Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Size S Drill Bit: What It Is and When to Use It

A size S drill bit is a letter gauge bit near the large end of the letter series, sized for holes where a fractional bit lands just off.

Size S Drill Bit: What It Is and When to Use It
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1NEIKO 10185A Step Drill BitNEIKO 10185A Step Drill BitView on Amazon
  2. 2NEIKO 10194A Step Drill BitNEIKO 10194A Step Drill BitView on Amazon
  3. 3NEIKO 10182A Titanium Step Drill BitNEIKO 10182A Titanium Step Drill BitView on Amazon
  4. 4NEIKO 10184A Step Drill BitNEIKO 10184A Step Drill BitView on Amazon
  5. 5NEIKO 10198A Step Drill Bit SetNEIKO 10198A Step Drill Bit SetView on Amazon
  6. 6DEWALT Drill Bit SetDEWALT Drill Bit SetView on Amazon

A size s drill bit is a letter gauge bit, part of the letter sizes that run from A to Z. When the fractional bit in the set leaves a hole a touch too tight or a touch too loose, a letter bit fills that gap. This guide explains what the S size is, where it sits in the letter series, and how to put it to work in the shop.

Other welders and gear to compare

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

What a size s drill bit is

Drill bits come in sizing systems, and the letter gauge is one of them. Fractional bits are named by fractions of an inch, number bits by a number, and metric bits by millimeters. Letter bits are named by letters, and the series runs from A, the smallest, to Z, the largest. S sits near the large end of that run, which makes it a mid to large shop bit rather than a fine one.

The letter is stamped on the shank, so the size is easy to read once the bit is out of the case. A size S bit looks like any other twist bit at a glance, and nothing about its shape marks it as a letter size. The letter on the shank is the only thing that sets it apart from a fractional bit of nearly the same diameter.

How letter sizes compare

Letter bits exist because fractional steps leave gaps. A shop that only owns fractional bits can find a hole that needs to sit between two of them, and a letter bit lands in that gap. The table below sets the sizing systems side by side.

Letter gauge Fractional Number gauge Metric
How sizes are named Letters A to Z Fractions of an inch Numbers Millimeters
Step between sizes One letter at a time One fraction at a time One number at a time Small steps in millimeters
Where size S belongs Letter series Not a fractional size Not a number size Not a metric size
What to check Letter stamped on the shank Fraction stamped on the shank Number stamped on the shank Size stamped on the shank
Shop use Tapping and clearance holes General drilling Small precision holes Hardware sized in millimeters

Read the table as a map, not a shopping list. The letter series covers one stretch of the fractional range in finer steps, and S is one of its larger letters. When a chart is on the bench, the letter column is the one to check first for a size S hole.

The drilling and tapping chart and tapping drill chart show how letter, number and fractional sizes line up for tapping and clearance work.

When to reach for size S

Reach for size S when the job calls for a hole that a fractional bit cannot quite match. Common cases are a clearance hole for a bolt that binds on the fractional size below it, and a tap drill where the fractional size above it cuts the thread too shallow. The letter bit splits the difference and the fastener seats the way it should.

  • Clearance holes. A bolt that drags through a fractional hole passes clean through the next letter size up, and S is the letter to try when the fractional size below it binds.
  • Tap drills. A tap needs a hole that leaves enough thread without forcing the tap, and a letter bit can land closer to that hole than either neighboring fractional size.
  • Reaming and fitting. A hole that needs a light ream or a snug pin fit benefits from starting a touch under size, and a letter bit gives that starting point where fractional bits jump past it.
  • Matching existing holes. A worn or factory hole that measures near S can be cleaned up with the S bit instead of opening it up to the next fractional size.

When a different size fits better

Size S is not the answer for every hole. A fractional bit is the right call when the drawing or the hardware calls for a fractional size, and forcing a letter bit into that job only adds confusion. A smaller letter or number bit fits better when the hole needs to stay tight for a thread or a press fit, and a larger fractional bit fits better when the hole is a rough clearance pass that will be reamed later.

If the bit is missing from the set, the nearest letter above or below S can stand in for light work, but the hole will run a touch larger or smaller than S, so check the fit before committing to the full run. For a tapped hole, that small change can turn a clean thread into a loose one, so match the chart rather than guessing.

How to use a size S drill bit

Using a letter bit is the same as using any twist bit, with the same care around layout and clamping. Work through the steps in order and let the bit cut at its own pace.

  1. Mark the hole. Lay out the center with a center punch so the bit starts where it should and does not wander across the face.
  2. Clamp the work. Hold the piece in a vise or clamp it to the bench so it cannot spin or lift when the bit breaks through.
  3. Start slow. Bring the bit to the mark at a slow speed and let the point bite before adding pressure.
  4. Peck and clear chips. Lift the bit to clear chips from the flutes, and add cutting fluid on steel to keep the edge cool.
  5. Check the fit. Try the bolt or tap in the hole before drilling the rest of the run, and adjust the size if the fit is off.

Eye protection and clamping. Wear eye protection, clamp the work, and keep gloves away from rotating parts. Keep guards in place on the drill press, and clear chips with a brush rather than a bare hand.

For steel, a cutting fluid helps the bit last longer and leaves a cleaner hole. The best cutting fluid for steel guide covers picks for drilling, tapping and sawing, and the best drill bit for stainless steel metal guide covers bits built for hard metal.

A letter set keeps R, S and T together so the next size up or down is on hand. The best drill bit set for impact driver guide covers hex shank sets for shop and site work.

For more options, see our guides guides.

FAQ for welders

What does the S in a size S drill bit mean?

The S is a letter in the letter gauge series, which names drill bits with letters instead of fractions or numbers. The series runs from A to Z, and S sits near the large end. A size S bit is a twist bit like any other, and the letter on the shank is what names it.

Is a size S drill bit the same as a fractional bit?

No. A fractional bit is named by a fraction of an inch, while a size S bit is named by its letter in the letter gauge series. The two systems overlap in size, so S lands near a fractional size without matching it exactly. Use the letter size when the fractional bit leaves the hole too tight or too loose.

What is a size S drill bit used for?

Size S suits clearance holes for bolts and tap drills for threads, where a fractional bit lands just off the hole the job needs. It also fits reaming and fitting work where the hole starts a touch under size. Any job that needs a hole between two fractional sizes is a candidate for a letter bit.

How do I know if I need a letter size bit?

Try the fractional bit first. If the bolt binds in the hole or the tap cuts too shallow, the hole needs a size between two fractional steps, and a letter bit fills that gap. A drill chart shows where the letters land, so check the chart before ordering a bit for a tapped hole.

Can I use a size S bit in a hand drill?

Yes, with the same care as any twist bit. Mark the hole with a center punch, clamp the work so it cannot spin, and start at a slow speed. Add cutting fluid on steel, clear chips from the flutes, and check the fit before drilling the rest of the run.

Related: drilling and tapping chart, tapping drill chart, best drill bit for stainless steel metal, and best drill bit set for impact driver.

More buying guides