chrome copper and alumina copper.

Spot Welder Parts Side by Side

Electrode tips Arms and tongs Caps and pins
Part Replaceable tip at the end of the arm Arm that holds the tip and reaches the joint Cap or pin that fits a holder or pen
Thread M8-1.25 or 3/8-24 M8-1.25 No thread; fits 3 mm holders
Tip face 1/8 inch, 5/32 inch or 1/4 inch 1/8 inch contact tips Conical tips on pins; 13 mm cap diameter
Material Solid copper or C18200 chrome copper C18200 chrome copper Alumina copper pins; cap material not stated
Pack 1 pair or 4 pcs 1 pair of arms with 1 pair of tips 40 pack of caps; 4 pcs of pins
Use Spot welding; draw pins and trim rivets Auto panels, cabinets, boxes and sheet metal Battery packs, nickel strip and Chief spot welders

Read the table by fit, then by use. A tip with the wrong thread will not thread onto the arm at all, and a cap with the wrong diameter will not seat on the gun, so thread and size come before material and pack size when choosing a replacement.

When electrode tips are the part to replace

Replace the tip when the face mushrooms, when spots turn weak and uneven, or when the face no longer makes clean contact with the sheet. The listings name tip faces of 1/8 inch, 5/32 inch and 1/4 inch, and the face size sets the size of the weld spot, with a smaller face giving a smaller spot on light-gauge material. Motor Guard lists a copper stud welding tip for draw pins and a trim rivet electrode for its Magna-Spot stud welders, and Thrasher Products lists Miller-style tips in C18200 chromium copper alloy for Miller-TT-6, TT-9 and G7 welding tongs.

  • Check the thread before ordering. Tips here use M8-1.25 metric thread or 3/8-24 mounting thread, and an imperial thread will not accept a metric tip.
  • Match the face to the work. A 1/8 inch face suits small spots on light-gauge material, while a 1/4 inch contact area suits a larger spot.
  • Keep the face clean. Cleaning or trimming the electrode head after daily use helps maintain a stable welding effect.

When arms and caps are the part to replace

Arms are the part to replace when reach is the problem, and caps are the part to replace when the contact face on the gun wears out. Sosation lists 18 inch spot welder arms in C18200 chrome copper, with M8-1.25 threaded connections and 1/8 inch contact tips, for auto panels, cabinets, boxes and overlapping sheet metal, made to replace or extend existing arms where access is limited. Spot weld caps in 13 mm Type A come in a 40 pack with a storage case, as replacements for Chief and GYS part numbers, for Chief spot welders and water-cooled and non-water-cooled units.

For the machine itself, see our best spot welder for hobbyists guide, and for auto body work see our best spot welder for auto body guide.

How to match thread and tip size

Matching starts with the thread on the arm, then the tip face, then the holder. The listings here use M8-1.25 metric thread and 3/8-24 mounting thread, and they do not interchange, so confirm the thread on the arm before ordering. Pidnsrozo lists 1/8 inch spot welding tips with M8-1.25 metric thread in a 4 pcs pack, and the maker notes that arms vary between welder brands, so a thread check before ordering keeps every tip a drop-in fit. For Sosation arms (on Amazon), the maker lists these steps: power off, remove the old arms, mount the replacements to the upper and lower holders, insert M8-1.25 tips, align and set pressure, then place the workpiece, set parameters, clamp and weld.

Pins follow the same rule on a smaller scale. SING F LTD lists 3×50 mm double-ended electrodes for 3 mm holders, with conical tips on each end, and the double-ended shape lets the pin be indexed and rotated when an end wears. A pin that slides into a 3 mm collet and tightens with a set screw is a fit for bench or handheld pens, for battery pack building, nickel strip and thin sheet joints.

Which material and tip face to choose

Copper is the common material across these parts, and the alloy matters because the tip carries current and heat on every weld. C18200 chrome copper appears in the Thrasher tips and the Sosation arms, solid copper appears in the Pidnsrozo tips (on Amazon), and alumina copper appears in the SING F LTD pins (on Amazon), where the maker notes stable conductivity and wear resistance under repeated pulses. A larger tip face spreads current over a wider area, so a mushroomed face gives weak and uneven spots.

Can a worn tip be cleaned instead of replaced?

Cleaning or trimming the electrode head after daily use can maintain a stable welding effect, and the Sosation listing names that care routine for its arms and tips. A tip face that has mushroomed past a clean shape, or a tip that gives weak and uneven spots after cleaning, has reached the end of its service life and needs a fresh tip. Keep a backup tip on hand, and check the thread and face size on the replacement before threading it in.

Heat, current and fumes. Spot welding puts current and heat through the joint, so keep the work clamped and the hands clear of the electrodes, weld with ventilation or outdoors with the head out of the plume, and clear anything flammable from the area. Power off before swapping arms or tips. See our Safety Disclaimer.

FAQ for welders

What are spot welder parts?

Spot welder parts are the replaceable electrodes, tips, arms, caps and pins that carry current to the joint and form the weld spot. Tips and caps are wear parts, arms set reach and fit, and pins fit holders and pens for battery work.

How do I know which tip thread my spot welder uses?

Check the thread on the electrode arm before ordering, and match the tip to that thread. The listings here use M8-1.25 metric thread and 3/8-24 mounting thread, and an imperial thread will not accept a metric tip.

When should a spot welder tip be replaced?

Replace a tip when the face mushrooms, when spots turn weak and uneven, or when cleaning and trimming no longer restore a crisp contact face. A fresh tip of the stated face size restores the same small, clean weld spot.

What is the difference between spot welder tips and caps?

Tips thread onto the arms and carry current through a contact face, while caps are the replaceable contact face for the gun on water-cooled and non-water-cooled units. The caps here are 13 mm Type A in a 40 pack, and the tips here use M8-1.25 or 3/8-24 thread with faces of 1/8 inch, 5/32 inch or 1/4 inch.

Can spot welder parts fit a battery spot welder?

Yes, when the holder and pin size match. SING F LTD lists 3×50 mm double-ended pins for 3 mm holders and portable battery spot welders, for 18650 pack building, nickel strip and thin sheet joints.

Related: spot welder tips, uses for a spot welder, spot welder vs MIG welder, and the welders hub. Also see our MIG welder replacement parts.

More buying guides

Welders ·

Best Spot Welder for Auto Body (2026)

Three stud welder dent puller kits for auto body repair, compared on power, welding modes, studs, weight and the voltage each listing states.